CLC/TS 50625-3-4:2017

Collection, logistics & treatment requirements for WEEE - Part 3-4: Specification for de-pollution - temperature exchange equipment

This Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard for temperature exchange equipment, EN 50625-2-3, and the Technical Specification for de-pollution, CLC/TS 50625 3-1.

Sammlung, Logistik und Behandlung von Elektro- und Elektronik-Altgeräten (WEEE) – Teil 3-4: Spezifikation der Schadstoffentfrachtung – Wärmeüberträger

Exigences de collecte, logistique et traitement pour les déchets d'équipements électriques et électroniques (DEEE) - Partie 3-4: Spécifications relatives à la dépollution - équipements d'échange thermique

L’article de la Partie 3-1 est remplacé par le suivant: La présente Spécification technique est destinée à être utilisée conjointement avec la norme relative au traitement des DEEE pour les équipements d’échange thermique, EN 50625-2-3, et la Spécification technique relative à la dépollution, CLC/TS 50625 3-1.

Zahteve za zbiranje, logistiko in obdelavo odpadne električne in elektronske opreme (WEEE) - 3-4. del: Specifikacija za preprečevanje onesnaženja - Oprema za toplotno izmenjavo

Ta tehnična specifikacija je namenjena uporabi skupaj s standardom za obdelavo odpadne električne in elektronske opreme (WEEE) za toplotno izmenjavo, s standardom EN 50625-2-3 in s tehnično specifikacijo za preprečevanje onesnaženja, CLC/TS 50625 3-1.

General Information

• Status: Published
• Publication Date: 27-Jul-2017
• ICS: 13.030.99 - Other standards related to wastes
• Technical Committee: CLC/TC 111X - Environment
• Drafting Committee: CLC/TC 111X/WG 06 - WEEE Recycling Standards
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 28-Jul-2017
• Completion Date: 28-Jul-2017
• Directive: 2012/19/EU - Directive 2012/19/EU of the European Parliament and of the Council of 4 July 2012 on waste electrical and electronic equipment (WEEE)
• Mandate: M/518 - Mandate to the European standardisation organisations for standardisation in the field of Waste Electrical and Electronic Equipment (Directive 2012/19/EU (WEEE))
• Ref Project: SIST-TS CLC/TS 50625-3-4:2017 - Collection, logistics & treatment requirements for WEEE - Part 3-4: Specification for de-pollution - temperature exchange equipment

Relations

• Replaces: CLC/TS 50574-2:2014 - Collection, logistics & treatment requirements for end-of-life household appliances containing volatile fluorocarbons or volatile hydrocarbons - Part 2: specification for de-pollution
• Effective Date: 26-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2017
=DKWHYH]D]ELUDQMHORJLVWLNRLQREGHODYRRGSDGQHHOHNWULþQHLQHOHNWURQVNH
RSUHPH:(((GHO6SHFLILNDFLMD]DSUHSUHþHYDQMHRQHVQDåHQMD2SUHPD]D
WRSORWQRL]PHQMDYR
Collection, logistics & treatment requirements for WEEE - Part 3-4: Specification for de-
pollution - temperature exchange equipment
Exigences de collecte, logistique et traitement pour les déchets d'équipements
électriques et électroniques (DEEE) - Partie 3-4: Spécifications relatives à la dépollution -
équipements d'échange thermique
Ta slovenski standard je istoveten z: CLC/TS 50625-3-4:2017
ICS:
13.030.99 Drugi standardi v zvezi z Other standards related to
odpadki wastes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION CLC/TS 50625-3-4

SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
July 2017
ICS 13.030.99
English Version
Collection, logistics & treatment requirements for WEEE - Part 3-
4: Specification for de-pollution - temperature exchange
equipment
Exigences de collecte, logistique et traitement pour les Sammlung, Logistik und Behandlung von Elektro- und
déchets d'équipements électriques et électroniques (DEEE) Elektronik-Altgeräten (WEEE) - Teil 3-4: Spezifikation der
- Partie 3-4: Spécifications relatives à la dépollution - Schadstoffentfrachtung - Wärmeüberträger
équipements d'échange thermique
This Technical Specification was approved by CENELEC on 2017-06-06.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and to make the TS available promptly
at national level in an appropriate form. It is permissible to keep conflicting national standards in force.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. CLC/TS 50625-3-4:2017 E

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 De-pollution monitoring . 6
5 Overview of the applicable methodologies . 16
6 Large appliances . 17
7 Cooling and freezing appliances . 17
8 CRT display / FPD appliances . 17
9 Lamps – Introduction and analysis methodology . 17
10 Small appliances . 17
11 Protocol for components removed during a batch process . 17
12 Sampling and analytical methods . 17
Annex A (normative) Sampling protocol for the physically smallest non-metallic mechanical
treatment fraction . 22
Annex B (normative) Sampling protocol for plastics . 23
Annex C (normative) Targets . 24
Annex D (informative) Target calculation example . 25
Annex AA (normative)  List of countries in the geographical areas . 26
Annex BB (normative)  Compliance evaluation for performance tests . 28
BB.1 Introduction . 28
BB.2 Calculations for step 1 performance test . 28
BB.3 Calculations for step 2 performance test . 29
Annex CC (normative)  Analytical procedures for the determination of residual refrigerant in oil . 31
CC.1 General . 31
CC.2 Method 1 . 31
CC.3 Method 2 . 31
Annex DD (normative)  Analytical procedures for the determination of chemical composition of
refrigerants or blowing agents . 33
DD.1 General . 33
DD.2 Determination of chemical composition of the output refrigerants (VFCs/VHCs) from the
step 1 treatment using mobile analysers . 33
DD.3 Determination of chemical composition of the output refrigerants (VFCs/VHCs) from the

step 1 treatment . 33
DD.4 Determination of chemical composition of the output blowing agents (VFCs/VHCs) from the

step 2 treatment . 33
Annex EE (normative)  Analytical procedures for the polyurethane fraction . 34
EE.1 General . 34
EE.2 Determination of residual VFC and VHC in polyurethane fraction – Method 1 . 34
EE.3 Determination of Residual VFC and VHC in polyurethane Fraction – Method 2 . 35
EE.4 Determination of foreign matters content in polyurethane fraction by thermogravimetric

analysis . 36
EE.5 Determination of foreign matters content in polyurethane fraction by selective extraction

method . 37
Annex FF (normative)  Analytical procedures for visual analysis of residual polyurethane on

metal and plastics fractions . 38
Annex GG (normative)  Analytical procedures for output fractions from step 3 treatment . 39
GG.1 Determination of chemical composition of the collected acids or their neutralization

products from the combustion in step 3 treatment . 39
GG.2 Determination of chemical composition of the alkaline solution from the step 3 treatment . 40
Annex HH (normative)  Determination of VFC and VHC concentration in gas streams . 41
HH.1 General . 41
HH.2 Blowing agent in the raw gas . 41
HH.3 Blowing agent in the clean gas . 41
HH.4 Blowing agent recovered . 42
Annex II (informative)  Structure of the monitoring and reporting system for the step 1, step 2

and step 3 treatment activities . 43
Bibliography . 60

European foreword
This document (CLC/TS 50625-3-4:2017) has been prepared by CLC/TC 111X "Environmental aspects for
electrical and electronic products and systems”.
This document has been prepared under a mandate M/518 given to CENELEC by the European Commission
and the European Free Trade Association.
This Technical Specification part 3-4 is to be used in conjunction with the latest edition of EN 50625-2-3 and
CLC/TS 50625-3-1.
This Technical Specification part 3-4 supplements or modifies the corresponding clauses in
CLC/TS 50625-3-1, so as to convert that publication into the TS: Treatment specification for temperature
exchange equipment.
When a particular subclause of part 3-1 is not mentioned in this part 3-4, that subclause applies as far as is
reasonable. When this standard states "addition", "modification" or "replacement", the relevant text in part 3-1
is to be adapted accordingly.
NOTE The following numbering system is used:
— Sub-clauses, tables and figures that are numbered starting from 101 are additional to those in Part 3-1;
— unless notes are in a new sub-clause or involve notes in Part 3-1, they are numbered starting from 101, including
those in a replaced clause or sub-clause;
— additional annexes are lettered AA, BB, etc.
Introduction
In order to support EN 50625-2-3, Collection, logistics & Treatment requirements for WEEE - Part 2-3:
Treatment requirements for temperature exchange equipment and thereby fulfil the requirement of the
European Commission’s Mandate M/518, it is necessary to include normative requirements, such as target
values and limit values for the analysis, into a document that is able to be revised to take into account both
practical experience and changes in treatment technologies.
1 Scope
This clause of Part 3-1 is replaced with the following:
This Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard for
temperature exchange equipment, EN 50625-2-3, and the Technical Specification for de-pollution,
CLC/TS 50625-3-1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
This clause of Part 3-1 is replaced with the following:
CLC/TS 50625-3-1, Collection, logistics & treatment requirements for WEEE - Part 3-1: Specification for de-
pollution - General
EN 50625-2-3:2017, Collection, logistics & treatment requirements for WEEE - Part 2-3: Treatment
requirements for temperature exchange equipment and other WEEE containing VFC and/or VHC
EN 15002:2015, Characterization of waste - Preparation of test portions from the laboratory sample
ISO/IEC 17025:2005, General requirements for the competence of testing and calibration laboratories
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
This clause of CLC/TS 50625-3-1 and EN 50625-2-3 is applicable with the following addition:
3.108
characteristic number
value of parameter (except target values and limit values) used to determine VFC and VHC removal and
capturing performance for step 1 (e.g. qMtot,, Sk), step 2 (e.g. ,fVFC, fVHC) and step 3 treatment, and value of
parameter used to assess certain results of the plant performance test (e.g. t in step 1 and w and w
max i,VFC i,VHC
in step 2 treatment)
...