Powered industrial trucks - Visibility - Test methods and verification - Part 5: Industrial variable-reach trucks greater than 10 000 kg capacity

This document specifies the requirements and test procedures for 360° visibility of sit on self-propelled industrial variable-reach trucks (herein after referred to as trucks) without a load, with a capacity greater than 10 000 kg in accordance with ISO 5053-1. It is intended be used in conjunction with EN 16842 1.
Where specific requirements in this part are modified from the general requirements in EN 16842-1, the requirements of this part are truck specific and to be used for sit-on self-propelled industrial variable-reach trucks with a capacity greater than 10 000 kg.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events, relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not deal with rough-terrain variable-reach trucks (see EN 15830).

Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil 5: Flurförderzeuge mit veränderlicher Reichweite mit einer Nenntragfähigkeit größer 10 000 kg

Dieses Dokument legt die Anforderungen und Prüfverfahren für die Rundumsicht (360°) von motorkraftbetriebenen Flurförderzeugen mit Fahrersitz mit veränderlicher Reichweite (im Folgenden als Flurförderzeuge bezeichnet) ohne Last, mit einer Nenntragfähigkeit größer 10 000 kg in Übereinstimmung mit ISO 5053 1 fest. Es ist dafür vorgesehen, in Verbindung mit EN 16842 1 angewendet zu werden.
Wenn spezifische Anforderungen in diesem Teil von den allgemeinen Anforderungen in EN 16842 1 abweichen, sind die Anforderungen in diesem Teil für das Flurförderzeug spezifisch und für motorkraftbetriebene Flurförderzeuge mit Fahrersitz mit veränderlicher Reichweite mit einer Nenntragfähigkeit größer 10 000 kg anzuwenden.
Dieser Teil von EN 16842 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse, die für die Sichtverhältnisse des Bedieners der betreffenden Maschinen relevant sind, wenn sie bestimmungsgemäß und unter Bedingungen, die vom Hersteller als Fehlanwendung vernünftigerweise vorhersehbar sind, verwendet werden.
Dieses Dokument behandelt nicht geländegängige Stapler mit veränderlicher Reichweite (siehe EN 15830).

Chariots de manutention automoteurs - Visibilité - Méthodes d'essai et vérification - Partie 5 : Chariots de manutention à portée variable ayant une capacité supérieure à 10 000 kg

Le présent document spécifie les prescriptions et les modes opératoires pour la visibilité sur 360° des chariots de manutention automoteurs à portée variable à conducteur assis (ci-après désignés chariots) sans charge, ayant une capacité supérieure à 10 000 kg conformes à l'ISO 5053-1. Il est destiné à être utilisé conjointement avec l'EN 16842-1.
Lorsque des prescriptions spécifiques de la présente partie sont modifiées par rapport aux prescriptions générales de l'EN 16842-1, les prescriptions de la présente partie sont spécifiques au chariot et sont à utiliser pour les chariots de manutention automoteurs à portée variable à conducteur assis ayant une capacité supérieure à 10 000 kg.
La présente partie de l'EN 16842 traite de tous les phénomènes dangereux, situations dangereuses ou événements dangereux significatifs relatifs à la visibilité de l’opérateur pour les machines concernées lorsqu'elles sont utilisées comme prévu et dans des conditions de mauvaise utilisation raisonnablement prévisible par le fabricant.
Le présent document ne traite pas des chariots tout-terrain à portée variable (voir l'EN 15830).

Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika - Preskusne metode in preverjanje - 5. del: Vozila za talni transport s spremenljivim dosegom in z zmogljivostjo, večjo od 10 000 kg

General Information

Status
Published
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
13-Jan-2021
Completion Date
13-Jan-2021

Buy Standard

Standard
EN 16842-5:2021
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 16842-5:2021
01-april-2021

Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika -

Preskusne metode in preverjanje - 5. del: Vozila za talni transport s spremenljivim

dosegom in z zmogljivostjo, večjo od 10 000 kg

Powered industrial trucks - Visibility - test methods and verification - Part 5: Industrial

variable-reach trucks greater than 10 000 kg capacity

Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil

5: Flurförderzeuge mit veränderlicher Reichweite mit einer Nenntragfähigkeit größer 10

000 kg

Chariots de manutention - Visibilité - Méthode d'essai pour la vérification - Partie 5 :

Chariots de manutention à portée variable ayant une capacité supérieure à 10 000 kg

Ta slovenski standard je istoveten z: EN 16842-5:2021
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 16842-5:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 16842-5:2021
---------------------- Page: 2 ----------------------
SIST EN 16842-5:2021
EN 16842-5
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2021
EUROPÄISCHE NORM
ICS 53.060
English Version
Powered industrial trucks - Visibility - Test methods and
verification - Part 5: Industrial variable-reach trucks
greater than 10 000 kg capacity

Chariots de manutention automoteurs - Visibilité - Kraftbetriebene Flurförderzeuge - Sichtverhältnisse -

Méthodes d'essai et vérification - Partie 5 : Chariots de Prüfverfahren und Verifikation - Teil 5:

manutention à portée variable ayant une capacité Flurförderzeuge mit veränderlicher Reichweite mit

supérieure à 10 000 kg einer Nenntragfähigkeit größer 10 000 kg
This European Standard was approved by CEN on 6 December 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16842-5:2021 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16842-5:2021
EN 16842-5:2021 (E)
Contents Page

European foreword ...................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 5

1 Scope .................................................................................................................................................................... 6

2 Normative references .................................................................................................................................... 6

3 Terms and definitions ................................................................................................................................... 6

4 Truck configuration ....................................................................................................................................... 6

4.1 General................................................................................................................................................................ 6

4.2 Height of load carrying surface .................................................................................................................. 6

4.3 Fork arm dimension ...................................................................................................................................... 7

4.4 Retractable lift boom position ................................................................................................................... 7

5 Test equipment ................................................................................................................................................ 7

6 Test procedures for direct visibility ........................................................................................................ 7

6.1 Lighting equipment position ...................................................................................................................... 7

6.2 Test paths for industrial variable reach trucks > 10 000 kg capacity ......................................... 8

6.3 Measurement procedure .............................................................................................................................. 9

6.4 Test procedure for indirect visibility ................................................................................................... 10

7 Acceptance criteria...................................................................................................................................... 10

7.1 General............................................................................................................................................................. 10

7.2 Direct visibility ............................................................................................................................................. 10

7.3 Indirect visibility .......................................................................................................................................... 10

7.4 Criteria for industrial variable-reach trucks greater than 10 000 kg rated capacity ......... 11

8 Test report ...................................................................................................................................................... 12

9 Information for use ..................................................................................................................................... 12

---------------------- Page: 4 ----------------------
SIST EN 16842-5:2021
EN 16842-5:2021 (E)
European foreword

This document (EN 16842-5:2021) has been prepared by Technical Committee CEN/TC 150 “Industrial

trucks – Safety”, the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be

withdrawn at the latest by July 2021.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document is intended to be used in combination with the requirements in EN 16842-1.

The EN 16842 series consists of the following parts under the general title “Powered industrial trucks –

Visibility – Test methods and verification”:
— Part 1: General requirements;

— Part 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including 10 000 kg

capacity;
— Part 3: Reach trucks up to and including 10 000 kg capacity;

— Part 4: Industrial variable reach trucks up to and including 10 000 kg capacity;

— Part 5: Industrial variable reach trucks greater than 10 000 kg capacity;

— Part 6: Sit-on counterbalance trucks and rough terrain masted trucks greater than 10 000 kg capacity;

— Part 7: Variable reach and masted container trucks handling freight containers of 6 m (20 ft) length

and longer;
— Part 8: Stand on counterbalance trucks up to and including 10 000 kg capacity;

— Part 9: Order picking lateral- and front stacking trucks with elevating operator position;

— Part 10: Towing and Pushing tractors and Burden carrier.
It is intended to develop the parts related to the following machinery:
— Pallet stacking trucks (rider controlled);
— Single side loader;
— Multi-directional forklift truck;
— Articulated counterbalance lift truck;
— Non-stacking low-lift straddle carrier (as defined in ISO 5053-1:2020, 3.18);
— Stacking high-lift straddle carrier (as defined in ISO 5053-1:2020, 3.19).
---------------------- Page: 5 ----------------------
SIST EN 16842-5:2021
EN 16842-5:2021 (E)

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North

Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

Kingdom.
---------------------- Page: 6 ----------------------
SIST EN 16842-5:2021
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.