EN IEC 60317-74:2018
(Main)Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180
Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180
IEC 60317-74:2018 specifies the requirements of enamelled rectangular aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor dimensions covered by this standard is: - width: min. 2,0 mm - max. 16,0 mm; - thickness: min. 0,80 mm - max. 5,60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified width/thickness ratio are given in IEC 60317-0-9:2015. Keywords: insulated wires used for windings
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 74: Flachdrähte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 180
Spécifications pour types particuliers de fils de bobinage - Partie 74: Fil de section rectangulaire émaillé en aluminium revêtu de polyesterimide, de classe 180
IEC 60317-74:2018 spécifie les exigences relatives aux fils de bobinage de section rectangulaire en aluminium émaillé de classe 180 à couche de revêtement unique en résine de polyesterimide. Cette couche de revêtement peut être modifiée à condition de conserver les propriétés chimiques de la résine d'origine et de respecter toutes les exigences spécifiées pour les fils. NOTE Une résine modifiée est une résine dont les propriétés chimiques ont été modifiées ou qui contient un ou plusieurs additifs visant à améliorer certaines performances ou caractéristiques d'application. La plage des dimensions nominales des conducteurs couvertes par la présente norme est: - pour la largeur: min. 2,0 mm - max. 16,0 mm; - pour l'épaisseur: min. 0,80 mm - max. 5,60 mm. Les fils de grades 1 et 2 sont couverts par la présente spécification et s'appliquent à toute la gamme des conducteurs. Les combinaisons largeur-épaisseur spécifiées ainsi que le rapport largeur/épaisseur spécifié sont indiqués dans l'IEC 60317-0-9:2015. Mots clés: fils isolés utilisés pour les enroulements
Specifikacije za posebne vrste navijalnih žic - 74. del: Aluminijasta žica s pravokotnim prerezom, emajlirana s poliesterimidom, razred 180 (IEC 60317-74:2018)
Ta del standarda IEC 60317 določa zahteve za emajlirano aluminijasto navijalno žico s pravokotnim prerezom razreda 180 z eno samo prevleko na osnovi poliestramidske smole, ki se lahko spremeni, če ohrani kemijsko identiteto izvirne smole in izpolnjuje vse določene zahteve za žice.
OPOMBA: spremenjena smola je smola, ki je bila kemijsko spremenjena ali vsebuje enega ali več aditivov za izboljšanje določene lastnosti učinkovitosti ali uporabe.
Razpon nazivnih mer prevodnika, ki ga zajema ta standard, je:
– širina: min. 2,0 mm, maks. 16,0 mm;
– debelina: min. 0,80 mm, maks. 5,60 mm.
V to specifikacijo so vključene žice razreda 1 in 2 ter se uporabljajo za celoten nabor prevodnikov.
Navedene kombinacije širine in debeline ter določena razmerja med širino in debelino so podana v standardu IEC 60317-0-9:2015.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60317-74:2018
01-julij-2018
Specifikacije za posebne vrste navijalnih žic - 74. del: Aluminijasta žica s
pravokotnim prerezom, emajlirana s poliesterimidom, razred 180 (IEC 60317-
74:2018)
Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled
rectangular aluminium wire, class 180 (IEC 60317-74:2018)
Ta slovenski standard je istoveten z: EN IEC 60317-74:2018
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
SIST EN IEC 60317-74:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60317-74:2018
---------------------- Page: 2 ----------------------
SIST EN IEC 60317-74:2018
EUROPEAN STANDARD EN IEC 60317-74
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2018
ICS 29.060.10
English Version
Specifications for particular types of winding wires - Part 74:
Polyesterimide enamelled rectangular aluminium wire, class 180
(IEC 60317-74:2018)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 74: Fil de section rectangulaire émaillé en aluminium Wickeldrähten - Teil 74: Flachdrähte aus Aluminium,
revêtu de polyesterimide, de classe 180 lackisoliert mit Polyesterimid, Klasse 180
(IEC 60317-74:2018) (IEC 60317-74:2018)
This European Standard was approved by CENELEC on 2018-04-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-74:2018 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60317-74:2018
EN IEC 60317-74:2018 (E)
European foreword
The text of document 55/1635/FDIS, future edition 1 of IEC 60317-74, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-74:2018.
The following dates are fixed:
• latest date by which the document has to be (dop) 2019-01-03
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-04-03
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-74:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 series NOTE Harmonized as EN 60264 series.
IEC 60317 series NOTE Harmonized as EN 60317 series.
IEC 60851 series NOTE Harmonized as EN 60851 series.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60317-74:2018
EN IEC 60317-74:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.