iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50065-4-3:2023

(Main)

Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter

Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter

This document applies to incoming filters used to control the coupling of signals between the utility area and the consumer area, as illustrated in Figure 1. This document defines: - the minimum impedance in the relevant frequency band(s) at both utility port and consumer port, - the minimum attenuation of unwanted signals transmitted from the utility side to the consumer side and vice versa. This document applies to incoming filters designed for single or multiphase installations. [Figure 1 - The application of incoming filter]

Signalübertragung auf elektrischen Niederspannungsnetzen im Frequenzbereich 3 kHz bis 148,5 kHz - Teil 4-3: Niederspannungs-Entkopplungsfilter - Eingangsfilter

Transmission de signaux sur les réseaux électriques basse tension dans la bande de fréquences de 3 kHz à 148,5 kHz - Partie 4-3: Filtre de découplage basse tension - Filtre de branchement

Le présent document s'applique aux filtres de branchement utilisés pour contrôler le couplage des signaux entre la zone distributeur d'énergie et la zone consommateur, comme cela est représenté à la Figure 1. Le présent document définit: - l'impédance minimale dans la ou les bandes de fréquences pertinentes pour l'accès distributeur d'énergie et pour l'accès consommateur, - l'affaiblissement minimal des signaux indésirables transmis par l'accès distributeur d'énergie vers l'accès consommateur et vice-versa. [Figure 1 - Application d'un filtre de branchement]

Signalizacija po nizkonapetostnih električnih napeljavah v frekvenčnem območju od 3 kHz do 148,5 kHz - 4-3. del: Nizkonapetostni ločilni filtri - Vhodni filter

Standard se uporablja za vhodne filtre, ki se jih uporablja za krmiljenje povezovanja signalov med območjem omrežnega napajanja in območjem porabnikov. Standard opredeljuje: minimalno impedanco v ustreznih frekvenčnih pasovih tako na omrežnih napajalnih vratih kot na vratih porabnika, minimalno atenuacijo neželenih signalov, ki se prenašajo iz omrežne napajalne strani do porabnika in obratno. Standard se uporablja za vhodne filtre, ki so zasnovani za eno- ali večfazne inštalacije.

General Information

Status
Published
Publication Date
23-Mar-2023
ICS
31.160 - Electric filters
33.040.30 - Switching and signalling systems
97.120 - Automatic controls for household use
Technical Committee
CLC/TC 205A - Mains communicating systems
Drafting Committee
CLC/TC 205A/WG 12 - Filters
Current Stage
6060 - Document made available - Publishing
Start Date
24-Mar-2023
Due Date
10-Sep-2022
Completion Date
24-Mar-2023
Directive
2004/22/EC - Directive 2004/22/EC of the European Parliament and of the Council of 31 March 2004 on measuring instruments
Mandate
M/441 - Standardisation mandate to CEN, CENELEC and ETSI in the field of measuring instruments for the development of an open architecture for utility meters involving communication protocols enabling interoperability
M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
Ref Project
SIST EN 50065-4-3:2023 - Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter

Relations

Replaces
EN 50065-4-3:2003 - Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter
Effective Date
14-May-2019

Buy Standard

EN 50065-4-3:2023EN 50065-4-3:2023
PreviousNext
Standard
EN 50065-4-3:2023
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50065-4-3:2023
01-maj-2023
Signalizacija po nizkonapetostnih električnih napeljavah v frekvenčnem območju
od 3 kHz do 148,5 kHz - 4-3. del: Nizkonapetostni ločilni filtri - Vhodni filter
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5
kHz - Part 4-3: Low voltage decoupling filter - Incoming filter
Signalübertragung auf elektrischen Niederspannungsnetzen im Frenquenzbereich 3 kHz
bis 148,5 kHz - Teil 4-3: Niederspannungs-Entkopplungsfilter - Eingangsfilter
Transmission de signaux sur les réseaux électriques basse tension dans la bande de
fréquences de 3 kHz à 148,5 kHz - Partie 4-3: Filtres de découplage basse tension -
Filtre de branchement
Ta slovenski standard je istoveten z: EN 50065-4-3:2023
ICS:
31.160 Električni filtri Electric filters
33.040.30 Komutacijski in signalizacijski Switching and signalling
sistem systems
SIST EN 50065-4-3:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50065-4-3:2023

---------------------- Page: 2 ----------------------
SIST EN 50065-4-3:2023
EUROPEAN STANDARD EN 50065-4-3
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2023
ICS 31.160; 33.040.30; 97.120 Supersedes EN 50065-4-3:2003
English Version
Signalling on low-voltage electrical installations in the frequency
range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling
filter - Incoming filter
Transmission de signaux sur les réseaux électriques basse Signalübertragung auf elektrischen Niederspannungsnetzen
tension dans la bande de fréquences de 3 kHz à 148,5 kHz im Frenquenzbereich 3 kHz bis 148,5 kHz - Teil 4-3:
- Partie 4-3: Filtre de découplage basse tension - Filtre de Niederspannungs-Entkopplungsfilter - Eingangsfilter
branchement
This European Standard was approved by CENELEC on 2022-10-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50065-4-3:2023 E

---------------------- Page: 3 ----------------------
SIST EN 50065-4-3:2023
EN 50065-4-3:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Classification . 5
4.1 General . 5
4.2 Type 1 . 5
4.3 Type 2 . 5
4.4 Type 3 . 5
5 Incoming filter electrical characteristics .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50065-4-5:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-5: Low voltage decoupling filter - Segmentation filter
SIST EN 50065-4-5:2023

This document applies to segmentation filters in a mains communication system intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. These filters are used to control the coupling of signals between two areas of a mains communication system, as illustrated in Figure 1. This document defines in the relevant frequency range: - the minimum impedance at both ports of the filter, - the minimum attenuation of signals transmitted between the ports of the filter. [Figure 1 - Application of segmentation filters]

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-6:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-6: Low voltage decoupling filters - Phase coupler
SIST EN 50065-4-6:2023

This document applies to phase couplers in a mains communication system intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. Phase couplers are used to control the coupling of communication signals between phases or sections of a mains communication system. This document defines - the requirements to ensure a minimum coupling between the phases or sections of a mains communication system, and - the requirements to ensure no change on the safety of the electrical installation.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-4:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-4: Low voltage decoupling filter - Impedance filter
SIST EN 50065-4-4:2023

This document applies to impedance filters in a mains communication system, intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. These filters are used to set a suitable impedance, in the nominal frequency range of the mains signalling system, at any point of the low voltage mains network where a low impedance equipment is connected, as shown in Figure 1, in order to allow reliable operation of the mains signalling system. Impedance filters can be used either in utility or consumer networks. They can also be used in conjunction with incoming filters and segmentation filters. [Figure 1 - The application of impedance filters]

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-1:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-1: Low voltage decoupling filters - Generic specification
SIST EN 50065-4-1:2023

This document applies to decoupling filters installed on the low voltage mains network and operating in the frequency range 3 kHz to 148,5 kHz. It does not apply to EMI suppression filters incorporated in household equipment or other general electric equipment. It specifies the definitions, requirements and test methods of the functional, technical and environmental characteristics of the decoupling filter, e.g. impedance, transfer function, voltage drop, leakage current and power dissipation. The impedance and the transfer function are referred to the decoupling filter mains power ports (see Figure 1).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-7:2005(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz - Part 4-7: Portable low voltage decoupling filters - Safety requirements
SIST EN 50065-4-7:2006

This European product safety standard applies to the filter part of portable devices for household and similar uses (hereafter referred to as portable decoupling filters) consisting of the filter part, a plug or an appliance inlet or a provision for connection by terminals or with a non-rewirable cord and one (multiple) socket-outlet or an appliance outlet. They are intended for single-phase circuits for nominal currents not exceeding 16 A and for nominal voltages not exceeding 250 V a.c. to neutral operating in the frequency range 3 kHz to 148,5 kHz and from 1,6 MHz to 30 MHz. The filtering functions are described in EN 50065-4-1. This standard does not cover phase couplers. Portable decoupling filters shall not be used as part of the fixed installation, where EN 50065-4-2 applies. Plugs and socket-outlets connected to the filter part and plugs and socket-outlets integrated with the filter part shall comply with the relevant national standard(s). Appliance inlets and appliance outlets connected to the filter part shall comply with the relevant parts of the EN 60320 series. Appliance inlets and appliance outlets integrated with the filter parts are not covered by this standard. This standard can be used for portable mains communication devices when no other product standard exists. This standard can be used for other portable mains filters other than those described in EN 50065-4-1 when no other product standard exists. Filters including batteries are not covered by this standard.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-6:2004(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-6: Low voltage decoupling filters - Phase coupler
SIST EN 50065-4-6:2005

This European Standard applies to phase couplers in a mains communication system for phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings. This European Standard applies to phase couplers used to control the coupling of communication signals between phases or sections of a mains communication system. A “phase coupler” may be used to achieve coupling between the phases of a multiphase installation, or to provide bridging of signals around other system components. The standard defines  the requirements to ensure a minimum coupling between the sections, and  the requirements to ensure no change on the safety of the electrical installation.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-5:2003(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-5: Low voltage decoupling filter - Segmentation filter
SIST EN 50065-4-5:2004

This standard applies to segmentation filters in a mains communication system used for single or multiphase installations having a phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings and utility networks. These filters (see Figure 1) are used to control the coupling of signals between two areas of a mains communication system. The standard defines -the minimum impedance in the relevant frequency range(s) at both ports, -the minimum attenuation of signals transmitted between port.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-4:2003(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-4: Low voltage decoupling filter - Impedance filter
SIST EN 50065-4-4:2004

This standard applies to impedance filters in a mains communication system for phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings. This standard also applies to "plug-in filters". These filters (see Figure 1) are used to set a suitable impedance, in the nominal frequency range of the mains signalling system, at any point of the low voltage mains network where a low impedance equipment is connected, in order to allow reliable operation of mains signalling system. These impedance filters can be used either in utility or consumer networks. They may also be used in conjunction with incoming filters and segmentation filters.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
FprEN 50065-4-2(Main)
Signalling on low voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-2: Low voltage decoupling filters - Safety requirements
oSIST prEN 50065-4-2:2021

This product safety standard applies to decoupling filters in a mains communication system intended for utility networks or household and similar fixed-electrical installations including residential, commercial and light industrial buildings.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
FprEN 50065-4-7(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-7: Portable low voltage decoupling filters - Safety requirements
oSIST prEN 50065-4-7:2021

This product safety standard applies to the filter part of portable devices for household and similar uses consisting of the filter part, a plug or an appliance inlet or a provision for connection by terminals or with a non-rewirable cord and a socket-outlet or an appliance outlet. They are intended for single-phase circuits for nominal currents not exceeding 16 A and for nominal voltages not exceeding 250 V a.c.. This standard does not cover phase couplers. Filters including batteries are not covered by this standard.

  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day