Hand-held motor-operated electric tools - Safety - Part 2-14: Particular requirements for planers

Deals with the safety of tools which the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools and 440 V for three-phase a.c. tools. Supplements or modifies the corresponding clauses of IEC 60745-1

Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-14: Besondere Anforderungen für Hobel

Outils électroportatifs à moteur - Sécurité - Partie 2-14: Règles particulières pour les rabots

Električna ročna orodja - Varnost - 2-14. del: Posebne zahteve za skobeljnike (IEC 60745-2-14:2003 + A1:2006, spremenjen)

General Information

Status
Withdrawn
Publication Date
29-Sep-2009
Current Stage
6060 - Document made available - Publishing
Start Date
30-Sep-2009
Due Date
30-Oct-2009
Completion Date
30-Sep-2009

Relations

Buy Standard

Standard
EN 60745-2-14:2009
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60745-2-14:2009
01-december-2009
1DGRPHãþD
SIST EN 60745-2-14:2004
(OHNWULþQDURþQDRURGMD9DUQRVWGHO3RVHEQH]DKWHYH]DVNREHOMQLNH ,(&
$VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety -- Part 2-14: Particular requirements for
planers
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-14: Besondere
Anforderungen für Hobel
Outils électroportatifs à moteur - Sécurité -- Partie 2-14: Règles particulières pour les
rabots
Ta slovenski standard je istoveten z: EN 60745-2-14:2009
ICS:
25.140.20 (OHNWULþQDRURGMD Electric tools
79.120.20 Lesnoobdelovalno orodje Woodworking tools
SIST EN 60745-2-14:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60745-2-14:2009

---------------------- Page: 2 ----------------------

SIST EN 60745-2-14:2009

EUROPEAN STANDARD
EN 60745-2-14

NORME EUROPÉENNE
September 2009
EUROPÄISCHE NORM

ICS 25.140.20 Supersedes EN 60745-2-14:2003 + A1:2007 + A11:2007


English version


Hand-held motor-operated electric tools -
Safety -
Part 2-14: Particular requirements for planers
(IEC 60745-2-14:2003 + A1:2006, modified)


Outils électroportatifs à moteur -  Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-14: Règles particulières Sicherheit -
pour les rabots Teil 2-14: Besondere Anforderungen
(CEI 60745-2-14:2003 + A1:2006, für Hobel
modifiés) (IEC 60745-2-14:2003 + A1:2006,
modifiziert)




This European Standard was approved by CENELEC on 2009-07-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-14:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60745-2-14:2009
EN 60745-2-14:2009 - 2 -
Foreword
The text of the International Standard IEC 60745-2-14:2003 prepared by SC 61F (transformed into
IEC TC 116, Safety of hand-held motor-operated electric tools), together with the common
modifications prepared by the Technical Committee CENELEC TC 61F (transformed into TC 116)
was submitted to the formal vote and was approved by CENELEC as EN 60745-2-14 on 2003-07-01.
A draft amendment (prAA) was prepared to align Subclause 6.2 with the new Subclause 6.2 in
EN 60745-1. Moreover, vibration values determined with the new 6.2 are complying with the
requirements of the Physical Agents Directive Vibration 2002/44/EC. The text of the draft was
submitted to the Unique Acceptance Procedure and was approved by CENELEC as amendment A11
to EN 60745-2-14:2003 on 2007-06-01.
The text of amendment 1:2006 to the International Standard IEC 60745-2-14:2003, together with
common modifications prepared by the Technical Committee CENELEC TC 116, was submitted to the
Unique Acceptance Procedure and was approved by CENELEC as amendment A1 to
EN 60745-2-14:2003 on 2007-02-01.
A further draft amendment (prAC), extending Annex ZZ to include the new MD 2006/42/EC, was
submitted to the formal vote.
The combined texts were approved by CENELEC as a new edition of EN 60745-2-14 on 2009-07-01.
This European Standard supersedes EN 60745-2-14:2003 + A11:2007 + A1:2007.
The following dates were fixed:
- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-02-01
- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-02-01
This standard is divided into two parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools (for
the purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2: Requirements for particular types of tools which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and supports the essential requirements of
EC Directive 98/37/EC (Machinery Directive), amended by EC Directive 98/79/EC, and of EC Directive
2006/42/EC. See Annexes ZZA and ZZB.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EC Directives can be applicable to the products falling
within the scope of this standard.
This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.
This Part 2-14 is to be used in conjunction with EN 60745-1:2009. When this standard states
"addition", "modification" or "replacement", the relevant text of Part 1 is to be adapted accordingly.

---------------------- Page: 4 ----------------------

SIST EN 60745-2-14:2009
- 3 - EN 60745-2-14:2009

Subclauses and figures which are additional to those in Part 1 are numbered starting from 101.
Subclauses, tables and figures which are additional to those in IEC 60745-2-14 are prefixed “Z”.
NOTE In this standard, the following print types are used:
- Requirements: in roman type;
- Test specification: in italic type;
- Notes: in smaller roman type.

---------------------- Page: 5 ----------------------

SIST EN 60745-2-14:2009
EN 60745-2-14:2009 - 4 -
Endorsement notice
The text of the International Standard IEC 60745-2-14:2003 + A1:2006 was approved by CENELEC
as a European Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable except as follows:
6.1.2.4 Modification:
Planers are suspended in such a way as to correspond to normal use. The base plate shall be
horizontal.
6.1.2.5 Modification:
Planers are tested at no-load.
6.2 Vibration
6.2.4.2 Location of the measurement
Addition:
Figure Z101 shows the positions on the main handle and guide handle, if applicable.
6.2.6.3 Operating conditions
Planers are tested under load observing the conditions shown in Table Z101.

---------------------- Page: 6 ----------------------

SIST EN 60745-2-14:2009
- 5 - EN 60745-2-14:2009

Table Z101 – Test conditions
Orientation Planing along a horizontal surface of a softwood workpiece.
The workpiece shall have the dimensions of 400 mm x B x 90 mm
where B is the maximum planing width of the tool less 15 mm.
The workpiece shall be firmly secured to the test rig using resilient
material, which shall be mounted so that it does not have any
significant resonance in the frequency range that can influence the test
result
Tool bit Blade as specified for planing softwood. The cutting depth shall be set
to maximum capacity
Feed force As necessary for smoothly working without overloading the machine.
Equal forces are applied to both handles avoiding excessive gripping
forces
Test cycle Planing the complete length of 400 mm at maximum depth of cut.
The measurement starts when the blade enters the wood and finishes
when the blade leaves the wood
NOTE Examples of softwood are pine and fir.
6.2.7.2 Declaration of the vibration total value
Addition:
The vibration total value a of the handle with the highest emission and the uncertainty K shall be
h
declared.
8 Marking and instructions
Add:
8.12.2 a) Addition:
Z101) Information on the correct use of the dust collection system
Z102) Advice to wear a dust mask
19 Mechanical hazards
Add the following new subclause:
19.Z101 The cutting head shall be round shaped except for the part of the blades, the gullet width
and clamping screws.
The maximum gullet width s in mm shall be
s = 0,235 d + 7,2
max
where d is the cutting diameter. See Figure 101.
Compliance is checked by inspection and by measurement.

---------------------- Page: 7 ----------------------

SIST EN 60745-2-14:2009
EN 60745-2-14:2009 - 6 -
21 Construction
Add:
21.Z1 Addition:
Planers are considered to be tools where a considerable amount of dust is produced.

---------------------- Page: 8 ----------------------

SIST EN 60745-2-14:2009
- 7 - EN 60745-2-14:2009

Replace Figure 101 by:

Key
1 Fixed shoe
2 Adjustable shoe

Figure 101 – Examples of cutting heads with basic dimensions and clearance distances

---------------------- Page: 9 ----------------------

SIST EN 60745-2-14:2009
EN 60745-2-14:2009 - 8 -
Add the following new figure:


Figure Z101 - Position of transducers

---------------------- Page: 10 ----------------------

SIST EN 60745-2-14:2009
- 9 - EN 60745-2-14:2009

Add the following annex:
Annex ZZ
(informative)

Coverage of Essential Requirements of EC Directives
Annex ZZA
(informative)

Coverage of Essential Requirements of Directive 98/37/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 98/37/EC (Machinery Directive), amended
by Directive 98/79/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.
Annex ZZB
(informative)

Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.
__________

---------------------- Page: 11 ----------------------

SIST EN 60745-2-14:2009

---------------------- Page: 12 ----------------------

SIST EN 60745-2-14:2009
NORME CEI
INTERNATIONALE
IEC



60745-2-14
INTERNATIONAL


Edition 2.1
STANDARD


2006-05


Edition 2:2003 consolidée par l'amendement 1:2006
Edition 2:2003 consolidated with amendment 1:2006
Outils électroportatifs à moteur –
Sécurité –
Partie 2-14:
Règles particulières pour les rabots

Hand-held motor-operated electric tools –
Safety –
Part 2-14:
Particular requirements for planers

 IEC 2006 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
CC
Commission Electrotechnique Internationale
PRICE CODE
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 13 ----------------------

SIST EN 60745-2-14:2009
60745-2-14 © IEC:2003+A1:2006 – 3 –
CONTENTS
FOREWORD.5
1 Scope.9
2 Normative references.9
3 Definitions.9
4 General requirements .9
5 General conditions for the tests .9
6 Void.9
7 Classification.11
8 Marking and instructions.11
9 Protection against access to live parts.11
10 Starting.11
11 Input and current .11
12 Heating.11
13 Leakage current.13
14 Moisture resistance.13
15 Electric strength.13
16 Overload protection of transformers and associated circuits .13
17 Endurance.13
18 Abnormal operation.13
19 Mechanical hazards.13
20 Mechanical strength .25
21 Construction.25
22 Internal wiring.25
23 Components.25
24 Supply connection and external flexible cords .25
25 Terminals for external conductors.25
26 Provision for earthing .25
27 Screws and connections .25
28 Creepage distances, clearances and distances through insulation.27
29 Resistance to heat, fire and tracking.27
30 Resistance to rusting.27
31 Radiation, toxicity and similar hazards.27

Annexes .29
Annex K (normative) Battery tools and battery packs .29
Annex L (normative) Battery tools and battery packs provided
with mains connection or non-isolated sources .29
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.