EN 61003-1:2004
(Main)Industrial-process control systems - Instruments with analogue inputs and two- or multi-state outputs - Part 1: Methods of evaluating performance
Industrial-process control systems - Instruments with analogue inputs and two- or multi-state outputs - Part 1: Methods of evaluating performance
is applicable to pneumatic and electric industrial-process instruments using measured values that are continuous signals in accordance with EN 60382, or EN 60381-1. The other input value (i.e. the set point value) may be either a mechanical (position, force, etc.) or a standard signal.
Systeme der industriellen Prozessleittechnik - Geräte mit analogen Eingängen und Zwei- oder Mehrpunktverhalten - Teil 1: Verfahren zur Bewertung des Betriebsverhaltens
Processus industriels - Instruments avec entrées analogiques et sorties à deux ou plusieurs états - Partie 1: Méthodes d'évaluation des performances
is applicable to pneumatic and electric industrial-process instruments using measured values that are continuous signals in accordance with EN 60382, or EN 60381-1. The other input value (i.e. the set point value) may be either a mechanical (position, force, etc.) or a standard signal.
Industrial-process control systems - Instruments with analogue inputs and two- or multi-state outputs - Part 1: Methods of evaluating performance
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61003-1:2004
STANDARD
junij 2004
Industrial-process control systems - Instruments with analogue inputs and two- or
multi-state outputs - Part 1: Methods of evaluating performance
ICS 25.040.40 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 61003-1
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2004
ICS 32.240.50; 25.040.40 Supersedes EN 61003-1:1993
English version
Industrial-process control systems -
Instruments with analogue inputs
and two- or multi-state outputs
Part 1: Methods of evaluating performance
(IEC 61003-1:2004)
Processus industriels - Systeme der industriellen
Instruments avec entrées analogiques Prozessleittechnik -
et sorties à deux ou plusieurs états Geräte mit analogen Eingängen
Partie 1: Méthodes d'évaluation und Zwei- oder Mehrpunktverhalten
des performances Teil 1: Verfahren zur Bewertung
(CEI 61003-1:2004) des Betriebsverhaltens
(IEC 61003-1:2004)
This European Standard was approved by CENELEC on 2004-03-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61003-1:2004 E
Foreword
The text of document 65B/516/FDIS, future edition 2 of IEC 61003-1, prepared by SC 65B, Devices, of
IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 61003-1 on 2004-03-01.
This European Standard supersedes EN 61003-1:1993.
It takes into account the common standardized basis specified in the EN 61298 series. Any test method
or procedure specified and described herein is referred to the corresponding Clause of the EN 61298
series. Any particular method or procedure not covered by the EN 61298 series is developed and
specified in this standard in accordance with the criteria stated in the EN 61298 series, as far as they are
applicable.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61003-1:2004 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61003-1:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-351 1998 International Electrotechnical Vocabulary- -
Part 351: Automatic control
IEC 60381-1 1982 Analogue signals for process control HD 452.1 S1 1984
systems
Part 1: Direct current signals
IEC 60382 1991 Analogue pneumatic signal for process EN 60382 1993
control systems
IEC 61010-1 2001 Safety requirements for electrical EN 61010-1 2001
equipment for measurement, control, and + corr. June 2002
laboratory use
Part 1: General requirements
IEC 61298-1 1995 Process measurement and control EN 61298-1 1995
devices - General methods and
procedures for evaluating performance
Part 1: General considerations
IEC 61298-2 1995 Part 2: Tests under reference conditions EN 61298-2 1995
IEC 61298-3 1998 Part 3: Tests for the effects of influence EN 61298-3 1998
quantities
IEC 61298-4 1995 Part 4: Evaluation report content EN 61298-4 1995
IEC 61326 2002 Electrical equipment for measurement, - -
control and laboratory use - EMC
requirements
INTERNATIONAL IEC
STANDARD 61003-1
Second edition
2004-01
Industrial-process control systems –
Instruments with analogue inputs and
two- or multi-state outputs –
Part 1:
Methods of evaluating performance
© IEC 2004 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale U
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue
– 2 – 61003-1 © IEC:2004(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Terms and definitions .7
4 General conditions for tests .8
4.1 Documentary information.8
4.2 Safety.8
4.3 Installation.8
4.4 Supply conditions.9
5 General testing procedures and precautions.9
5.1 Checking of calibration made prior to delivery .9
5.2 Set point.9
5.3 Switching differential.9
6 Test methods and procedures.9
6.1 Tests under reference conditions .9
6.2 Tests for the effects of influence quantities .12
6.3 Other tests.19
7 Multi-state instrument.21
7.1 Action.21
7.2 Tests.21
7.2.1 Characteristics of the multi-state instrument.21
7.2.2 Mutual influence of pairs of switching points.21
7.2.3 Determination of switching range .21
8 General observations.21
8.1 Protective finishes.21
8.2 Design features.22
8.3 Tools and equipment .22
9 Test report and summary of tests.23
10 Other considerations.27
10.1 Routine maintenance and adjustment .27
10.2 Repair.27
10.3 Partial evaluation.27
61003-1 © IEC:2004(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
INDUSTRIAL-PROCESS CONTROL SYSTEMS –
INSTRUMENTS WITH ANALOGUE INPUTS AND
TWO- OR MULTI-STATE OUTPUTS –
Part 1: Methods of evaluating performance
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61003-1 has been prepared by subcommittee 65B: Devices, of IEC
technical committee 65: Industrial-process measurement and control.
This second edition cancels and replaces the first edition issued in 1991 and constitutes a
technical revision. It takes into account the common standardized basis specified in the IEC
61298 series. Any test method or procedure specified and described herein is referred to the
corresponding Clause of the IEC 61298 series. Any particular method or procedure not covered
by the IEC 61298 series is developed and specified in this standard in accordance with the
criteria stated in the IEC 61298 series, as far as they are applicable.
– 4 – 61003-1 © IEC:2004(E)
The text of this standard is based on the following documents:
FDIS Report on voting
65B/516/FDIS 65B/524/RVD
Full information on the voting for t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.