EN ISO 11403-3:2021

Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2021)

This document specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments:
—    prolonged exposure to heat;
—    liquid chemicals;
—    environmental stress cracking under a constant tensile stress;
—    artificial weathering.
The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 3: Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:2021)

Dieses Dokument legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunkt Kennwerten fest, die das Verhalten von Kunststoffen gegenüber den folgenden Umgebungseinflüssen darstellen:
- langanhaltende Wärmeeinwirkung;
- flüssige Chemikalien;
- umgebungsbedingte Spannungsrissbildung unter konstanter Zugspannung;
- künstliche Bewitterung.
Die Prüfungen sind in der Reihenfolge zunehmender Schärfe der Umgebungseinflüsse aufgeführt. Durch anfängliche Prüfung bei den am wenigsten scharfen Umgebungseinflüssen ist es möglich, fundierte Entscheidungen zu treffen, ob Prüfungen unter schärferen Bedingungen sinnvoll sind.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 3: Effets induits par l'environnement sur les propriétés (ISO 11403-3:2021)

Le présent document spécifie les modes opératoires d’essai en vue de l’acquisition et de la présentation de données multiples qui démontrent le comportement des plastiques dans les environnements suivants :
—    exposition prolongée à la chaleur ;
—    produits chimiques liquides ;
—    fissuration dans un environnement donné sous contrainte de traction constante ;
—    vieillissement artificiel.
Les essais sont indiqués par ordre de sévérité croissante de l’effet de l’environnement. Commencer par les environnements les moins sévères permet de juger en toute connaissance de cause s’il vaut la peine d’effectuer des essais dans des conditions plus sévères.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 3. del: Vplivi okolja na lastnosti (ISO 11403-3:2021)

General Information

• Status: Published
• Publication Date: 29-Jun-2021
• Withdrawal Date: 30-Dec-2021
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 30-Jun-2021
• Completion Date: 30-Jun-2021
• Ref Project: SIST EN ISO 11403-3:2021 - Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2021)

Relations

• Replaces: EN ISO 11403-3:2014 - Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)
• Effective Date: 07-Jul-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2021
Nadomešča:
SIST EN ISO 11403-3:2014
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 3. del: Vplivi okolja na lastnosti (ISO 11403-3:2021)
Plastics - Acquisition and presentation of comparable multipoint data - Part 3:
Environmental influences on properties (ISO 11403-3:2021)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
3: Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:2021)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 3:
Effets induits par l'environnement sur les propriétés (ISO 11403-3:2021)
Ta slovenski standard je istoveten z: EN ISO 11403-3:2021
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11403-3
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2021
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 11403-3:2014
English Version
Plastics - Acquisition and presentation of comparable
multipoint data - Part 3: Environmental influences on
properties (ISO 11403-3:2021)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von
multiples comparables - Partie 3: Effets induits par vergleichbaren Vielpunkt-Kennwerten - Teil 3:
l'environnement sur les propriétés (ISO 11403- Umgebungseinflüsse auf Eigenschaften (ISO 11403-
3:2021) 3:2021)
This European Standard was approved by CEN on 6 June 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-3:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11403-3:2021) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-3:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11403-3:2021 has been approved by CEN as EN ISO 11403-3:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 11403-3
Third edition
2021-06
Plastics — Acquisition and
presentation of comparable
multipoint data —
Part 3:
Environmental influences on
properties
Plastiques — Acquisition et présentation de données multiples
comparables —
Partie 3: Effets induits par l'environnement sur les propriétés
Reference number
ISO 11403-3:2021(E)
©
ISO 2021
ISO 11403-3:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

ISO 11403-3:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Specimen preparation . 2
5 Conditioning . 3
6 Test requirements . 3
6.1 General . 3
6.2 Indicative properties and indicative data . 4
6.3 Test specimens . 4
6.4 Test speed . 4
6.5 Prolonged exposure to heat: ISO 2578 . 4
6.6 Liquid chemicals . 6
[10]
6.7 Environmental stress cracking under constant tensile stress: ISO 22088 . 6
6.8 Artificial weathering: ISO 4892-2 . 8
6.9 Set of exposure conditions 1: Open air . 8
6.10 Set of exposure conditions 2: Behind glass, low temperature . 8
6.11 Set of exposure conditions 3: Behind glass, high temperature . 9
7 Presentation of data . 9
8 Precision .11
Annex A (informative) Information relating to certain test requirements .12
Annex B (normative) Chemicals for chemical resistance and environmental stress cracking
resistance tests .14
Bibliography .15
ISO 11403-3:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical behaviour, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 11403-3:2014), of which it constitutes a
minor revision.
The changes compared to the previous edition are as follows:
— unified the indication methods of the unit;
— unified the quotation of the specimen shape in ISO 20753;
— performed the editorial corrections.
A list of all parts in the ISO 11403 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

ISO 11403-3:2021(E)
Introduction
This document has been prepared because users of plastics find sometimes that available data cannot
be used readily to compare the properties of similar materials, especially when the data have been
supplied by different sources. Even when the same standard tests have been used, they often allow
the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this document is to identify specific methods and conditions of test to be
used for the acquisition and presentation of data in order that valid comparisons between materials
can be made. These
...