iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN IEC 61300-2-11:2024

(Main)

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression

IEC 61300-2-11:2023 is available as IEC 61300-2-11:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61300-2-11:2023 is to ensure that the captivation or the attachment of the cable to the fibre optic devices or components, for example fibre optic closures, will withstand compressive axial loads likely to be applied during normal service. This third edition cancels and replaces the second edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) added Terms and definitions clause; b) removed severity table for closures; c) added recommended severity for tubes and cables without strength member attachment.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-11: Prüfungen - Axialer Druck

Dispositifs d'interconnexion et composants passifs fibroniques - Procédures fondamentales d'essais et de mesures - Partie 2-11: Essais - Compression axiale

IEC 61300-2-11:2023 est disponible sous forme de IEC 61300-2-11:2023 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61300-2-11:2023 vise à vérifier que la rétention ou la fixation du câble à des dispositifs ou des composants fibroniques, par exemple boîtiers fibroniques, résistera aux forces de compression axiale susceptibles d'être appliquées dans des conditions normales de fonctionnement. Cette troisième édition annule et remplace la deuxième édition parue en 2012. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) ajout d’un article "Termes et définitions"; b) suppression du tableau des sévérités pour les boîtiers; c) ajout d'une recommandation de sévérité pour les tubes et les câbles sans fixation d'éléments de renfort.

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-11. del: Preskusi - Osni pritisk (IEC 61300-2-11:2023)

Namen tega dela standarda IEC 61300 je zagotoviti, da bo trdnost pritrditve kabla na napravo ali komponenta z optičnimi vlakni zdržala tlačno osno obremenitev, ki se lahko pojavi med običajnim delovanjem.

General Information

Status
Published
Publication Date
11-Jan-2024
ICS
33.180.20 - Fibre optic interconnecting devices
Technical Committee
CLC/TC 86BXA - Fibre optic interconnect, passive and connectorised components
Drafting Committee
IEC/SC 86B - IEC_SC_86B
Current Stage
6060 - Document made available - Publishing
Start Date
12-Jan-2024
Due Date
28-Jun-2024
Completion Date
12-Jan-2024
Ref Project
SIST EN IEC 61300-2-11:2024 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression (IEC 61300-2-11:2023)

Relations

Replaces
EN 61300-2-11:2013 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression
Effective Date
23-Jan-2023

Buy Standard

EN IEC 61300-2-11:2024EN IEC 61300-2-11:2024
PreviousNext
Standard
EN IEC 61300-2-11:2024
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61300-2-11:2024
01-marec-2024
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-11. del: Preskusi - Osni pritisk (IEC 61300-2-11:2023)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-11: Tests - Axial compression (IEC 61300-2-11:2023)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-11: Prüfungen - Axialer Druck (IEC 61300-2-11:2023)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 2-11: Essais - Compression axiale (IEC
61300-2-11:2023)
Ta slovenski standard je istoveten z: EN IEC 61300-2-11:2024
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61300-2-11:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61300-2-11:2024

---------------------- Page: 2 ----------------------
SIST EN IEC 61300-2-11:2024


EUROPEAN STANDARD EN IEC 61300-2-11

NORME EUROPÉENNE

EUROPÄISCHE NORM January 2024
ICS 33.180.20 Supersedes EN 61300-2-11:2013
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-11: Tests -
Axial compression
(IEC 61300-2-11:2023)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-11: Essais - Compression axiale 11: Prüfungen - Axialer Druck
(IEC 61300-2-11:2023) (IEC 61300-2-11:2023)
This European Standard was approved by CENELEC on 2023-12-29. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61300-2-11:2024 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61300-2-11:2024
EN IEC 61300-2-11:2024 (E)
European foreword
The text of document 86B/4807/FDIS, future edition 3 of IEC 61300-2-11, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-11:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-09-29
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-12-29
document have to be withdrawn

This document supersedes EN 61300-2-11:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61300-2-11:2023 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 61753 (series) NOTE Approved as EN 61753 (series)
IEC 62005 (series) NOTE Approved as EN IEC 62005 (series)
2

-------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61300-2-44:2024(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-44: Tests - Flexing of the strain relief of fibre optic devices and components
SIST EN IEC 61300-2-44:2024

IEC 61300-2-44:2024 specifies a test to determine the influence of flexing under tensile load of the strain relief of fibre optic interconnecting devices or components. The intention is to simulate the number of flexing cycles which would typically be experienced during service life. This test is applied to both single fibre cable and multiple fibre cable. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) replaced active monitoring with transient loss for measurements during test; b) harmonized recommended severities according to IEC 61753-1.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-2-6:2024(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism
SIST EN IEC 61300-2-6:2024

IEC 61300-2-6:2023 is available as IEC 61300-2-6:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61300-2-6:2023 describes a test to ensure the coupling mechanism of a connector set or connector and device combination withstands the axial loads likely to be applied during normal service, and that the optical performance remains within the given specifications during this test. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of normative references; b) modification of the details to be specified; c) addition of optical monitoring.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61753-021-06:2023(Main)
Fibre optic interconnecting devices and passive components - Performance standard - Part 021-06: Single-mode fibre optic connectors terminated as pigtails and patchcords for category OP+ – Extended outdoor protected environment
SIST EN IEC 61753-021-06:2024

IEC 61753-021-06:2023 defines the minimum initial test and measurement requirements and severities which single-mode fibre optic connectors terminated as a pigtail or a patchcord satisfy in order to be categorised as meeting the IEC standard category OP+ (extended outdoor protected environment), as defined in IEC 61753-1. If tests were performed on the connectors terminated as pigtails or patchcords for category OP+HD and the product passed, the product will be automatically qualified or categorized as meeting the IEC standard for category OP+. If tests are performed on the connectors terminated as pigtails or patchcords for category OP+, and the product passes, the product will be automatically qualified or categorized as meeting the IEC standard for categories OP and C. This first edition cancels and replaces the first edition of IEC 61753-021-6 published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 61753-021-6:2007: a) updated environmental category (from O to OP+), tests and their severities according to IEC 61753-1:2018; b) removed the copyright notice as it is no longer needed; c) changed title and scope to remove restrictions on attenuation and return loss grades; d) changed the term and definitions of the different types of test samples (pigtail test samples and patchcord test samples) used in the various tests to avoid confusion; e) removed the term and definition for small form factor (SFF) connectors as it is no longer used in the document; f) updated fibre naming conventions according to IEC 60793-2-50: and added provisions for B-657 fibres; g) added all the attenuation and return loss grades defined in IEC 61753-1; h) removed the static side load test; i) removed the need to perform all tests sequentially to align with other performance standards; j) added provisions for rectangular ferrule connectors; k) added Annex B for visual examination of the outer cable sheath movement of reinforced cables as an additional requirement for change of temperature, cable retention and flexing of the strain relief tests.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61753-021-02:2023(Main)
Fibre optic interconnecting devices and passive components - Performance standard - Part 021-02: Single-mode fibre optic connectors terminated as pigtails and patchcords for category C - Controlled environment
SIST EN IEC 61753-021-02:2024

IEC 61753-021-02:2023 defines the minimum initial test and measurement requirements and severities which single-mode fibre optic connectors terminated as a pigtail or a patchcord satisfy in order to be categorized as meeting the IEC standard category C (controlled environment), as defined in IEC 61753-1. If tests were performed on the connectors terminated as pigtails or patchcords for categories OP+HD, OP+, OP, OPHD, or CHD and the product passed, the product will be automatically qualified or categorized as meeting the IEC standard for category C. This first edition cancels and replaces the second edition of IEC 61753-021-2 published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 61753-021-2:2007: a) changed scope to remove restrictions on attenuation and return loss grades; b) included provisions for rectangular ferrule connectors; c) changed the terms and definitions of the different types of test samples (pigtail test samples and patchcord test samples) used in the various tests to avoid confusion; d) updated fibre naming conventions according to IEC 60793-2-50 and added provisions for B-657 fibres; e) added all the attenuation and return loss grades defined in IEC 61753-1; f) test severities updated according to IEC 61753-1; g) reduced flexing of strain relief cycles from 100 cycles to 50 cycles; h) added the torsion test; i) reduced the duration of the fibre/cable retention test on reinforced cables from 120 s to 60 s minimum; j) removed the static side load test; k) reduced the number of mating durability cycles from 500 cycles to 200 cycles and added provisions for rectangular ferrule connectors; l) added Annex B for visual examination of the outer cable sheath movement of reinforced cables as an additional requirement for change of temperature, cable retention and flexing of the strain relief tests.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-2-38:2023(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-38: Tests - Sealing for fibre optic sealed closures and hardened connectors using air pressure
SIST EN IEC 61300-2-38:2024

IEC 61300-2-38:2023 is available as IEC 61300-2-38:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61300-3-38:2023 presents two methods for testing the sealing performance of a fibre optic sealed closure and hardened connector using air pressure. This third edition cancels and replaces the second edition published in 2006. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of sealed hardened connectors; b) recommended test severities from IEC 61753-1; c) test configurations for hardened connectors and adaptors.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-2-26:2023(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-26: Tests - Salt mist
SIST EN IEC 61300-2-26:2023

IEC 61300-2-26: 2023 provides a test to determine the corrosion resistance of the metals used in the construction of fibre optic interconnecting devices and passive components. This document determines if dissimilar metals have been well finished to prevent corrosion. The requirements of the tests for these devices are defined in IEC 61753-1. This third edition cancels and replaces the second edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of Clause 3, Terms and definitions; b) harmonisation with IEC 61753-1:2018 and addition of Table 2; c) harmonisation with IEC 60068-2-11:2021

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-3-45:2023(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-45: Examinations and measurements - Attenuation of random mated multi-fibre connectors
SIST EN IEC 61300-3-45:2023

IEC 61300-3-45:2023 is available as IEC 61300-3-45:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61000-3-45:2023 describes the procedure required to measure the statistical distribution and mean attenuation for random mated optical connectors with physical contact (PC) and angled physical contact (APC) polished multi-fibre rectangular ferrules as defined in the IEC 61754 series. This measurement method is applicable to cable assemblies. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of sample size for > 12-fibre connector measurement; b) inclusion of guidance for multimode measurement.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50411-3-2:2023(Main)
Fibre management systems and protective housings to be used in optical fibre communication systems - Product specifications - Part 3-2: Single-mode mechanical fibre splice
SIST EN 50411-3-2:2023

1.1 Product definition This document contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements, which single mode mechanical splice needs to meet in order for it to be categorized as a European standard product. Although, in this document, the product is qualified for EN IEC 60793 2 50 type B-652.D single mode fibres, it is also suitable for mechanical splicing of other single mode fibres with 125 µm diameter glass cladding. Also mechanical splices designed for connections of buffered or secondary coated fibres and cords according to EN 60794 2 50:2008 are covered by this document. 1.2 Interoperability The installed mechanical splice fits into optical fibre management system with optical splice cassettes or splice trays as defined in EN IEC 61756 1. This document specifies the following two physical interface dimensions: - cross sectional profile with width, height or diameter (in millimetres); - length (in millimetres). 1.3 Expected performance In this document, the performance of the mechanical splice is given with identical fibres only as specified in Annex A. Losses associated with tolerances in fibre cladding diameter and mode field mismatch are not taken into account. The measured attenuation is a function of the core concentricity, cladding non-circularity and alignment capability. The optical return loss performance is a function of the index matching gel and the fibre end face preparation. 1.4 Operating environment The tests selected combined with the severities and durations are representative of an outdoor enclosed environment defined as category OP in EN IEC 61753 1. To ensure that the product can be used in outdoor closures, boxes or street cabinets for categories A, G or S (as defined in EN IEC 61753 1) the specified lower temperature is extended to −40 °C and a water immersion requirement for temporary flooding conditions has been added. 1.5 Reliability Whilst the anticipated service life expectancy of the product in this environment is at least 20 years, compliance with this document does not guarantee the reliability of the product. This is expected to be predicted using a recognized reliability assessment programme. 1.6 Quality assurance Compliance with this document does not guarantee the manufacturing consistency of the product. This is expected to be maintained using a recognized quality assurance programme.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-3-4:2023/AC:2023-07(Corrigendum)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation
SIST EN IEC 61300-3-4:2023/AC:2023
  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-3-53:2021/AC:2023-07(Corrigendum)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-53: Examinations and measurements - Encircled angular flux (EAF) measurement method based on two-dimensional far field data from multimode waveguide (including fibre)
SIST EN IEC 61300-3-53:2021/AC:2023
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day