EN 62037-5:2013
(Main)Passive RF and microwave devices, intermodulation level measurement - Part 5: Measurement of passive intermodulation in filters
Passive RF and microwave devices, intermodulation level measurement - Part 5: Measurement of passive intermodulation in filters
IEC 62037-5:2013(E) defines test fixtures and procedures recommended for measuring levels of passive intermodulation generated by filters, typically used in wireless communication systems. The purpose is to define qualification and acceptance test methods for filters for use in low intermodulation (low IM) applications.
Passive HF- und Mikrowellenbauteile, Messung des Intermodulationspegels - Teil 5: Messung der passiven Intermodulation in Filtern
Dispositifs RF et à micro-ondes passifs, mesure du niveau d’intermodulation - Partie 5: Mesure de l’intermodulation passive dans les filtres
La CEI 62037-5:2013 définit les dispositifs et les procédures d'essai recommandés pour mesurer les niveaux d'intermodulation passive générés par les filtres, généralement utilisés dans les systèmes de communication sans fil. L'objectif est de définir des méthodes d'essai de qualification et d'acceptation pour les filtres destinés à être utilisés dans des applications d'intermodulation basse (IM basse).
Pasivne radiofrekvenčne (rf) in mikrovalovne naprave, meritve intermodulacijskega nivoja - 5. del: Meritve pasivne intermodulacije v filtrih (IEC 62037-5:2013)
Ta del standarda IEC 62037 določa preskusne vpenjalne naprave in postopke, ki so priporočljivi za merjenje ravni pasivne intermodulacije, ki jo proizvedejo filtri, običajno uporabljeni v brezžičnih komunikacijskih sistemih. Namen je določiti kvalifikacijske in sprejemljivostne preskusne metode za filtre za uporabo pri nizki intermodulaciji (nizka IM).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2014
1DGRPHãþD
SIST EN 62037:2001
3DVLYQHUDGLRIUHNYHQþQH UI LQPLNURYDORYQHQDSUDYHPHULWYH
LQWHUPRGXODFLMVNHJDQLYRMDGHO 0HULWYHSDVLYQHLQWHUPRGXODFLMHYILOWULK ,(&
Passive r.f. and microwave devices, intermodulation level measurement - Part 5:
Measurement of passive intermodulation in filters
Passive HF- und Mikrowellenbauteile, Messung des Intermodulationspegels - Teil 5:
Messung der passiven Intermodulation in Filtern
Dispositifs RF et à micro-ondes passifs, mesure du niveau d’intermodulation - Partie 5:
Mesure de l’intermodulation passive dans les filtres
Ta slovenski standard je istoveten z: EN 62037-5:2013
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 62037-5
NORME EUROPÉENNE
April 2013
EUROPÄISCHE NORM
ICS 33.040.20 Supersedes EN 62037:1999 (partially)
English version
Passive RF and microwave devices, intermodulation level measurement -
Part 5: Measurement of passive intermodulation in filters
(IEC 62037-5:2013)
Dispositifs RF et à micro-ondes passifs, Passive HF- und Mikrowellenbauteile,
mesure du niveau d’intermodulation - Messung des Intermodulationspegels -
Partie 5: Mesure de l’intermodulation Teil 5: Messung der passiven
passive dans les filtres Intermodulation in Filtern
(CEI 62037-5:2013) (IEC 62037-5:2013)
This European Standard was approved by CENELEC on 2013-02-20. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62037-5:2013 E
Foreword
The text of document 46/409/FDIS, future edition 1 of IEC 62037-5, prepared by IEC TC 46 "Cables,
wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62037-5:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2013-11-20
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-02-20
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document partially supersedes EN 62037:1999.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62037-5:2013 was approved by CENELEC as a European
Standard without any modification.
- 3 - EN 62037-5:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 62037-1 2012 Passive RF and microwave devices, EN 62037-1 2012
intermodulation level measurement -
Part 1: General requirements and measuring
methods
IEC 62037-5 ®
Edition 1.0 2013-01
INTERNATIONAL
STANDARD
Passive RF and microwave devices, intermodulation level measurement –
Part 5: Measurement of passive intermodulation in filters
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 33.040.20 ISBN 978-2-83220-580-8
– 2 – 62037-5 © IEC:2013(E)
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Abbreviations . 5
4 General comments on PIM testing of filter assemblies . 5
4.1 Sources of error: back-to-back filters . 5
4.2 Environmental and dynamic PIM testing . 6
4.3 General test procedure . 7
5 Example test equipment schematics for filter testing . 7
5.1 General . 7
5.2 Transmit band testing . 7
5.3 Receive band testing: dual high-power carriers . 8
5.4 Receive band testing: injected interferer . 10
Figure 1 – Typical receive band PIM test set-up . 6
Figure 2 – Typical test equipment schematic for measuring transmit-band, forward,
passive IM products on an N-port DUT using two high-power carriers . 8
Figure 3 – Typical test equipment schematic for measuring receive-band, forward,
passive IM products on an N-port DUT, using two high-power carriers . 9
Figure 4 – Typical test equipment schematic for measuring receive-band, reverse,
passive IM products on an N-port DUT, using two high-power carriers . 9
Figure 5 – Typical test equipment schematic for measuring receive-band, passive IM
products on an N-port DUT, using two high-power carriers . 10
Figure 6 – Typical test equipment schematic for measuring receive-band, forward,
passive IM products on an N-port DUT, using the injected interferer technique . 11
Figure 7 – Typical test equipment schematic for measuring receive-band, reverse,
passive IM products on an N-port DUT, using the injected interferer technique . 11
Figure 8 – Typical test equipment schematic for measuring receive-band, passive IM
products on an N-port DUT, using the injected interferer technique . 12
Table 1 – Summary table referencing example test equipment schematics for
measuring PIM on filter-type devices . 7
62037-5 © IEC:2013(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PASSIVE RF AND MICROWAVE DEVICES,
INTERMODULATION LEVEL MEASUREMENT –
Part 5: Measurement of passive intermodulation in filters
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62037-5 has been prepared by technical committee 46: Cables,
wires, waveguides, r.f. connectors, r.f. and microwave passive components and accessories.
The text of this standard is based on the following documents:
FDIS Report on voting
46/409/FDIS 46/421/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 62037-5 © IEC:2013(E)
A list of all the parts in the IEC 62037 series, published under the general title Passive RF
and microwave devices, Intermodulation level measurement can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
62037-5 © IEC:2013(E) – 5 –
PASSIVE RF AND MICROWAVE DEVICES,
INTERMODULATION LEVEL MEASUREMENT –
Part 5: Measurement of passive intermodulation in filters
1 Scope
This part of IEC 62037 defines test fixtures and procedures recommended for measuring
levels of passive intermodulation generated by filters, typically used in wireless
communication systems. The purpose is to define qualification and acceptance test methods
for filters for use in low intermodulation (low IM) applications.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest editi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.