EN ISO 15854:2005
(Main)Dentistry - Casting and baseplate waxes (ISO 15854:2005)
Dentistry - Casting and baseplate waxes (ISO 15854:2005)
ISO 15854:2005 is applicable to dental casting wax and to dental baseplate wax. It specifies the classification of, and requirements for, dental casting wax and baseplate wax together with the test methods to be employed to determine compliance with these requirements.
Zahnheilkunde - Guss- und Basisplattenwachse (ISO 15854:2005)
Diese Internationale Norm gilt für dentale Gusswachse und für dentale Basisplattenwachse. Festgelegt werden die Einteilung von und die Anforderungen an dentale Gusswachse und Basisplattenwachse sowie die anzuwendenden Prüfverfahren, damit die Übereinstimmung mit diesen Anforderungen festgestellt werden kann.
Art dentaire - Cires pour coulée et pour plaque de base (ISO 15854:2005)
L'ISO 15854:2005 s'applique aux cires dentaires pour coulée et aux cires dentaires pour plaque de base. Elle spécifie la classification et les exigences relatives aux cires dentaires pour coulée et aux cires pour plaque de base ainsi que les méthodes d'essai à appliquer pour déterminer la conformité à ces exigences.
Zobozdravstvo - Voski za odlitke in podstavke (ISO 15854:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2005
1DGRPHãþD
SIST EN ISO 12163:2001
SIST EN ISO 1567:2001
Zobozdravstvo - Voski za odlitke in podstavke (ISO 15854:2005)
Dentistry - Casting and baseplate waxes (ISO 15854:2005)
Zahnheilkunde - Guss- und Basisplattenwachse (ISO 15854:2005)
Art dentaire - Cires pour coulée et pour plaque de base (ISO 15854:2005)
Ta slovenski standard je istoveten z: EN ISO 15854:2005
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15854
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS 11.060.10 Supersedes EN ISO 12163:2000, EN ISO 1567:2000
English Version
Dentistry - Casting and baseplate waxes (ISO 15854:2005)
Art dentaire - Cires pour coulée et pour plaque de base Zahnheilkunde - Guss- und Basisplattenwachse (ISO
(ISO 15854:2005) 15854:2005)
This European Standard was approved by CEN on 1 July 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15854:2005: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 15854:2005) has been prepared by Technical Committee ISO/TC 106
"Dentistry" in collaboration with Technical Committee CEN/TC 55 "Dentistry", the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2006, and conflicting national
standards shall be withdrawn at the latest by January 2006.
This document supersedes EN ISO 12163:2000 and EN ISO 1567:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 15854:2005 has been approved by CEN as EN ISO 15854:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 15854
First edition
2005-07-15
Dentistry — Casting and baseplate waxes
Art dentaire — Cires pour coulée et pour plaque de base
Reference number
ISO 15854:2005(E)
©
ISO 2005
ISO 15854:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 15854:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Classification.2
5 Requirements.2
5.1 Appearance.2
5.2 Flow.2
5.3 Behaviour on trimming .2
5.4 Behaviour on softening (Type 1).3
5.5 Appearance after flaming (Type 2).3
5.6 Behaviour on softening (Type 2).3
5.7 Residue on artificial teeth (Type 2) .3
5.8 Behaviour of colouring material (Type 2).3
5.9 Adhesion on storage (Type 2) .3
5.10 Residue on ignition (Type 1).3
5.11 Biocompatibility.3
6 Sampling.3
7 Test methods — General .3
7.1 Ambient temperature.3
7.2 Apparatus function verification.4
8 Test methods — Specific .4
8.1 Visual inspection.4
8.2 Flow.4
8.3 Behaviour on trimming .8
8.4 Behaviour on softening (Type 1).8
8.5 Appearance after flaming (Type 2).8
8.6 Behaviour on softening (Type 2).8
8.7 Residue on artificial teeth and behaviour of colouring material (Type 2).8
8.8 Adhesion on storage (Type 2) .10
8.9 Residue on ignition (Type 1).10
9 Marking and packaging.11
9.1 Marking.11
9.2 Packaging.11
Bibliography .12
ISO 15854:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15854 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 2, Prosthodontic
materials.
This first edition cancels and replaces ISO 1561:1995 and ISO 12163:1999, which have been technically
revised.
iv © ISO 2005 – All rights reserved
ISO 15854:2005(E)
Introduction
This International Standard does not include specific and quantitative requirements for freedom from biological
hazards. It is recommended that, in assessing possible biological or toxicological hazards, reference be made
to ISO 7405 and ISO 10993-1 (see Bibliography).
INTERNATIONAL STANDARD ISO 15854:2005(E)
Dentistry — Casting and baseplate waxes
1 Scope
This International Standard is applicable to dental casting wax and to dental baseplate wax. It specifies the
classification of, and requirements for, dental casting wax and baseplate wax together with the test methods to
be employed to determine compliance with these requirements.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1942-2, Dental vocabulary — Part 2: Dental materials
1)
ISO 3336, Dentistry — Synthetic polymer teeth
1)
ISO 4824, Dentistry — Ceramic denture teeth
ISO 6873, Dental gypsum products
ISO 8601, Data elements and interchange formats — Information interchange — Representation of dates and
times
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1942-2 and the following apply.
3.1
casting wax
mouldable material primarily for shaping patterns in the production of fixed cast restorations using the
“lost-wax” procedure
3.2
baseplate wax
mouldable material primarily for shaping patterns that will be duplicated in denture base polymers, and for
forming occlusion rims and other patterns
1) ISO 3336 and ISO 4824 are to be combined and revised as ISO 22112, Dentistry — Artificial teeth for dental
prostheses.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.