EN 62841-2-9:2015/prAB:2024
(Amendment)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-9: Particular requirements for hand-held tappers and threaders
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-9: Particular requirements for hand-held tappers and threaders
IEC 62841-2-9:2015 applies to hand-held tappers and threaders. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Tapper, Threader, Internal Screw Threads, External Screw Threads This publication is to be read in conjunction with
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-9: Besondere Anforderungen für handgeführte Gewindebohrer und Gewindeschneider
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-9: Exigences particulières pour les taraudeuses et les fileteuses portatives
L'IEC 62841-2-9:2015 s'applique aux taraudeuses et les fileteuses portatives. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées en Annex K. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication. Mots-clés: taraudeuse, fileteuse, filetages internes, filetages externes Cette publication doit être lue conjointement avec la CEI 62841-1:2014.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-9. del: Posebne zahteve za ročne stroje za vrezovanje navojev - Dopolnilo AB
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2024
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-
9. del: Posebne zahteve za ročne stroje za vrezovanje navojev - Dopolnilo AB
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-9: Particular requirements for hand-held tappers and
threaders
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 2-9: Besondere Anforderungen für
handgeführte Gewindebohrer und Gewindeschneider
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 2-9: Exigences particulières pour les taraudeuses et les fileteuses
portatives
Ta slovenski standard je istoveten z: EN 62841-2-9:2015/prAB:2024
ICS:
25.100.50 Navojna rezalna orodja Taps and threading dies
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD DRAFT
EN 62841-2-9:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAB
February 2024
ICS 25.140.20 -
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-9: Particular
requirements for hand-held tappers and threaders
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-9: Exigences transportable Werkzeuge und Rasen- und
particulières pour les taraudeuses et les fileteuses Gartenmaschinen - Sicherheit - Teil 2-9: Besondere
portatives Anforderungen für handgeführte Gewindebohrer und
Gewindeschneider
This draft amendment prAB, if approved, will modify the European Standard EN 62841-2-9:2015; it is submitted to CENELEC members for
enquiry.
Deadline for CENELEC: 2024-05-03.
It has been drawn up by CLC/TC 116.
If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 79301 Ref. No. EN 62841-2-9:2015/prAB:2024 E
1 European foreword
2 This document (EN 62841-2-9:2015/prAB:2024) has been prepared by CLC/TC 116 “Safety and
3 environmental aspects of motor-operated electric tools”.
4 This document is currently submitted to the Enquiry.
5 The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 48 months
conflicting with this document have to be (to be confirmed or
withdrawn
modified when voting)
6 This document modifies by common modifications EN 62841-2-9:2015/prA1:2024, which consists of the
7 text of 116/xxx/CDV (future IEC 62841-2-9:2015/A1:202x) prepared by IEC/TC 116 “Safety of motor-
8 operated electric tools”.
9 EN 62841-2-9:2015/prA1:2024 together with prAB:2024 includes revisions to Table 4 in the main body of
10 the document as well as Annex K. It also clarifies that subclauses 21.18.1.2, 21.30, 21.35 and 23.3 of
11 EN 62841-1:2015 are not applicable for these tools.
12 This document has been prepared under a standardization request addressed to CENELEC by the
13 European Commission. The Standing Committee of the EFTA States subsequently approves these
14 requests for its Member States.
15 For relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this document.
16 1 Modification to Annex K, “Battery tools and battery packs”
17 Add the following new subclause:
18 “K.21.18.Z301 Isolation and disabling device
19 Tools with an integral battery shall be equipped
20 — with an isolation device to prevent the risk of injury from mechanical hazards during servicing or user
21 maintenance; or
22 — with a disabling device that prevents unintentional starting of the tool.
23 An isolation device shall
24 — provide disconnection of at le
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.