EN ISO 17824:2014

Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)

ISO 17824:2009 provides the requirements and guidelines for sand control screens for use in the petroleum and natural gas industries. Included are the requirements for design, design validation, functional evaluation, manufacturing, storage and transport. The requirements of ISO 17824:2009 are applicable to wire-wrap screens, pre-pack screens and metal-mesh screens as defined herein.
The following items are outside the scope of ISO 17824:2009: expandable sand screens, slotted liners or tubing and accessory items such as centralizers or bull plugs; shunt screen technology, inflow control devices, downhole sensors and selective isolation devices, even though they can be an integral part of the sand control screen; screen filtration performance criteria, including test methods or analysis for sand retention efficiency; and end connections of the basepipe.

Erdöl- und Erdgasindustrie - Bohrlochausrüstungen - Sandfilter (ISO 17824:2009)

Industries du pétrole et du gaz naturel - Equipement de fond de puits - Tamis de contrôle de sable (ISO 17824:2009)

Industrija za predelavo nafte in zemeljskega plina - Oprema za vrtine - Peščeni filter (ISO 17824:2009)

V tem mednarodnem standardu so podane zahteve in navodila za peščene filtre za uporabo v industriji za predelavo nafte in zemeljskega plina. Vključuje zahteve za oblikovanje, potrditev oblike, oceno delovanja, izdelavo, shranjevanje in prevoz. Zahteve tega mednarodnega standarda se uporabljajo za z žico obdane filtre, predpakirane filtre in kovinske mrežaste filtre, določene v tem standardu. Naslednji elementi ne spadajo na področje uporabe tega mednarodnega standarda:
– razširljivi peščeni filtri, režasti vsebniki ali cevi in dodatni elementi, kot so centralizatorji ali zamaški;
– tehnologija filtrov s kanali, naprave za nadzor dotoka, senzorji v vrtinah in selektivne ločilne naprave, tudi
kjer so sestavni del peščenega filtra;
– merila za učinkovitost filtracije filtra, vključno s preskusnimi metodami ali analizo za učinkovitost zadrževanja peska;
– zaključne povezave osnovne cevi.

General Information

• Status: Published
• Publication Date: 05-Aug-2014
• Withdrawal Date: 27-Feb-2015
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 06-Aug-2014
• Due Date: 20-May-2015
• Completion Date: 06-Aug-2014
• Ref Project: SIST EN ISO 17824:2014 - Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Erdöl- und Erdgasindustrie - Bohrlochausrüstungen - Sandfilter (ISO 17824:2009)Industries du pétrole et du gaz naturel - Equipement de fond de puits - Tamis de contrôle de sable (ISO 17824:2009)Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)75.180.10Oprema za raziskovanje in odkopavanjeExploratory and extraction equipmentICS:Ta slovenski standard je istoveten z:EN ISO 17824:2014SIST EN ISO 17824:2014en01-oktober-2014SIST EN ISO 17824:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 17824
August 2014 ICS 75.180.10 English Version
Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)
Industries du pétrole et du gaz naturel - Equipement de fond de puits - Tamis de contrôle de sable (ISO 17824:2009)
Erdöl- und Erdgasindustrie - Bohrlochausrüstungen - Sandfilter (ISO 17824:2009) This European Standard was approved by CEN on 31 July 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17824:2014 ESIST EN ISO 17824:2014

Reference numberISO 17824:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO17824First edition2009-08-15Petroleum and natural gas industries — Downhole equipment — Sand screens Industries du pétrole et du gaz naturel — Equipement de fond de puits — Tamis de contrôle de sable
ISO 17824:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 17824:2009(E) © ISO 2009 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Abbreviated terms.6 5 Functional specification.6 5.1 General.6 5.2 Product type.7 5.3 Sand screen parameters.7 5.4 Well parameters.7 5.5 Operational parameters.7 5.6 Environmental compatibility.8 5.7 Compatibility with related well equipment.8 5.8 Design validation grades.8 5.9 Quality grades.8 5.10 Special quality requirements.8 6 Technical specification.9 6.1 General.9 6.2 Technical characteristics.9 6.3 Design criteria.9 6.4 Design verification.9 6.5 Design validation.10 6.6 Design changes.10 6.7 Design validation by scaling.11 7 Supplier/manufacturer requirements.13 7.1 General.13 7.2 Documentation and data control.13 7.3 Product identification.14 7.4 Quality control.14 8 Storage and transport.23 8.1 Storage.23 8.2 Product protection.23 8.3 Transport.23 Annex A (normative)
Collapse pressure test.24 Annex B (normative)
Burst pressure test.27 Annex C (informative)
Sized-bead test method.30 Annex D (informative)
Sand control screen illustrations.32 Annex E (informative)
Wire-wrap screen illustrations.34 Annex F (informative)
Pre-pack screen illustrations.35 Annex G (informative)
Metal-mesh screen illustrations.36 Annex H (informative)
Increased wire-wrap slot size inspection.37 Bibliography.38 SIST EN ISO 17824:2014

ISO 17824:2009(E) iv © ISO 2009 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17824 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production equipment. SIST EN ISO 17824:2014

ISO 17824:2009(E) © ISO 2009 – All rights reserved vIntroduction This International Standard has been developed by user/purchasers and supplier/manufacturers of sand control screens intended for use in petroleum and natural gas wells. This International Standard provides requirements and information to both parties regarding the manufacture, mechanical properties and testing of sand control screens. Further, this International Standard addresses supplier/manufacturer requirements that set the minimum parameters with which it is necessary that supplier/manufacturers comply to claim conformity with this International Standard. This International Standard is structured with grades of increased requirements for both design validation and quality control. Three design validation grades (V
...