EN 61918:2013
(Main)Industrial communication networks - Installation of communication networks in industrial premises
Industrial communication networks - Installation of communication networks in industrial premises
IEC 61918:2013 specifies basic requirements for the installation of media for communication networks in industrial premises and within and between the automation islands, of industrial sites. This standard covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media, but not the wireless media itself. Additional media are covered in the IEC 61784-5 series. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. It includes the following changes: - some terms and abbreviated terms have been added to Clause 3; - Subclauses 4.4.3.4.1 and 4.4.7.3 have been updated; - Subclause 8.1 has been updated; - Figure 13, Figure 29, Figure H.1, Table 3, Table 6, Table 7 and Table B.5 have been updated; - Annex D and Annex M have been extended to cover additional communication profile families; - A new informative Annex O has been added.
Industrielle Kommunikationsnetze – Installation von Kommunikationsnetzen in Industrieanlagen
Réseaux de communication industriels - Installation de réseaux de communication dans des locaux industriels
La CEI 61918:2013 spécifie les exigences de base pour l'installation d'un support de réseaux de communication dans des locaux industriels et à l'intérieur et entre des îlots d'automatisation de sites industriels. La présente norme couvre le câblage symétrique et à fibres optiques. Elle couvre également l'infrastructure de câblage des supports sans fil, mais pas le support sans fil lui-même. D'autres supports sont couverts par la série CEI 61784-5. Cette troisième édition annule et remplace la deuxième édition parue en 2010 et constitue une révision technique. Elle inclut les modifications suivantes: - certains termes et abréviations ont été ajoutés à l'Article 3; - les Paragraphes 4.4.3.4.1 et 4.4.7.3 ont été mis à jour; - le Paragraphe 8.1 a été mis à jour; - la Figure 13, la Figure 29, la Figure H.1, le Tableau 3, le Tableau 6, le Tableau 7 et le Tableau B.5 ont été mis à jour; - Annexe D et l'Annexe M ont été étendues pour couvrir des familles de profil de communication supplémentaires; - une nouvelle Annexe O informative a été ajoutée.
Industrijska komunikacijska omrežja - Inštalacija komunikacijskih omrežij v industrijskih okoljih (IEC 61918:2013 spremenjen)
Ta mednarodni standard opredeljuje osnovne zahteve za inštalacijo medijev za komunikacijska omrežja v industrijskih okoljih ter znotraj avtomatiziranih otokov industrijskih lokacij in med njimi. Ta standard vključuje uravnoteženo kablovje iz optičnih vlaken. Prva tako vključuje kabelsko infrastrukturo za brezžične medije, vendar ne samih brezžičnih medijev. Dodatne medije obravnava skupina standardov IEC 61784-5. Ta standard je spremljevalni standard h komunikacijskim omrežjem industrijskih avtomatiziranih otokov in posebej h komunikacijskim omrežjem, opredeljenim v skupinah standardov IEC 61158 in IEC 61784. Poleg tega ta standard obravnava: • inštalacijo generičnega telekomunikacijskega kablovja za industrijska okolja, kot je določeno v ISO/IEC 24702; • povezavo med generičnim telekomunikacijskim kablovjem, določenim v ISO/IEC 24702, in posebnim komunikacijskim kablovjem avtomatiziranega otoka, kjer avtomatiziran izhod (AO) nadomešča telekomunikacijski izhod (TO) iz ISO/IEC 24702. Ta standard nudi smernice za urejanje kritičnih vidikov industrijskih avtomatiziranih področij (varnost in okoljske vidike, kot so motnje zaradi mehanskih vplivov, tekočine, delcev, podnebja, kemikalij in elektromagnetizma). Ta standard ne priznava postopkov distribucije energije prek uravnoteženih kabelskih sistemov Ethernet, ki niso opredeljeni v IEEE 802.3 in v IEEE 802.3at. Ta standard obravnava vloge načrtovalca, monterja, preverjevalca, osebja za opravljanje prevzemnih preskusov, administrativnega osebja in osebja za vzdrževanje ter opredeljuje ustrezne odgovornosti in/ali podaja vodilo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Industrijska komunikacijska omrežja - Inštalacija komunikacijskih omrežij v industrijskih okoljih (IEC 61918:2013 spremenjen)Industrielle Kommunikationsnetze - Installation von Kommunikationsnetzen in Industrieanlagen (IEC 61918:2013, modifiziert)Réseaux de communication industriels - Installation des réseaux de communication dans les locaux industriels (CEI 61918:2013, modifiée)Industrial communication networks - Installation of communication networks in industrial premises (IEC 61918:2013, modified)35.110OmreževanjeNetworking25.040.40Merjenje in krmiljenje industrijskih postopkovIndustrial process measurement and controlICS:Ta slovenski standard je istoveten z:EN 61918:2013SIST EN 61918:2014en01-junij-2014SIST EN 61918:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD EN 61918 NORME EUROPÉENNE
EUROPÄISCHE NORM December 2013
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61918:2013 E
ICS 25.040.40; 33.020; 35.240.50 Supersedes EN 61918:2008
English version
Industrial communication networks -
Installation of communication networks in industrial premises (IEC 61918:2013, modified)
Réseaux de communication industriels -
Installation de réseaux de communication dans des locaux industriels (CEI 61918:2013, modifiée)
Industrielle Kommunikationsnetze – Installation von Kommunikationsnetzen in Industrieanlagen (IEC 61918:2013, modifiziert)
This European Standard was approved by CENELEC on 2013-10-02. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Foreword
The text of document 65C/737/FDIS, future edition 3 of IEC 61918, prepared by SC 65C, "Industrial networks", of IEC/TC 65, "Industrial-process measurement, control and automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61918:2013. A draft amendment, which covers common modifications to IEC 61918:2013, was prepared by CLC/TC 65X "Industrial-process measurement, control and automation" and approved by CENELEC.
The following dates are fixed:
• latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-10-02 • latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2016-10-02
This document supersedes EN 61918:2008.
– some terms and abbreviated terms have been added to Clause 3; – Subclauses 4.4.3.4.1, 4.4.7.2.1, and 4.4.7.3 have been updated; – Subclause 5.7.4.3 has been updated as result of the revision of the installation profiles;
– Subclause 6.2.3.1 has been updated;
– Subclause 8.1 has been updated; – Figure 2, Figure 13, Figure 15, Figure 29, Figure H.1, Table 3, Table 6, Table 7, Table 14, Table B.3 and
Table B.5 have been updated; – a new Figure 35 has been added; – a new Table 10 has been added;
– Annex D and Annex M have been extended to cover additional communication profile families; – Annex F has been extended to cover conductor sizes in electrical cables;
– Annex H has been made normative; some common requirements are extended as result of the revision of the installation profiles; – a new informative Annex O has been added. This standard is to be used in conjunction with the EN 61784-5 series with regard to the installation of communication profiles (CPs). This standard is to be used in conjunction with ISO/IEC 14763-2 with regard to the installation of generic cabling in accordance with EN 50173-3. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
– 3 – EN 61918:2013 Endorsement notice
The text of the International Standard IEC 61918:2013 was approved by CENELEC as a European Standard with agreed common modifications.
COMMON MODIFICATIONS
• Introduction Replace the last paragraph before Figure 2 by: For the installation of generic cabling this standard is to be used in conjunction with EN 50174 (see Figure 2). • Figure 2 – Standards relationships Replace the original figure by the following one, which shows the standards relationships at European level:
INDUSTRIAL PREMISESEN 50173-3OFFICE PREMISESHOMES DATA CENTRESEN 50173-2EN 50173-4EN 50173-5EN 50174-1GENERIC CABLINGBETWEENAUTOMATIONISLANDSAPPLICATION-SPECIFICCABLINGWITHINAUTOMATIONISLANDSBETWEENAUTOMATIONISLANDSDESIGNData centre clauseHomeclauseOfficesclauseIndustrialclauseEN 50174-2EN 50174-3PLANNING AND INSTALLATIONEN
61918(Common requirements)EN 61158 seriesandEN 61784-1, -2EN 61784-5seriesInstallation profiles(Selection +Add/Repl/Mod)Common structureINDUSTRIAL PREMISESEN 50173-3OFFICE PREMISESHOMES DATA CENTRESEN 50173-2EN 50173-4EN 50173-5EN 50174-1GENERIC CABLINGBETWEENAUTOMATIONISLANDSAPPLICATION-SPECIFICCABLINGWITHINAUTOMATIONISLANDSBETWEENAUTOMATIONISLANDSDESIGNData centre clauseHomeclauseOfficesclauseIndustrialclauseEN 50174-2EN 50174-3PLANNING AND INSTALLATIONEN
61918(Common requirements)EN 61158 seriesandEN 61784-1, -2EN 61784-5seriesInstallation profiles(Selection +Add/Repl/Mod)Common structure Figure 2 - Network installation: Standards relationships at European level
• 2 Normative references In EN 61918 the normative references shall be modified as follows: EN 50288 replaces IEC 61156 and HD 60364 replaces IEC 60364.
• In IEC 61918 the generic cabling is intended as ‘in accordance with ISO/IEC 24702’.
In EN 61918 the generic cabling shall be intended as ‘in accordance with EN 50173-3’. • In the Bibliography, add the following notes for the standards indicated: IEC 60060-1 NOTE
Harmonized as EN 60060-1. IEC 60079-11:2011 NOTE
Harmonized as EN 60079-11:2012 (not modified). IEC 60079-14 NOTE
Harmonized as EN 60079-14. IEC 60228 NOTE
Harmonized as EN 60228. IEC 60332-1 series NOTE
Harmonized in EN 60332-1 series. IEC 60364 series NOTE
Harmonized in EN/HD 60364 series. IEC 60512-4 series NOTE
Harmonized in EN 60512-4 series. IEC 60664-1 NOTE
Harmonized as EN 60664-1. IEC 60670-1:2002 NOTE
Harmonized as EN 60670-1:2005 (modified). IEC 60950-21 NOTE
Harmonized as EN 60950-21. IEC 61000-4-4 NOTE
Harmonized as EN 61000-4-4. IEC 61000-6-2 NOTE
Harmonized as EN 61000-6-2. IEC 61000-6-4 NOTE
Harmonized as EN 61000-6-4. IEC 61010-1 NOTE
Harmonized as EN 61010-1. IEC 61131-2:2007 NOTE
Harmonized as EN 61131-2:2007 (not modified). IEC 61508-4 NOTE
Harmonized as EN 61508-4. IEC 61984:2008 NOTE
Harmonized as EN 61984:2009 (not modified).
– 5 – EN 61918:2013 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
- - Multi-element metallic cables used in analogue and digital communication and control
EN 50288 Series
- - Application of equipotential bonding and earthing in buildings with information technology equipment EN 50310 -
IEC 60364-1 (mod) + corr. August
2005 2009 Low-voltage electrical installations -
Part 1: Fundamental principles, assessment of general characteristics, definitions HD 60364-1 2008
IEC 60364-4-41 - Low-voltage electrical installations -
Part 4-41: Protection for safety - Protection against electric shock HD 60364-4-41
-
IEC 60364-4-44 - Low-voltage electrical installations -
Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances HD 60364-4-442 -
IEC 60364-5-54 - Low-voltage electrical installations -
Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors HD 60364-5-54 -
IEC 60529 - Degrees of protection provided by enclosures (IP Code) EN 60529 -
IEC 60603 Series Connectors for frequencies below 3 MHz for use with printed boards
EN 60603 Series
IEC 60603-7 Series Connectors for electronic equipment -
Part 7: Detail specification for 8-way, shielded, free and fixed connectors EN 60603-7 Series
IEC 60757 - Code for designation of colours HD 457 S1 -
IEC 60793 Series Optical fibres EN 60793 Series
IEC 60793-2-10 - Optical fibres -
Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres EN 60793-2-10 -
IEC 60794 Series Optical fibre cables
EN 60794 Series
IEC 60807-2 - Rectangular connectors for frequencies below 3 MHz -
Part 2: Detail specification for a range of connectors, with assesed quality, with trapezoidal shaped metal shells and round contacts - Fixed solder contact types - -
Publication Year Title EN/HD Year IEC 60807-3 - Rectangular connectors for frequencies below 3 MHz -
Part 3: Detail specification for a range of connectors with trapezoidal shaped metal shells and round contacts - Removable crimp types with closed crimp barrels, rear insertion/rear extraction - -
IEC 60825-2 - Safety of laser products -
Part 2: Safety of optical fibre communication systems (OFCS) EN 60825-2 -
IEC 60950-1
- Information technology equipment - Safety -
Part 1: General requirements EN 60950-1 -
IEC 61076-2-101 - Connectors for electronic equipment - Product requirements -
Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking EN 61076-2-101 -
IEC/PAS 61076-2-109 - Connectors for electronic equipment - Product requirements -
Part 2-109: Circular connectors - Detail specification for connectors M12 x 1 with screw-locking, for data transmissions with frequencies up to 500 MHz - -
IEC 61076-3-106 - Connectors for electronic equipment - Product requirements -
Part 3-106: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface EN 61076-3-106 -
IEC 61076-3-117 - Connectors for electronic equipment - Product requirements -
Part 3-117: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface - Variant 14 related to IEC 61076-3-106 - Push pull coupling EN 61076-3-117 -
IEC 61158 Series Industrial communication networks -
Fieldbus specifications
EN 61158 Series
IEC 61158-2 201X1) Industrial communication networks -
Fieldbus specifications -
Part 2: Physical layer specification and service definition EN 61158-2 201X1)
IEC 61169-8 - Radio-frequency connectors -
Part 8: Sectional specification - RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock - Characteristics impedance 50 ohms (type BNC) EN 61169-8 -
IEC 61753 Series Fibre optic interconnecting devices and passive components performance standard
EN 61753 Series
1) To be published. SIST EN 61918:2014
– 7 – EN 61918:2013 Publication Year Title EN/HD Year IEC 61754-2 - Fibre optic connector interfaces -
Part 2: Type BFOC/2,5 connector family EN 61754-2 -
IEC 61754-4 - Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces -
Part 4: Type SC connector family EN 61754-4 -
IEC 61754-20 - Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces -
Part 20: Type LC connector family EN 61754-20 -
IEC 61754-22 - Fibre optic connector interfaces -
Part 22: Type F-SMA connector family EN 61754-22 -
IEC 61754-24 - Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces -
Part 24: Type SC-RJ connector family EN 61754-24 -
IEC 61784 Series Industrial communication networks - Profiles
EN 61784 Series
IEC 61784-1 - Industrial communication networks - Profiles -
Part 1: Fieldbus profiles EN 61784-1 -
IEC 61784-2 201X1) Industrial communication networks - Profiles -
Part 2: Additional fieldbus profiles for real-time networks based on ISO/IEC 8802-3 EN 61784-2 201X1)
IEC 61784-3 - Industrial communication networks - Profiles -
Part 3: Functional safety fieldbuses - General rules and profile definitions EN 61784-3 -
IEC 61784-5 Series Industrial communication networks - Profiles -
Part 5-2: Installation of fieldbuses - Installation profiles for CPF 2 EN 61784-5 Series
IEC 61935-1 (mod) + corr. October
2009 2010 Specification for the testing of balanced and coaxial information technology cabling -
Part 1: Installed balanced cabling as specified in ISO/IEC 11801 and related standards EN 61935-1 2009
IEC 61935-2 - Specification for the testing of balanced and coaxial information technology cabling -
Part 2: Cords as specified in ISO/IEC 11801 and related standards EN 61935-2 -
IEC 62026-3 - Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) -
Part 3: DeviceNet EN 62026-3 -
IEC 62439 Series Industrial communication networks - High availability automation networks
EN 62439 Series
IEC 62443 Series Industrial communication networks - Network and system security
- -
ISO/IEC 8802-3 - Information technology - Telecommunications and information exchange between systems - Loca
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.