iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61291-2:2012

(Main)

Optical amplifiers - Part 2: Digital applications - Performance specification template

Optical amplifiers - Part 2: Digital applications - Performance specification template

IEC 61291-2:2012 applies to single channel optical amplifier (OA) devices to be used in digital applications. For multichannel applications, use IEC 61291, Part 4. The object of this performance specification template is to provide a frame for the preparation of detail specifications on the performances of single channel OA devices to be used in digital applications. This edition constitutes a minor update through clarification that the scope is for single channel optical amplifiers, and that pump leakage parameters do not apply to semiconductor optical amplifiers.

Lichtwellenleiter-Verstärker - Teil 2: Digitale Anwendungen - Vorlage für Betriebsverhaltensspezifikationen

Amplificateurs optiques - Partie 2: Applications numériques - Modèles de spécifications de performances

La CEI 61291-2:2012 s'applique aux dispositifs amplificateurs optiques (AO) à un seul canal, destinés à être utilisés dans le cadre d'applications numériques. Pour les applications multicanaux, utiliser la CEI 61291, Partie 4. L'objet de ce modèle de spécifications de performances est de fournir une trame de préparation de spécifications particulières relatives aux performances des dispositifs AO à un seul canal destinés à être utilisés dans le cadre d'applications numériques. Cette édition constitue une mise à jour mineure, consistant en une clarification du domaine d'application, mentionnant uniquement les amplificateurs optiques pour un seul canal, et les paramètres de fuite de pompage ne s'appliquent pas aux amplificateurs optiques à semiconducteurs.

Optični ojačevalniki - 2. del: Digitalne aplikacije - Specifikacijska predloga delovanja (IEC 61291-2:2012)

Ta specifikacijska predloga delovanja se uporablja za naprave z enokanalnim optičnim ojačevalnikom (OA), ki se uporabljajo za digitalne aplikacije. Za večkanalne aplikacije se uporablja standard IEC 61291, del 4. Cilj te specifikacijske predloge delovanja je zagotoviti okvir za pripravo podrobnih specifikacij za delovanje naprav z enokanalnim optičnim ojačevalnikom, ki se uporabljajo za digitalne aplikacije. Avtorji podrobne specifikacije lahko dodajo specifikacijske parametre in/ali skupine specifikacijskih parametrov za določene aplikacije. Vendar avtorji podrobnih specifikacij ne smejo odstraniti specifikacijskih parametrov, določenih v tem standardu.

General Information

Status
Withdrawn
Publication Date
08-Mar-2012
Withdrawal Date
13-Feb-2015
ICS
33.180.30 - Optic amplifiers
Technical Committee
CLC/SR 86C - Fibre optic systems and active devices
Drafting Committee
IEC/SC 86C - IEC_SC_86C
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
24-Mar-2019
Completion Date
24-Mar-2019
Ref Project
SIST EN 61291-2:2012 - Optical amplifiers - Part 2: Digital applications - Performance specification template (IEC 61291-2:2012)

Relations

Replaces
EN 61291-2:2007 - Optical amplifiers - Part 2: Digital applications - Performance specification template
Effective Date
29-Jan-2023
Replaced By
EN 61291-2:2016 - Optical amplifiers - Part 2: Single channel applications - Performance specification template
Effective Date
07-Jun-2016

Buy Standard

EN 61291-2:2012EN 61291-2:2012
PreviousNext
Standard
EN 61291-2:2012
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61291-2:2012
01-maj-2012
1DGRPHãþD
SIST EN 61291-2:2007
2SWLþQLRMDþHYDOQLNLGHO'LJLWDOQHDSOLNDFLMH6SHFLILNDFLMVNDSUHGORJD
GHORYDQMD ,(&
Optical amplifiers - Part 2: Digital applications - Performance specification template (IEC
61291-2:2012)
Lichtwellenleiter-Verstärker - Teil 2: Digitale Anwendungen - Vorlage für
Betriebsverhaltensspezifikationen (IEC 61291-2:2012)
Amplificateurs optiques - Partie 2: Applications numériques - Modèles de spécifications
de performances (CEI 61291-2:2012)
Ta slovenski standard je istoveten z: EN 61291-2:2012
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
SIST EN 61291-2:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61291-2:2012

---------------------- Page: 2 ----------------------

SIST EN 61291-2:2012

EUROPEAN STANDARD
EN 61291-2

NORME EUROPÉENNE
March 2012
EUROPÄISCHE NORM

ICS 33.180.30 Supersedes EN 61291-2:2007


English version


Optical amplifiers -
Part 2: Digital applications -
Performance specification template
(IEC 61291-2:2012)


Amplificateurs optiques -  Lichtwellenleiter-Verstärker -
Partie 2: Applications numériques - Teil 2: Digitale Anwendungen -
Modèles de spécifications de Vorlage für
performances Betriebsverhaltensspezifikationen
(CEI 61291-2:2012) (IEC 61291-2:2012)





This European Standard was approved by CENELEC on 2012-02-14. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61291-2:2012 E

---------------------- Page: 3 ----------------------

SIST EN 61291-2:2012
EN 61291-2:2012 - 2 -

Foreword
The text of document 86C/1018/CDV, future edition 3 of IEC 61291-2, prepared by SC 86C, "Fibre optic
systems and active devices", of IEC TC 86, "Fibre optics" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 61291-2:2012.

The following dates are fixed:
(dop) 2012-11-14
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-02-14

standards conflicting with the
document have to be withdrawn

This document supersedes EN 61291-2:2007.
EN 61291-2:2012 constitutes a minor update through clarification that the scope is for single channel
optical amplifiers, and that pump leakage parameters do not apply to semiconductor optical amplifiers.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 61291-2:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61280 series NOTE  Harmonized in EN 61280 series.

---------------------- Page: 4 ----------------------

SIST EN 61291-2:2012
- 3 - EN 61291-2:2012

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61291-2:2023(Main)
Optical amplifiers - Part 2: Single channel applications - Performance specification template
SIST EN IEC 61291-2:2023

IEC 61291-2:2023 is available as IEC 61291-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61292-2:2023 provides a performance specification template applicable to optical amplifiers (OAs) used in single channel applications. Multichannel applications are covered in IEC 61291-4. The objective of this template is to provide a framework for the preparation of performance standards and/or product specifications defining the performance of OA devices used in single channel applications. In addition to the requirements specified in this template, a performance standard or product specification could include other parameters, such as ratings, operating conditions, tests, and pass/fail criteria. For a particular application, product specification writers could add specification parameters and/or groups of specification parameters to this template, without removing the parameters specified in this document. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the test methods for gain ripple in Table 2, Table 4 and Table 6 refer now to the IEC 61290‑1 series; - the SOA definition (3.1.3) refers now to IEC 61931.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61290-1:2022(Main)
Optical amplifiers - Test methods - Part 1: Power and gain parameters
SIST EN IEC 61290-1:2022

IEC 61290-1:2022 is available as IEC 61290-1:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1:2022 applies to all commercially available optical amplifiers (OAs) and optically amplified subsystems. It applies to OAs using optically pumped fibres (optical fibre amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect), semiconductors (semiconductor optical amplifiers (SOAs)), and aveguides (planar optical waveguide amplifiers (POWAs)). It is specifically directed to single-channel amplifiers. Test methods for multichannel amplifiers are defined in the IEC 61290-10 series. This document establishes uniform requirements for accurate and reliable measurements of the following OA parameters, as defined in IEC 61291-1:2018, Clause 3: a) nominal output signal power; b) gain; c) reverse gain; d) maximum gain; e) maximum gain wavelength; f) maximum gain variation with temperature; g) gain wavelength band; h) gain wavelength variation; i) gain stability; j) polarization-dependent gain; k) gain ripple (SOA only); l) large-signal output stability; m) saturation output power; n) maximum output signal power; o) maximum total output power. NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is still under study. NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values are acceptable if verified. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - specification of gain ripple as a new parameter; - specification of test method and test report for gain ripple measurements; - use of the term “measurement uncertainty” instead of “measurement accuracy”.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61290-1-3:2021(Main)
Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
SIST EN IEC 61290-1-3:2021

IEC 61290-1-3:2021 is available as IEC 61290-1-3:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-3:2021 applies to all commercially available optical amplifiers (OA) and optically amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-earth doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA). NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is for further study. The object of this document is to establish uniform requirements for accurate and reliable measurements, by means of the optical power meter test method, of the following OA parameters, as defined in IEC 61291-1: - nominal output signal power; - gain; - polarization-dependent gain; - maximum output signal power; - maximum total output power. NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values can be acceptable upon verification. This document applies to single-channel amplifiers. For multichannel amplifiers, IEC 61290-10 (all parts) applies. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - harmonization with IEC 61290-1-1; - use of the term "measurement uncertainty" instead of "measurement accuracy".

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61290-1-1:2020(Main)
Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
SIST EN IEC 61290-1-1:2021

IEC 61290-1-1:2020 is available as IEC 61290-1-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-1:2020 applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optical fibre amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect, semiconductor OAs (SOAs) and planar optical waveguide amplifiers (POWAs). The object of this document is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer (OSA) test method, of the following OA parameters, as defined in IEC 61291-1: - nominal output signal power; - gain; - polarization-dependent gain (PDG); - maximum output signal power; - maximum total output power. In addition, this document provides the test method of: - gain ripple (for SOAs). NOTE All numerical values followed by (‡) are suggested values for which the measurement is assured. The object of this document is specifically directed to single-channel amplifiers. Test methods for multichannel amplifiers are standardized in IEC 61290-10 (all parts). This fourth edition cancels and replaces the third edition published in 2015 and constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: addition of techniques to test gain ripple of SOAs.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61291-5-2:2017/AC:2019-06(Corrigendum)
Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers
SIST EN 61291-5-2:2017/AC:2019
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61290-4-3:2018(Main)
Optical amplifiers - Test methods - Part 4-3: Power transient parameters - Single channel optical amplifiers in output power control
SIST EN IEC 61290-4-3:2018

IEC 61290-4-3:2018 applies to output power controlled optically amplified, elementary sub‑systems. It applies to optical fibre amplifiers (OFAs) using active fibres containing rare‑earth dopants, presently commercially available, as indicated in IEC 61291-1, as well as alternative optical amplifiers that can be used for single channel output power controlled operation, such as semiconductor optical amplifiers (SOAs). The object of this document is to provide the general background for optical amplifiers (OAs) power transients and their measurements and to indicate those IEC standard test methods for accurate and reliable measurements of the following transient parameters: a) transient power response; b) transient power overcompensation response; c) steady-state power offset; d) transient power response time. The stimulus and responses behaviours under consideration include the following: 1. channel power increase (step transient); 2. channel power reduction (inverse step transient); 3. channel power increase/reduction (pulse transient); 4. channel power reduction/increase (inverse pulse transient); 5. channel power increase/reduction/increase (lightning bolt transient); 6. channel power reduction/increase/reduction (inverse lightning bolt transient). These parameters have been included to provide a complete description of the transient behaviour of an output power transient controlled OA. The test definitions defined here are applicable if the amplifier is an OFA or an alternative OA. However, the description in Annex A concentrates on the physical performance of an OFA and provides a detailed description of the behaviour of an OFA; it does not give a similar description of other OA types. Annex B provides a detailed description background of the dynamic phenomenon in output power controlled amplifiers under transient conditions and Annex C details the impact of speed of transient inputs.This second edition cancels and replaces the first edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: alignment of the measure of amplified spontaneous emission (ASE) relative to signal power with the definition in IEC 61290-3-3. Keywords: optical amplifiers (OAs) power transients This International Standard is to be used in conjunction with IEC 61291-1:2012

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61291-1:2018(Main)
Optical amplifiers - Part 1: Generic specification
SIST EN IEC 61291-1:2018

IEC 61291-1:2018 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and waveguides (POWAs). The object of this document is - to establish uniform requirements for transmission, operation, reliability and environmental properties of OAs, and - to provide assistance to the purchaser in the selection of consistently high-quality OA products for his particular applications. Parameters specified for OAs are those characterizing the transmission, operation, reliability and environmental properties of the OA seen as a "black box" from a general point of view. In the sectional and detail specifications a subset of these parameters will be specified according to the type and application of the particular OA device or assembly. This fourth edition cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - terms have been added for parameters from IEC 61290-4-3 and IEC 61290-10-5; - Clause 4 Classification has been removed, since this system is judged to be unused; - the definition of polarization mode dispersion (PMD) has been simplified. Keywords: optical amplifiers (OAs)

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61291-5-2:2017(Main)
Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers
SIST EN 61291-5-2:2017

IEC 61291-5-2:2017(E) applies to optical amplifiers (OAs) and optically amplified, elementary sub-systems for terrestrial applications, using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants, which are commercially available. The black box approach is used in this document. The black box approach is adopted in order to give product specifications which are independent of OA implementation details. For reliability qualification purposes, some information about the internal components is needed; these internal parts are themselves treated as black boxes. This document gives requirements for the evaluation of OA reliability by combining the reliability of such internal black boxes. The object of this document is to specify the minimum list of reliability qualification tests, requirements on failure criteria during testing and on reliability predictions, and give the relevant normative references to establish a standard method for the assessment of the reliability of OFA devices and sub-systems in order to minimize risks and to promote product development and reliability qualification. This second edition cancels and replaces the first edition published in 2002. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) removal of the contents on the relating quality management system from scope, terms and definitions, and the reliability requirements; b) moving fit-rate calculation to Annex B (informative); c) change of requirements for shock test; d) amendment of abbreviations related to changes a) and b).
Keywords: optical amplifiers (OAs), optical fibre amplifiers (OFAs)

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61290-4-1:2016(Main)
Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method
SIST EN 61290-4-1:2017

IEC 61290-4-1:2016 applies to optical amplifiers (OAs) using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants including erbium-doped fibre amplifiers (EDFAs) and optically amplified elementary sub-systems. These amplifiers are commercially available and widely deployed in service provider networks. The object of document is to provide the general background for OFA transients and related parameters, and to describe a standard test method for accurate and reliable measurement of the following transient parameters: - channel addition or removal transient gain overshoot and transient net gain overshoot; - channel addition or removal transient gain undershoot and transient net gain undershoot; - channel addition or removal gain offset; - channel addition or removal transient gain response time constant (settling time). This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - extended the applicability from only EDFAs to all OFAs; - updated definitions for consistency with other documents in the IEC 61290-4 series. Keywords: optical amplifiers (OAs), optical fibre amplifiers (OFAs), rare-earth dopants, erbium-doped fibre amplifiers

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61291-2:2016(Main)
Optical amplifiers - Part 2: Single channel applications - Performance specification template
SIST EN 61291-2:2016

IEC 61291-2:2012 applies to single channel optical amplifier (OA) devices to be used in digital applications. For multichannel applications, use IEC 61291, Part 4. The object of this performance specification template is to provide a frame for the preparation of detail specifications on the performances of single channel OA devices to be used in digital applications. This edition constitutes a minor update through clarification that the scope is for single channel optical amplifiers, and that pump leakage parameters do not apply to semiconductor optical amplifiers.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day