EN 62496-2-1:2011
(Main)Optical circuit boards - Part 2-1: Measurements - Optical attenuation and isolation
Optical circuit boards - Part 2-1: Measurements - Optical attenuation and isolation
IEC 62496-2-1:2011 describes the various methods to measure the optical attenuation and isolation of optical circuit boards (OCBs).
Optische Leiterplatten - Teil 2-1: Messungen - Optische Dämpfung und Isolation
Cartes à circuits optiques - Partie 2-1: Mesures - Affaiblissement et isolation optiques
la CEI 62496-2-1:2011 décrit les différentes méthodes utilisées pour mesurer l'affaiblissement et l'isolation optiques des cartes à circuits optiques (OCB, Optical Circuit Boards).
Plošče z optičnimi vezji - 2-1. del: Meritve - Optično slabljenje in izolacija (IEC 62496-2-1:2011)
IEC 62496-2-1 opisuje različne metode za merjenje optičnega slabljenja in izolacije plošč z optičnimi vezji (OCB).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
3ORãþH]RSWLþQLPLYH]MLGHO0HULWYH2SWLþQRVODEOMHQMHLQL]RODFLMD,(&
Optical circuit boards - Part 2-1: Measurements - Optical attenuation and isolation (IEC
62496-2-1:2011)
Optische Leiterplatten - Teil 2-1: Messungen - Optische Dämpfung und Isolation (IEC
62496-2-1:2011)
Cartes à circuits optiques - Partie 2-1: Mesures - Affaiblissement et isolation optiques
(CEI 62496-2-1:2011)
Ta slovenski standard je istoveten z: EN 62496-2-1:2011
ICS:
31.180 7LVNDQDYH]MD7,9LQWLVNDQH Printed circuits and boards
SORãþH
33.180.01 6LVWHPL]RSWLþQLPLYODNQLQD Fibre optic systems in
VSORãQR general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 62496-2-1
NORME EUROPÉENNE
September 2011
EUROPÄISCHE NORM
ICS 33.180.01
English version
Optical circuit boards -
Part 2-1: Measurements -
Optical attenuation and isolation
(IEC 62496-2-1:2011)
Cartes à circuits optiques - Optische Leiterplatten -
Partie 2-1: Mesures - Teil 2-1: Messungen -
Affaiblissement et isolation optiques Optische Dämpfung und Isolation
(CEI 62496-2-1:2011) (IEC 62496-2-1:2011)
This European Standard was approved by CENELEC on 2011-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62496-2-1:2011 E
Foreword
The text of document (86/396/FDIS), future edition 1 of IEC 62496-2-1, prepared by IEC TC 86, "Fibre
optics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2012-06-01
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2014-09-01
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62496-2-1:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60793-1-1 NOTE Harmonized as EN 60793-1-1.
IEC 60794-1-1 NOTE Harmonized as EN 60794-1-1.
IEC 61280-4-1 NOTE Harmonized as EN 61280-4-1.
IEC 61300-3-35 NOTE Harmonized as EN 61300-3-35.
- 3 - EN 62496-2-1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60793-2-10 - Optical fibres - EN 60793-2-10 -
Part 2-10: Product specifications - Sectional
specification for category A1 multimode fibres
IEC 60793-2-50 - Optical fibres - EN 60793-2-50 -
Part 2-50: Product specifications - Sectional
specification for class B single-mode fibres
IEC 60825-1 - Safety of laser products - EN 60825-1 -
Part 1: Equipment classification and
requirements
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-3-1 2005 Fibre optic interconnecting devices and EN 61300-3-1 2005
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination
IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -
Part 3-4: Examinations and measurements -
Attenuation
IEC 62496-1 2008 Optical circuit boards - EN 62496-1 2009
Part 1: General
IEC 62614 - Fibre optics - Launch condition requirements EN 62614 -
for measuring multimode attenuation
ISO 3599 - Vernier callipers reading to 0,1 and 0,05 mm - -
ISO 6906 - Vernier callipers reading to 0,02 mm - -
IEC 62496-2-1 ®
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical circuit boards –
Part 2-1: Measurements – Optical attenuation and isolation
Cartes à circuits optiques –
Partie 2-1: Mesures – Affaiblissement et isolation optiques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX V
ICS 33.180.01 ISBN 978-2-88912-572-2
– 2 – 62496-2-1 © IEC:2011
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Precautions . 6
4 Apparatus . 7
4.1 Launch conditions and source (S) . 7
4.2 Power-meter (D) . 7
4.3 Optical fibre (OF) . 8
4.4 Mode filter (MF) . 8
4.5 Optical direction changing device (OD) . 9
4.6 Temporary joint (TJ) . 9
5 Procedure . 10
5.1 Pre-conditioning . 10
5.2 Visual inspection . 11
5.3 Connectivity inspection . 11
5.4 OCB configurations and measurement methods . 11
5.5 Attenuation measurement with a power-meter . 13
5.5.1 General . 13
5.5.2 Cut-back method . 13
5.5.3 Insertion method (A) . 15
5.5.4 Insertion method (B) . 23
5.6 Isolation measurement with a power-meter . 25
5.6.1 Insertion method (C) . 26
5.6.2 Insertion method (D) . 31
5.7 Mirror loss measurement . 32
6 Details to be specified . 33
Bibliography . 34
Figure 1 – Launch apparatus for butt-joint connection, (a) without OD, (b) with OD . 10
Figure 2 – Cut-back method – Configuration A . 14
Figure 3 – Cut-back method – Configuration B . 15
Figure 4 – Insertion method (A) – Configuration A . 16
Figure 5 – Insertion method (A), multi port sequential measurements – Configuration A . 17
Figure 6 – Insertion method (A) – Configuration B . 18
Figure 7 – Insertion method (A) – Configuration C-1 . 19
Figure 8 – Insertion method (A) – Configuration C-2 . 20
Figure 9 – Insertion method (A) – Configuration D . 21
Figure 10 – Insertion method (A) – Configuration E . 22
Figure 11 – Insertion method (A) – Configuration E . 23
Figure 12 – Insertion method (B) – Configuration A . 24
Figure 13 – Insertion method (B) – Configuration C-1 . 25
Figure 14 – Insertion method (C) – Configuration A . 26
Figure 15 – Insertion method (C) – Configuration B . 27
Figure 16 – Insertion method (C) – Configuration C-1 . 28
62496-2-1 © IEC:2011 – 3 –
Figure 17 – Insertion method (C) – Configuration D . 29
Figure 18 – Insertion method (C) – Configuration E . 30
Figure 19 – Insertion method (C) – Configuration E . 31
Figure 20 – Insertion method (D) – Configuration A . 32
Figure 21 – Mirror loss measurement . 33
Table 1 – Preferred source and launch conditions . 7
Table 2 – Preferred launching and receiving fibres . 8
Table 3 – Measurement methods of attenuations . 11
Table 4 – Measurement methods of isolations . 12
– 4 – 62496-2-1 © IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL CIRCUIT BOARDS –
Part 2-1: Measurements –
Optical attenuation and isolation
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has repr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.