EN ISO 1402:2021
(Main)Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2021)
Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2021)
This document specifies methods for the hydrostatic testing of rubber and plastics hoses and hose assemblies, including methods for the determination of dimensional stability.
Gummi- und Kunststoffschläuche und Schlauchleitungen - Hydrostatische Prüfung (ISO 1402:2021)
Dieses Dokument legt Verfahren für die hydrostatische Prüfung von Gummi- und Kunststoffschläuchen und Schlauchleitungen und darunter Verfahren zur Bestimmung der Maßstabilität fest.
Tuyaux et flexibles en caoutchouc et en plastique - Essais hydrostatiques (ISO 1402:2021)
Le présent document spécifie des méthodes d'essais hydrostatiques pour les tuyaux et flexibles en caoutchouc et en plastique, y compris des méthodes de détermination de la stabilité dimensionnelle.
Gumene in polimerne cevi ter cevni priključki - Hidrostatično preskušanje (ISO 1402:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2021
Nadomešča:
SIST EN ISO 1402:2010
Gumene in polimerne cevi ter cevni priključki - Hidrostatično preskušanje (ISO
1402:2021)
Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2021)
Gummi- und Kunststoffschläuche und Schlauchleitungen - Hydrostatische Prüfung (ISO
1402:2021)
Tuyaux et flexibles en caoutchouc et en plastique - Essais hydrostatiques (ISO
1402:2021)
Ta slovenski standard je istoveten z: EN ISO 1402:2021
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 1402
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2021
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 1402:2009
English Version
Rubber and plastics hoses and hose assemblies -
Hydrostatic testing (ISO 1402:2021)
Tuyaux et flexibles en caoutchouc et en plastique - Gummi- und Kunststoffschläuche und
Essais hydrostatiques (ISO 1402:2021) Schlauchleitungen - Hydrostatische Prüfung (ISO
1402:2021)
This European Standard was approved by CEN on 20 April 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1402:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 1402:2021) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by November 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1402:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1402:2021 has been approved by CEN as EN ISO 1402:2021 without any modification.
INTERNATIONAL ISO
STANDARD 1402
Fifth edition
2021-04
Rubber and plastics hoses and hose
assemblies — Hydrostatic testing
Tuyaux et flexibles en caoutchouc et en plastique — Essais
hydrostatiques
Reference number
ISO 1402:2021(E)
©
ISO 2021
ISO 1402:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 1402:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Apparatus . 1
6 Test pieces . 2
6.1 Hose assemblies . 2
6.2 Hoses . 2
6.3 Number of test pieces . 2
7 Application of hydrostatic pressure . 2
7.1 General . 2
7.2 Procedure . 2
8 Hydrostatic pressure tests . 2
8.1 Proof pressure hold test . 2
8.2 Measurement of deformation under pressure . 3
8.2.1 General procedure . 3
8.2.2 Change in length at the specified test pressure . 3
8.2.3 Change in external diameter at the specified test pressure, measured at
the approximate middle of the hose assembly . 4
8.2.4 Twisting at the specified test pressure . 5
8.2.5 Warping at the specified test pressure . 5
8.3 Burst pressure test . 5
8.4 Leakage test . 6
8.4.1 Test pieces . 6
8.4.2 Procedure . 6
8.4.3 Criteria for failure . 6
9 Test report . 6
Bibliography . 9
ISO 1402:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Rubber and plastics hoses and hose assemblies, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 218, Rubber and plastics hoses and
hose assemblies, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fifth edition cancels and replaces the fourth edition (ISO 1402:2009), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the tolerances of the pressure in Figure 3, 7.2.2, 8.1 and 8.2 have been revised;
— the description of the failure mode in 8.3 has been revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
INTERNATIONAL STANDARD ISO 1402:2021(E)
Rubber and plastics hoses and hose assemblies —
Hydrostatic testing
1 Scope
This document specifies methods for the hydrostatic testing of rubber and plastics hoses and hose
assemblies, including methods for the determination of dimensional stability.
2 Normative references
The following documents are referred to in the text in such a way that so
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.