EN ISO 12215-9:2018

Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)

ISO 12215-9:2011 defines the loads and specifies the scantlings of sailing craft appendages on monohull sailing craft with a length of hull of up to 24 m, measured according to ISO 8666. It gives design stresses, the structural components to be assessed, load cases and design loads for keel, centreboard and their attachments, computational methods and modelling guidance, and the means for compliance with its provisions.

Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 9: Anhänge von Segelbooten (ISO 12215-9:2012)

Petits navires - Construction de coques et échantillonnage - Partie 9: Appendices des bateaux à voiles (ISO 12215-9:2012)

L'ISO 12215-9:2011 définit les chargements et spécifie l'échantillonnage des appendices des bateaux à voiles d'une longueur de coque, LH, mesurée conformément à l'ISO 8666, inférieure ou égale à 24 m. Elle fournit: les contraintes de conception, les éléments structurels à évaluer, les cas de chargement et les charges de conception pour la quille, la dérive et leurs éléments de liaison, les méthodes de calcul et des instructions de modélisation et les moyens de se conformer à ses dispositions.

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 9. del: Dodatni pribor jadrnic (ISO 12215-9:2012)

Ta del standarda ISO 12215 določa obremenitve in dimenzioniranje dodatnega pribora jadrnic na jadrnicah z enim trupom, pri čemer dolžina trupa (LH), merjena v skladu s standardom ISO 8666, ne presega 24 m. Podaja:
– konstrukcijske napetosti;
– sestavne dele konstrukcije, ki jih je treba oceniti;
– primere obremenitve in konstrukcijske obremenitve za gredelj, premični gredelj ter njune priključke;
– računalniške metode in navodila za modeliranje;
– načine skladnosti z določbami standarda.

General Information

• Status: Published
• Publication Date: 02-Oct-2018
• ICS: 47.080 - Small craft
• Technical Committee: CEN/TC 464 - Small Craft
• Drafting Committee: CEN/TC 464 - Small Craft
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 03-Oct-2018
• Due Date: 03-Nov-2019
• Completion Date: 03-Oct-2018
• Directive: 2003/44/EC - Approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
• Directive: 2013/53/EU - Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC
• Mandate: M/542 - [C(2015)8736] Standardisation Request to the European Committee for Standardisation and the European Committee for Electro-technical Standardisation as regards recreational craft and personal watercraft in support of Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC.
• Ref Project: SIST EN ISO 12215-9:2018 - Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)

Relations

• Replaces: EN ISO 12215-9:2012 - Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)
• Effective Date: 07-Jun-2017
• Revised: prEN ISO 12215-9 - Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO/DIS 12215-9:2024)
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 12215-9:2012
Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 9. del: Dodatni pribor
jadrnic (ISO 12215-9:2012)
Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO
12215-9:2012)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 9: Anhänge von
Segelbooten (ISO 12215-9:2012)
Petits navires - Construction de coques et échantillonnage - Partie 9: Appendices des
bateaux à voiles (ISO 12215-9:2012)
Ta slovenski standard je istoveten z: EN ISO 12215-9:2018
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 12215-9
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 12215-9:2012
English Version
Small craft - Hull construction and scantlings - Part 9:
Sailing craft appendages (ISO 12215-9:2012)
Petits navires - Construction de coques et Kleine Wasserfahrzeuge - Rumpfbauweise und
échantillonnage - Partie 9: Appendices des bateaux à Dimensionierung - Teil 9: Anhänge von Segelbooten
voiles (ISO 12215-9:2012) (ISO 12215-9:2012)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-9:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
The text of ISO 12215-9:2012 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 12215-9:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12215-9:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 12215-9:2012 has been approved by CEN as EN ISO 12215-9:2018 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Clause(s)/sub- Remarks/Notes
Requirements of clause(s) of
Directive this EN
2013/53/EU
Annex I, Part A, 2.5 – 7.7.1, D.3.4, F.2.4.2 These clauses specify warnings and information to be
Owner’s manual included in the owner’s manual, if relevant.

Annex I, Part A, 3.1 - All clauses This part of ISO 12215 provides requirements for the
Structure strength of monohull sailing boat appendages with

conventional keel configurations. It deals with the design
stresses and structural efficiency of the keel and its
connections.
The load cases correspond to those for most
conventional keel configurations; however they may not
be appropriate in all cases and designers or builders still
need to ensure the suitability of their designs.
Scantlings derived from this standard are primarily
intended to apply to recreational sailing craft.
Dimensioning is regarded as reflecting current practice
provided the craft is correctly handled and operated at
speeds appropriate to the prevailing sea state.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 12215-9
First edition
2012-06-15
Small craft — Hull construction and
scantlings —
Part 9:
Sailing craft appendages
Petits navires — Construction de la coque et échantillonnage —
Partie 9: Appendices des bateaux à voiles

Reference number
ISO 12215-9:2012(E)
©
ISO 2012
ISO 12215-9:2012(E)
©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 12215-9:2012(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  Symbols . 3
5  Design stresses . 4
6  Structural components to be assessed . 6
7  Load cases . 6
7.1  General . 6
7.2  Load case 1 — Fixed keel at 90° knockdown . 7
7.3  Load case 2 — Canted keel steady load at 30° heel with dynamic overload factor . 8
7.4  Load case 3 — Keelboat vertical pounding . 9
7.5  Load case 4 — Keelboat longitudinal impact . 10
7.6  Load case 5 — Centreboard on capsize recoverable dinghies . 11
7.7  Load case 6 — Centreboard or dagger board upwind . 11
7.8  Other load cases . 12
8  Computational methods . 15
8.1  General . 15
8.2  General guidance for assessment by 3D numerical procedures . 15
8.3  Assessment by strength of materials/non-computational-based methods . 16
9  Compliance . 16
Annex A (normative) Application declaration . 18
Annex B (informative) Information on metal for appendages and fasteners and
“established practice” for fastening and welding . 19
Annex C (informative)  “Established practice” structural arrangement for ballast keels . 30
Annex D (informative) “Established practice” calculation of keel fin strength (fixed or canting)
and fixed ballast keel connected by bolts . 44
Annex E (informative) Geometrical properties of some typical appendage foil shapes . 61
Annex F (informative) Simplified fatigue strength assessment . 64
Bibliography . 76

ISO 12215-9:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12215-9 was prepared by Technical Committee ISO/TC 188, Small craft.
ISO 12215 consists of the following parts, under the general title Small craft — Hull construction and
scantlings:
 Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate
 Part 2: Materials: Core materials for sandwich
...