EN IEC 60317-80:2019
(Main)Specifications for particular types of winding wires - Part 80: Polyvinyl acetal enamelled rectangular copper wire, class 120, with a bonding layer
Specifications for particular types of winding wires - Part 80: Polyvinyl acetal enamelled rectangular copper wire, class 120, with a bonding layer
IEC 60317-80: 2019 specifies the requirements of enamelled rectangular copper winding wire of class 120 with a dual coating. The underlying coating is based on polyvinyl acetal resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The second coating is a bonding layer based on a thermoplastic or thermosetting resin. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor dimensions covered by this document is: width: min. 2,00 mm max. 16,00 mm; thickness: min. 0,80 mm max. 5,60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of nominal width and thickness as well as the specified ratio width/thickness are given in IEC 60317-0-2:2019. Keywords: insulated wires used for windings
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 80: Flachdrähte aus Kupfer, lackisoliert mit Polyvinylacetal, mit einer Backlackschicht, Klasse 120
Spécifications pour types particuliers de fils de bobinage - Partie 80: Fil de section rectangulaire en cuivre émaillé avec acétal de polyvinyle, classe 120, avec une couche adhérente
IEC 60317-80:2019 spécifie les exigences relatives aux fils de bobinage de section rectangulaire en cuivre émaillé de classe 120 avec un double revêtement. La sous-couche est à base de résine acétal de polyvinyle, qui peut être modifiée sous réserve de conserver l'identité chimique de la résine initiale et de répondre à toutes les exigences spécifiées pour le fil. La deuxième couche est une couche adhérente à base de résine thermoplastique ou thermodurcissable. NOTE Une résine modifiée est une résine qui a subi une modification chimique, ou qui contient un ou plusieurs additifs pour améliorer les résultats obtenus ou les caractéristiques d'utilisation. La gamme des dimensions nominales des conducteurs couverte par le présent document est: largeur: min. 2,00 mm max. 16,00 mm; épaisseur: min. 0,80 mm max. 5,60 mm. Les fils de grade 1 et de grade 2 sont compris dans la présente spécification et s'appliquent à la gamme complète des conducteurs. Les combinaisons spécifiées de largeur et d'épaisseur nominales ainsi que le rapport largeur/épaisseur spécifié sont indiqués dans l'IEC 60317-0-2:2019. Mots clés : fils isolés utilisés pour les enroulements
Specifikacije za posebne vrste navijalnih žic - 80. del: S polivinil acetalom emajliran bakren vodnik s pravokotnim prerezom, razred 120, s spajalno plastjo (IEC 60317-80:2019)
Ta dokument določa zahteve za emajlirano bakreno navijalno žico s pravokotnim prerezom razreda 120 z dvojno prevleko. Spodnja prevleka je osnovana na polivinil acetalni smoli, ki jo je mogoče prilagoditi, če ohrani kemijsko identiteto izvirne smole in zadosti vsem določenim zahtevam žice. Druga prevleka je vezana plast, ki je osnovana na plastomerni ali termoreaktivni smoli. Razpon nazivnih mer prevodnika, ki ga zajema ta dokument, je: – širina: najmanj 2,00 mm, največ 16,00 mm; – debelina: najmanj 0,80 mm, največ 5,60 mm. V to specifikacijo so vključene žice razreda 1 in 2, ki se uporabljajo za celoten nabor prevodnikov. Navedene kombinacije nazivne širine in debeline ter določena razmerja med širino in debelino so podana v standardu IEC 60317-0-2:2019.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2019
Specifikacije za posebne vrste navijalnih žic - 80. del: S polivinil acetalom
emajliran bakren vodnik s pravokotnim prerezom, razred 120, s spajalno plastjo
(IEC 60317-80:2019)
Specifications for particular types of winding wires - Part 80: Polyvinyl acetal enamelled
rectangular copper wire, class 120, with a bonding layer (IEC 60317-80:2019)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 80:
Flachdrähte aus Kupfer, lackisoliert mit Polyvinylacetal, mit einer Backlackschicht,
Klasse 120 (IEC 60317-80:2019)
Spécifications pour types particuliers de fils de bobinage - Partie 80: Fil de section
rectangulaire en cuivre émaillé avec acétal de polyvinyle, classe 120, avec une couche
adhérente (IEC 60317-80:2019)
Ta slovenski standard je istoveten z: EN IEC 60317-80:2019
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60317-80
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2019
ICS 29.060.10
English Version
Specifications for particular types of winding wires - Part 80:
Polyvinyl acetal enamelled rectangular copper wire, class 120,
with a bonding layer
(IEC 60317-80:2019)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 80: Fil de section rectangulaire en cuivre émaillé Wickeldrähten - Teil 80: Flachdrähte aus Kupfer, lackisoliert
avec acétal de polyvinyle, classe 120, avec une couche mit Polyvinylacetal, mit einer Backlackschicht, Klasse 120
adhérente (IEC 60317-80:2019)
(IEC 60317-80:2019)
This European Standard was approved by CENELEC on 2019-09-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-80:2019 E
European foreword
The text of document 55/1790/FDIS, future edition 1 of IEC 60317-80, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-25
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-80:2019 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)
ISO 6892-1:2016 NOTE Harmonized as EN ISO 6892-1:2016 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
1 2
IEC 60317-0-2 20XX Specifications for particular types of winding EN IEC 60317-0-2 20XX
wires - Part 0-2: General requirements -
Enamelled rectangular copper wire
IEC 60851-4 2016 Winding wires - Test methods - Part 4: EN 60851-4 2016
Chemical properties
Under preparation. Stage at the time of publication: IEC CDV 60317-0-2:2019.
Under preparation. Stage at the time of publication: prEN IEC 60317-0-2:2019.
IEC 60317-80 ®
Edition 1.0 2019-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 80: Polyvinyl acetal enamelled rectangular copper wire, class 120,
with a bonding layer
Spécifications pour types particuliers de fils de bobinage –
Partie 80: Fil de section rectangulaire en cuivre émaillé avec acétal
de polyvinyle, classe 120, avec une couche adhérente
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-7309-8
– 2 – IEC 60317-80:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
4.1 Conductor dimensions . 7
4.2 Enamel layer . 7
4.3 Bonding layer . 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 8
8.1 Mandrel winding test . 8
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 9
17 Solderability . 9
18 Heat or solvent bonding . 9
18.1 Heat bonding . 9
18.1.1 Room temperature . 9
18.1.2 Elevated temperature . 9
18.2 Solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Mandrel winding . 8
IEC 60317-80:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 80: Polyvinyl acetal enamelled rectangular copper wire,
class 120, with a bonding layer
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the ma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.