EN IEC 62841-3-7:2021
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
IEC 62841-3-7:2020 This document applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to transportable wall saws that are intended to be left unattended while performing an operation. This document does not apply to transportable wall saws that employ hydraulic systems. This document does not apply to hand-held cut-off machines.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-7: Besondere Anforderungen für transportable Wandsägen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-7: Exigences particulières pour les scies murales portables
IEC 62841-3-7:2020 Le présent document s'applique aux scies murales portables guidées par un système de guidage de piste, destinées à couper à sec ou à être raccordées à un système liquide pour couper du béton, de la pierre ou un matériau similaire au moyen d'une meule diamant. La vitesse assignée de la meule diamant ne dépasse pas une vitesse périphérique de 100 m/s à la capacité assignée. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. Le présent document ne s’applique pas aux scies murales portables qui sont destinées à être laissées sans surveillance pendant l’exécution d’une manœuvre. Le présent document ne s’applique pas aux scies murales portables qui utilisent des systèmes hydrauliques. Le présent document ne s'applique pas aux machines à tronçonner portatives.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-7. del: Posebne zahteve za premične stenske žage
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62841-3-7:2021
01-julij-2021
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
7. del: Posebne zahteve za premične stenske žage
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit – Teil 3-7: Besondere Anforderungen für
transportable Wandsägen
Ta slovenski standard je istoveten z: EN IEC 62841-3-7:2021
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
SIST EN IEC 62841-3-7:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62841-3-7:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 62841-3-7:2021
EUROPEAN STANDARD EN IEC 62841-3-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2021
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-7: Particular
requirements for transportable wall saws
(IEC 62841-3-7:2020)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-7: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies murales portables Gartenmaschinen - Sicherheit - Teil 3-7: Besondere
(IEC 62841-3-7:2020) Anforderungen für transportable Wandsägen
(IEC 62841-3-7:2020)
This European Standard was approved by CENELEC on 2020-07-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62841-3-7:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62841-3-7:2021
EN IEC 62841-3-7:2021 (E)
European foreword
The text of document 116/455/FDIS, future edition 1 of IEC 62841-3-7, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-3-7:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-04-26
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-04-26
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of
EN IEC 62841-3-7:2021/A11:2021.
Endorsement notice
The text of the International Standard IEC 62841-3-7:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 11203:1995 NOTE Harmonized as EN ISO 11203:2009 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62841-3-7:2021
IEC 62841-3-7
®
Edition 1.0 2020-06
INTERNATIONAL
STANDARD
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.