EN ISO 15119:2004

Packaging - Sacks - Determination of the friction of filled sacks (ISO 15119:2000)

This International Standard specifies three methods for the determination of the friction of filled sacks.

Verpackung - Säcke - Bestimmung der Reibung gefüllter Säcke (ISO 15119:2000)

In dieser Internationalen Norm werden drei Verfahren zur Bestimmung der Reibung gefüllter Säcke festgelegt.

Emballages - Sacs - Détermination du frottement des sacs pleins (ISO 15119:2000)

La présente Norme internationale spécifie trois méthodes de détermination du frottement des sacs pleins.

Embalaža – Vreče – Določevanje trenja pri polnih vrečah (ISO 15119:2000)

General Information

• Status: Published
• Publication Date: 31-Aug-2004
• ICS: 55.080 - Sacks. Bags
• Technical Committee: CEN/TC 261 - Packaging
• Drafting Committee: CEN/TC 261/SC 5 - Primary packaging and transport packaging
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 23-Oct-2009
• Completion Date: 23-Oct-2009
• Directive: 80/232/EEC - Ranges of nominal quantities and nominal capacities permitted for certain pre-packaged products
• Directive: 87/356/EEC - Ranges of nominal quantities and nominal capacities permitted for certain pre-packged products (Dir. 80/232/EEC amendment)
• Ref Project: SIST EN ISO 15119:2005 - Packaging - Sacks - Determination of the friction of filled sacks (ISO 15119:2000)

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2005
(PEDODåD±9UHþH±'RORþHYDQMHWUHQMDSULSROQLKYUHþDK,62
Packaging - Sacks - Determination of the friction of filled sacks (ISO 15119:2000)
Verpackung - Säcke - Bestimmung der Reibung gefüllter Säcke (ISO 15119:2000)
Emballages - Sacs - Détermination du frottement des sacs pleins (ISO 15119:2000)
Ta slovenski standard je istoveten z: EN ISO 15119:2004
ICS:
55.080 9UHþH9UHþNH Sacks. Bags
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15119
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2004
ICS 55.080
English version
Packaging - Sacks - Determination of the friction of filled sacks
(ISO 15119:2000)
Emballages - Sacs - Détermination du frottement des sacs Verpackung - Säcke - Bestimmung der Reibung gefüllter
pleins (ISO 15119:2000) Säcke (ISO 15119:2000)
This European Standard was approved by CEN on 15 July 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15119:2004: E
worldwide for CEN national Members.

Foreword
The text of ISO 15119:2000 has been prepared by Technical Committee ISO/TC 122
"Packaging” of the International Organization for Standardization (ISO) and has been taken over
as EN ISO 15119:2004 by Technical Committee CEN/TC 261 "Packaging", the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2005, and conflicting national
standards shall be withdrawn at the latest by March 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 15119:2000 has been approved by CEN as EN ISO 15119:2004 without any
modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).

Annex ZA
(normative)
Normative references to international publications
with their relevant European publications

This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).

NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.

Publication Year Title EN Year

ISO 7023 1983 Packaging - Sacks - Method of EN 27023 1992
sampling empty sacks for testing

INTERNATIONAL ISO
STANDARD 15119
First edition
2000-07-01
Packaging — Sacks — Determination of the
friction of filled sacks
Emballages — Sacs — Détermination du frottement des sacs pleins
Reference number
ISO 15119:2000(E)
©
ISO 2000
ISO 15119:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

ISO 15119:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15119 was prepared by Technical Committee ISO/TC 122, Packaging, Subcommittee
SC 2, Sacks.
ISO 15119:2000(E)
Introduction
This International Standard specifies three methods for the determination of the friction of filled sacks.
The friction of filled sacks is of importance for sacks which are usually stacked for transport and/or storage. It is
important to determine the friction filled sacks will undergo so as to detemine, for example, if additional strapping is
necessary when transporting palletized loads or, if additional means are necessary when loading a pallet with
sacks.
The friction of filled sacks is influenced not only by the material of the sack, but also by the printing on the sack, the
characteristics of the filling commodity of the sack and the filling degree of the sack. Therefore this International
Standard specifies test methods for sacks filled as is intended for final use.
The methods in this International Standard are intended to be an aid to designers and users of sacks to make the
right choice for the type of sack for a given
...