EN 60603-13:1998
(Main)Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID)
Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID)
Covers a range of two-part connectors with contact arrangements having spacings of 2,54 mm (0,1 in) in both directions.
Steckverbinder für gedruckte Schaltungen für Frequenzen unter 3 MHz - Teil 13: Bauartspezifikation für gütebestätigte indirekte Steckverbinder für gedruckte Schaltungen mit Raster 2,54 mm (0,1 in), mit freiem Steckverbinder für Schneidklemmenanschluß (ID)
Connecteurs pour fréquences inférieures à 3 MHz pour utilisation avec cartes imprimées - Partie 13: Spécification particulière pour connecteurs en deux parties, sous assurance de la qualité pour cartes imprimées pour grille de base de 2,54mm (0,1 in), avec fiches pour bornes de sortie non-accessibles à déplacement (CAD)
Couvre une gamme de connecteurs enfichables (deux parties), dont la disposition des contacts est telle que ces contacts sont distants de 2,54 mm (0,1 in) dans les deux directions.
Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2002
Connectors for frequencies below 3 MHz for use with printed boards - Part 13:
Detail specification for two-part connectors of assessed quality, for printed boards
for basic grid of 2,54 mm (0,1 in), with free connectors
Connectors for frequencies below 3 MHz for use with printed boards -- Part 13: Detail
specification for two-part connectors of assessed quality, for printed boards for basic grid
of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement
terminations (ID)
Steckverbinder für gedruckte Schaltungen für Frequenzen unter 3 MHz -- Teil 13:
Bauartspezifikation für gütebestätigte indirekte Steckverbinder für gedruckte Schaltungen
mit Raster 2,54 mm (0,1 in), mit freiem Steckverbinder für Schneidklemmenanschluß (ID)
Connecteurs pour fréquences inférieures à 3 MHz pour utilisation avec cartes imprimées
-- Partie 13: Spécification particulière pour connecteurs en deux parties, sous assurance
de la qualité pour cartes imprimées pour grille de base de 2,54mm (0,1 in), avec fiches
pour bornes de sortie non-accessibles à déplacement (CAD)
Ta slovenski standard je istoveten z: EN 60603-13:1998
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEI
NORME
INTERNATIONALE IEC
603-13
INTERNATIONAL
STAN DARD
QC 010000XX0001
Première édition
First edition
1995-01
pour fréquences inférieures à 3 MHz
Connecteurs
imprimées —
pour utilisation avec cartes
13:
Partie
connecteurs en deux
Spécification particulière pour
parties sous assurance de la qualité pour cartes
pour grille de base de 2,54 mm (0,1 in),
imprimées
accessibles
avec fiches pour bornes de sortie non
(CAD)
à déplacement d'isolant
Connectors for frequencies below 3 MHz
—
for use with printed boards
Part 13:
Detail specification for two-part connectors of
assessed quality, for printed boards for basic grid
of 2,54 mm (0,1 in), with free connectors for
non-accessible insulation displacement
terminations (ID)
Droits de reproduction réservés — Copyright - all rights reserved
© CEI 1995
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun pro- any form or by any means, electronic or mechanical,
cédé, électronique ou mécanique, y compris la photocopie et including photocopying and microfilm, without permission
les microfilms, sans l'accord écrit de l'éditeur. in writing from the publisher.
Genève, Suisse
Bureau Central de la Commission Electrotechnique Internationale 3, rue de Varembé
Commission Electrotechnique Internationale CODE PRIX
International Electrotechnical Commission
PRICE PRICE CODECODE
IEC MewayHaposHan 3neMTpoTeXHH4ecna q HOMHCCHN
Pour prix, voir catalogue en vigueur • •
For price, see current catalogue
-3-
603-13 ©IEC:1995
CONTENTS
Page
FOREWORD
Clause
1 Scope 7
2 Normative references 7
11 3 IEC type designation
4 Common features
13 4.1 Isometric view
4.2 Survey of styles
5 Dimensions
5.1 General
5.2 Fixed connectors
5.3 Free connectors 27
5.4 Mounting information for fixed connectors, styles A and B
6 Gauges
7 Characteristics 39
7.1 Climatic category
7.2 Electrical characteristics
7.3 Mechanical characteristics 43
8 Test schedule
47 8.1 General
9 Quality assessment procedures
9.1 Qualification approval testing
9.2 Quality conformance inspection
9.3 Delayed delivery, re-inspection
79 10 Ordering information
Annex A – Test phase BP 3.2: Corrosion, industrial atmosphere
603-13 ©IEC:1995 - 5 -
INTERNATIONAL ELECTROTECHNICAL COMMISSION
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS -
Part 13: Detail specification for two-part connectors of assessed quality,
for printed boards for basic grid of 2,54 mm (0,1 in), with
free connectors for non-accessible insulation
displacement terminations (ID)
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization
comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to
promote international cooperation on all questions concerning standardization in the electrical and
electronic fields. To this end and in addition to other activities, the IEC publishes International Standards.
Their preparation is entrusted to technical committees; any IEC National Committee interested in
the subject dealt with may participate in this preparatory work. International, governmental and
non-governmental organizations liaising with the IEC also participate in this preparation. The IEC
collaborates closely with the International Organization for Standardization (ISO) in accordance with
conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of the IEC on technical matters, prepared by technical committees on
which all the National Committees having a special interest therein are represented, express, as nearly as
possible, an international consensus of opinion on the subjects dealt with.
3) They have the form of recommendations for international use published in the form of standards, technical
reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
International Standard IEC 603-13 has been prepared by sub-committee 48B: Connectors,
of IEC technical committee 48: Electromechanical components and mechanical structures
for electronic equipment.
The text of this standard is based on the following documents:
DIS Report on voting
48B(CO)252 48 B/367/R V D
Full information on the voting for the approval of this standard can be found in the repo rt
on voting indicated in the above table.
The QC number that appears on the front cover of this publication is the specification
number in the IEC Quality Assessment System for Electronic Components (IECQ).
Annex A forms an integral pa rt of this standard.
603-13 © I EC:1995 - 7 -
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS -
Part 13: Detail specification for two-part connectors of assessed quality,
for printed boards for basic grid of 2,54 mm (0,1 in), with
free connectors for non-accessible insulation
displacement terminations (ID)
1 Scope
covers a range of two-part connectors with contact arrangements
This part of IEC 603
having spacings of 2,54 mm (0,1 in) in both directions. The two-part connector range
comprises a fixed (board-mounted) connector containing male contacts and a free connector
containing female contacts. They are primarily intended to provide interconnection
between printed boards using a basic grid of 2,54 mm (0,1 in) as laid down in IEC 97
and round conductor ribbon cable on 1,27 mm (0,05 in) centreline spacing. The fixed
connectors are provided with posts either for solder, press-in or wrapped connections. The
free connectors are provided with non-accessible insulation displacement terminations.
2 Normative references
The following normative documents contain provisions which, through reference in this
text, constitute provisions of this pa rt of IEC 603. At the time of publication, the editions
indicated were valid. All normative documents are subject to revision, and parties to agree-
ments based on this part of IEC 603 are encouraged to investigate the possibility of apply-
ing the most recent editions of the normative documents indicated below. Members of IEC
and ISO maintain registers of currently valid International Standards.
IEC 68-1: 1988, Environmental testing - Part 1: General and guidance
Amendment No. 1 (1992)
Environmental testing - Part 2: Tests - Test Ke: Corrosion tests in
IEC 68-2-60: 1990,
artificial atmosphere at very low concentration of polluting gas(es)
97: 1991, Grid systems for printed circuits
IEC
rt 1: Solderless wrapped connections -
IEC 352-1: 1983, Solderless connections - Pa
General requirements, test methods and practical guidance
Solderless connections - Part 4: Solderless non-accessible insulation
IEC 352-4: 1994,
displacement connections - General requirements, test methods and practical guidance
5: Solderless press-in connections -
IEC 352-5: 1995, Solderless connections - Pa rt
General requirements, test methods and practical guidance
- 9 -
603-13 © I EC:1995
IEC 410: 1973, Sampling plans and procedures for inspection by attributes
Electromechanical components for electronic equipment; basic testing
IEC 512-1: 1984,
rt I: General
procedures and measuring methods - Pa
Amendment No. 1 (1988)
Electromechanical components for electronic equipment; basic testing
IEC 512-2: 1985,
procedures and measuring methods - Part 2: General examination, electrical continuity
and contact resistance tests, insulation tests and voltage stress tests
Electromechanical components for electronic equipment; basic testing
IEC 512-3: 1976,
3: Current-carrying capacity tests
procedures and measuring methods - Pa rt
Electromechanical components for electronic equipment; basic testing
IEC 512-4: 1976,
procedures and measuring methods - Part 4: Dynamic stress tests
Electromechanical components for electronic equipment; basic testing
IEC 512-5: 1992,
procedures and measuring methods - Part 5: Impact tests (free components), static load
tests (fixed components), endurance tests and overload tests
Electromechanical components for electronic equipment; basic testing
IEC 512-7: 1993,
7: Mechanical operating tests and sealing tests
procedures and measuring methods - Pa rt
Electromechanical components for electronic equipment; basic testing
IEC 512-8: 1993,
procedures and measuring methods - Pa rt 8: Connector tests (mechanical) and mech-
anical tests on contacts and terminations
Electromechanical components for electronic equipment; basic testing
IEC 512-9: 1992,
rt 9: Miscellaneous tests
procedures and measuring methods - Pa
Connectors for frequencies below 3 MHz for use with printed boards -
IEC 603-1: 1991,
Part is Generic specification - General requirements and guide for the preparation of
detail specifications, with assessed quality
Amendment No. 1 (1992)
Rules of procedure of the IEC quality assessment system for
IEC QC 001002: 1986,
electronic components (IECQ)
Amendment No. 1 (1992)
Fastener hexagon products - Width across flats
ISO 272: 1982,
Surface roughness - Parameters, their values and general rules for
ISO 468: 1982,
specifying requirements
- 11 -
603-13 ©IEC:1995
3 IEC type designation
Connectors, fixed (board-mounted) and free, with and without strain reliefs and latches
according to this standard shall be designated by the following system.
IEC 603-13 N L N L L
^
Letter denoting
Reference to this
assessment level
specification
B Assessment level B
G Assessment level G
Letter See 5.2.1 A
denoting See 5.2.2 B
the style See 5.3.1 C
Number denoting
performance level PL
1 Performance level PL1
2 Performance level PL2
010 3 Performance level PL3
rformance level PL4
4 Pe
Letter denoting strain relief
and latches
Number of contacts 026
Fixed connector without latches
A
030 (in combination with free connector
without and with strain relief)
Fixed connector with short
B (10,8 mm) latches (in combination
with free connector without strain relief)
Fixed connector with long
C (14,4 mm) latches (in combination with
free connector with strain relief)
Free connector without strain relief
D (in combination with fixed connector
rt latches)
without strain relief or with sho
Male M
Letter denoting Two-part
Free connector with strain relief
style of contact connector
Female F
E (in combination with fixed connector
without latches or with long latches)
Insulation displacement connectors D –
Press-in P –
Solder S – Number denoting contact finish
Wrapped connections W
1 Gold, gold alloy
Not applicable – 0
2 Silver, silver alloy
– 1
Fixed connector, board up to 1,6 mm,
3 Tin, ti n alloy
90° solder termination
Fixed connector, board up to 3,2 mm, _ 2
Letter denoting
90° solder termination
basic style and Letter denoting state of assembling
Fixed connector, mother board up to
number denoting
– 3
_
1.6 mm, straight solder termination
c Complete connector
application of
Fixed connector, mother board up to _
termination
3,2 mm, straight solder termination _
Fixed connector, straight termination – 5
for wrapped connections
_ 6
Fixed connector, 90° for termination
for wrapped connections
_ 7
Free connector, termination for
insulation displacement —
NOTE – "L" stands for letter
Fixed connector, board up to 2,4 mm, _ 8
"N" stands for number
straight press-in termination
Example - Connector style B, having 20 male contacts gold-finished with solder terminations.
Complete fixed connector for boards up to 3,2 mm (0,126 in), straight termination without
latches, with performance level 2 and assessment level G: IEC 603-13-B020MS-4C1A-2G.
- 13 -
603-13 © I EC:1995
4 Common features
Not applicable.
4.1 Isometric view
Strain relief
Printed board
IEC 519194
Figure 1 - Isometric view
603-13 © IEC:1995 - 15 -
4.2 Survey of styles
Table 1 - Survey of styles
Number of contacts
Style
16/20/24/26/30/34/36
4/6/8 10/12/14
40/44/50/52/56/60/64
A Fixed connector;
press-i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.