EN 62841-2-1:2018/A1:2022
(Amendment)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact drills
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact drills
2022-04-01- HD: NEXT ACTION: TB ACTION (2nd FV draft sent to production on 2022-03-25)
2020-06-16: Common mods to this prA1 are included in prAC (PR=72183)
DOW=DOR+48 months
Elektrische Motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-1: Besondere Anforderungen für handgeführte Bohrmaschinen und Schlagbohrmaschinen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-1: Exigences particulières pour les perceuses portatives et les perceuses à percussion
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-1. del: Posebne zahteve za ročne vrtalnike in udarne (vibracijske) vrtalnike - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2022
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-
1. del: Posebne zahteve za ročne vrtalnike in udarne (vibracijske) vrtalnike -
Dopolnilo A1
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact
drills
Ta slovenski standard je istoveten z: EN 62841-2-1:2018/A1:2022
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 62841-2-1:2018/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2022
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-1: Particular
requirements for hand-held drills and impact drills
(IEC 62841-2-1:2017/AMD1:2021)
Outils électroportatifs à moteur, outils portables et machines Elektrische Motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-1: Exigences transportable Werkzeuge und Rasen- und
particulières pour les perceuses portatives et les perceuses Gartenmaschinen - Sicherheit - Teil 2-1: Besondere
à percussion Anforderungen für handgeführte Bohrmaschinen und
(IEC 62841-2-1:2017/AMD1:2021) Schlagbohrmaschinen
(IEC 62841-2-1:2017/AMD1:2021)
This amendment A1 modifies the European Standard EN 62841-2-1:2018; it was approved by CENELEC on 2021-12-09. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-2-1:2018/A1:2022 E
European foreword
The text of document 116/519/FDIS, future IEC 62841-2-1/AMD1, prepared by IEC/TC 116 "Safety of
motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-2-1:2018/A1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-06-27
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-06-27
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential
requirements of EU Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an
integral part of EN 62841-2-1:2018/A12:2022.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62841-2-1:2017/AMD1:2021 was approved by CENELEC
as a European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 62841-2-2 NOTE Harmonized as EN 62841-2-2
IEC 62841-2-6 NOTE Harmonized as EN IEC 62841-2-6
IEC 62841-2-1 ®
Edition 1.0 2021-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery –
Part 2-1: Particular requirements for hand-held drills and impact drills
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses –
Partie 2-1: Exigences particulières pour les perceuses portatives et les
perceuses à percussion
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-5394-6
– 2 – IEC 62841-2-1:2017/AMD1:2021
© IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
Part 2-1: Particular requirements for hand-held drills and impact drills
AMENDMENT 1
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to IEC 62841-2-1:2017 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this Amendment is based on the following documents:
Draft Report on voting
116/519/FDIS 116/525/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Amendment is English.
IEC 62841-2-1:2017/AMD1:2021 – 3 –
© IEC 2021
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
available at www.iec.ch/members_experts/refdocs. The main document types developed by
IEC are described in greater detail at www.iec.ch/standardsdev/publications/.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
1 Scope
Replace the existing text with the following new text:
This clause of Part 1 is applicable except as follows:
Addition:
This part of IEC 62841 applies to hand-held drills and impact drills, including diamond core
drills. This document also applies to drills that can be used for driving screws by attaching
screwdriver bits.
This document does not apply to rotary hammers, screwdrivers, impact wrenches and ratchet
drivers even if they can be used as a drill.
NOTE 101 Rotary hammers are covered by IEC 62841-2-6.
NOTE 102 Screwdrivers, impact wrenches and ratchet drivers are covered by IEC 62841-2-2.
8 Marking and instructions
Delete existing Subclause 8.3.
18 Abnormal operation
Replace the existing text of 18.8 with the following new text:
– 4 – IEC 62841-2-1:2017/AMD1:2021
© IEC 2021
18.8 Replacement of Table 4:
Table 4 – Required performance levels
Type and purpose of SCF Minimum performance level
(PL)
Power switch – prevent unwanted switch-on for tools with M ≤ 25 Nm a
R
measured in accordance with 19.102
Power switch – prevent unwanted switch-on for tools with M > 25 Nm b
R
measured in accordance with 19.102
Power switch – provide desired switch-off for tools with M ≤ 25 Nm b
R
measured in accordance with 19.102
Power switch – provide desired switch-off for tools with M > 25 Nm c
R
measured in accordance with 19.102
Power switch – provide desired switch-off for tools that require bracing in Shall be evaluated using the
accordance with 8.14.1.101. fault conditions of 18.6.1 without
the loss of this SCF
Provide desired direction of rotation for tools that do not require bracing in Not an SCF
accordance with 8.14.1.101
Provide desired direction of rotation for tools that require bracing in c
accordance with 8.14.1.101
Any electronic control to pass the test of 18.3 a
-1
For tools with a rated no-load speed of less than 3 500 min , prevent a
output speed from exceeding 150 % of rated no-load speed as measured in
19.6
-1
For tools with a rated no-load speed of 3 500 min or greater, prevent a
output speed from exceeding 130 % of rated no-load speed as measured in
19.6
Prevent exceeding thermal limits as in 18.4 a
Prevent self-resetting as required in 23.3 for tools with M ≤ 25 Nm a
R
measured in accordance with 19.102
Prevent self-resetting as required in 23.3 for tools with M > 25 Nm b
R
measured in accordance with 19.102
Limit the torque to comply with 19.102 c
Prevent unwanted lock-on of the power switch function for tools with b
M ≤ 25 Nm measured in accordance with 19.102
R
Prevent unwanted lock-on of the power switch function for tools with c
M > 25 Nm measured in accordance with 19.102
R
19 Mechanical hazards
Add the following new subclause:
19.6 Replacement:
The no-load speed of the spindle at rated voltage shall not exceed 120 % of the rated no-
load speed.
Compliance is checked by measuring the speed of the spindle after the tool has been
operating for 5 min at no-load. During the test, separable accessories are not mounted.
IEC 62841-2-1:2017/AMD1:2021 – 5 –
© IEC 2021
19.102.1 General
Replace the existing text of the last paragraph with the following new text:
Compliance is checked by the tests specified in 19.102.2 to 19.102.4 and by the calculations
in Figures 104 to 107.
19.102.2 Test equipment
Replace the existing text of the first paragraph, item a) and item b) with the following new
text:
The test equipment used for the test of 19.102.4 shall meet the following requirements a) to
g):
a) The torque transducer and the rotational angle sensor shall continuously monitor the
torque and the rotation produced by the output spindle of the tool during the test of
19.102.4.
b) The output of the torque transducer shall be connected to an oscilloscope or other data
acquisition equipmen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.