EN 61347-2-6:2001
(Main)Lamp controlgear - Part 2-6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting
Lamp controlgear - Part 2-6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting
This part of EN 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges such as in aircraft. This first edition of EN 61347-2-6, together with EN 61347-1, cancels and replaces section five of the first edition of EN 60924, published in 1990, and constitutes a minor revision. This standard shall be used in conjunction with EN 61347-1. It was established on the basis of the first edition (2000) of that standard.
Geräte für Lampen - Teil 2-6: Besondere Anforderungen an gleichstromversorgte elektronische Vorschaltgeräte für die Beleuchtung von Luftfahrzeugen
Appareillages de lampes - Partie 2-6: Prescriptions particulières pour les ballasts électroniques alimentés en courant continu pour l'éclairage des aéronefs
La présente partie de la EN 61347 spécifie les prescriptions particulières de sécurité pour les ballasts électroniques alimentés en courant continu destinés à fonctionner sur des sources de tension exposées à des phénomènes transitoires et à des surtensions, telles que celles des avions. Cette première édition de la EN 61347-2-6, conjointement avec la EN 61347-1, annule et remplace la section cinq de la première édition de la EN 60924, parue en 1990, dont elle constitue une révision mineure. Cette norme doit être utilisée conjointement avec la EN 61347-1. Elle a été établie sur la base de la première édition (2000) de cette norme.
Lamp controlgear – Part 2-6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting (IEC 61347-2-6:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2002
1DGRPHãþD
SIST EN 60924:1995
Lamp controlgear – Part 2-6: Particular requirements for d.c. supplied electronic
ballasts for aircraft lighting (IEC 61347-2-6:2000)
Lamp controlgear -- Part 2-6: Particular requirements for d.c. supplied electronic ballasts
for aircraft lighting
Geräte für Lampen -- Teil 2-6: Besondere Anforderungen an gleichstromversorgte
elektronische Vorschaltgeräte für die Beleuchtung von Luftfahrzeugen
Appareillages de lampes -- Partie 2-6: Prescriptions particulières pour les ballasts
électroniques alimentés en courant continu pour l'éclairage des aéronefs
Ta slovenski standard je istoveten z: EN 61347-2-6:2001
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
NORME CEI
INTERNATIONALE
IEC
61347-2-6
INTERNATIONAL
Première édition
STANDARD
First edition
2000-10
Appareillages de lampes –
Partie 2-6:
Prescriptions particulières pour les ballasts
électroniques alimentés en courant continu
pour l'éclairage des aéronefs
Lamp controlgear –
Part 2-6:
Particular requirements for d.c. supplied
electronic ballasts for aircraft lighting
© IEC 2000 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun procédé, any form or by any means, electronic or mechanical,
électronique ou mécanique, y compris la photocopie et les including photocopying and microfilm, without permission in
microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE N
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue
61347-2-6 © IEC:2000 – 3 –
CONTENTS
Page
FOREWORD . 5
INTRODUCTION .9
Clause
1 Scope . 11
2 Normative references . 11
3 Definitions. 11
4 General requirements. 11
5 General notes on tests . 11
6 Classification .11
7 Marking. 13
7.1 Mandatory marking. 13
7.2 Information to be provided, if applicable . 13
8 Protection against accidental contact with live parts. 13
9 Terminals. 13
10 Provisions for earthing. 13
11 Moisture resistance and insulation. 13
12 Electric strength .13
13 Thermal endurance test for windings . 13
14 Pulse voltages.15
15 Abnormal conditions. 17
16 Fault conditions.19
17 Construction. 19
18 Creepage distances and clearances . 19
19 Screws, current-carrying parts and connections . 19
20 Resistance to heat, fire and tracking. 19
21 Resistance to corrosion. 19
Annexes . 25
Figure 1 – Suitable circuit for producing and applying short-duration pulses. 21
Figure 2 – Circuit for testing rectifying effect . 23
Table 1 – Long duration pulse voltages . 15
Table 2 – Short-duration pulse voltages (10 µs or less) . 15
61347-2-6 © IEC:2000 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
––––––––––––
LAMP CONTROLGEAR –
Part 2-6: Particular requirements for d.c. supplied electronic
ballasts for aircraft lighting
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61347-2-6 has been prepared by subcommittee 34C: Auxiliaires for
lamps, of IEC technical committee 34: Lamps and related equipment.
This first edition of IEC 61347-2-6, together with IEC 61347-1, cancels and replaces section
five of the first edition of IEC 60924, published in 1990, and constitutes a minor revision.
This standard shall be used in conjunction with IEC 61347-1. It was established on the basis of
the first edition (2000) of that standard.
This part 2 supplements or modifies the corresponding clauses in IEC 61347-1 so as to convert
that publication into the IEC standard: Particular requirements for d.c. supplied electronic
ballasts for aircraft lighting.
NOTE In this standard, the following print types are used:
– Requirements proper: in roman type.
– Test specifications: in italic type.
– Explanatory matter: in smaller roman type.
61347-2-6 © IEC:2000 – 7 –
The text of this standard is based on the following documents:
FDIS Report on voting
34C/503/FDIS 34C/517/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
Annexes A to H form an integral part of this standard.
IEC 61347 consists of the following parts, under the general title: Lamp controlgear:
– Part 1: General and safety requirements
)
– Part 2-1: Particular requirements for starting devices (other than glow starters
– Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors
for filament lamps
– Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps
– Part 2-4: Particular requirements for d.c. electronic ballasts for general lighting
– Part 2-5: Particular requirements for d.c. supplied electronic ballasts for public transport
lighting
– Part 2-6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting
– Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting
– Part 2-8: Particular requirements for ballasts for fluorescent lamps
– Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent
lamps)
– Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency
operation of cold start tubular discharge lamps (neon tubes)
– Part 2-11: Particular requirements for miscellaneous electronic circuits used with
1)
luminaires
The committee has decided that the contents of this publication will remain unchanged
until 2003. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
–––––––––––
1)
To be published.
61347-2-6 © IEC:2000 – 9 –
INTRODUCTION
This first edition of IEC 61347-2-6, published in conjunction with IEC 61347-1, represents an
editorial review of section five of IEC 60924. The formatting into separately published parts
provides for ease of future amendments and revisions. Additional requirements will be added
as and when a need for them is recognized.
This standard, and the parts which make up IEC 61347-2, in referring to any of the clauses of
IEC 61347-1, specify the extent to which such a clause is applicable and the order in which the
tests are to be performed; they also include additional requirements, as necessary. All parts
which make up IEC 61347-2 are self-contained and, therefore, do not include references to
each other.
Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standard
by the phrase "The requirements of clause n of IEC 61347-1 apply", this phrase is interpreted
as meaning that all requirements of the clause in question of part 1 apply, except any which are
clearly inapplicable to the specific type of lamp controlgear covered by this particular part of
IEC 61347-2.
61347-2-6 © IEC:2000 – 11 –
LAMP CONTROLGEAR –
Part 2-6: Particular requirements for d.c. supplied electronic
ballasts for aircraft lighting
1 Scope
This part of IEC 61347 specifies particular safety requirements for d.c. supplied electronic
ballasts intended for operation from power sources likely to have attendant transients and
surges such as in aircraft.
Performance requirements are the subject of IEC 60925.
2 Normative references
For the purpose of this part of IEC 61347, the normative references given in clause 2 of
IEC 61347-1 which are mentioned in this standard apply, together with the following normative
references.
IEC 61347-1, Lamp controlgear – Part 1: General and safety requirements
IEC 60925, D.C. supplied electronic ballasts for tubular fluorescent lamps – Performance
requirements
3 Definitions
For the purpose of this part of IEC 61347, the definitions of clause 3 of IEC 61347-1 apply.
4 General requirements
The requirements of clause 4 of IEC 61347-1 apply.
5 General notes on tests
The requirements of clause 5 of IEC 61347-1 apply.
6 Classification
The requirements of clause 6 of IEC 61347-1 are not applicable.
61347-2-6 © IEC:2000 – 13 –
7 Marking
7.1 Mandatory marking
Ballasts shall be clearly and durably marked, in accordance with the requirements of 7.2 of
IEC 61347-1, with the following mandatory markings:
– items a), b), e), f), k) and l) of 7.1 of IEC 61347-1, together with
– indication of type and current rating of the fuse, if applicable.
7.2 Information to be provided, if applicable
In addition to the above mandatory markings, the following information, if applicable, shall be
given either on the ballast, or be made available
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.