HD 129.6 S1:1984
(Main)Flanges for waveguides - Part 6: Relevant specifications for flanges for medium flat rectangular waveguides
Flanges for waveguides - Part 6: Relevant specifications for flanges for medium flat rectangular waveguides
Gives the mechanical requirements and contains two tables showing the metric and inch dimensions of types L and N.
Flansche für Hohlleiter - Teil 6: Allgemeine Anforderungen für Flansche für mittelflache Rechteck-Hohlleiter
Brides pour guides d'ondes - Partie 6: Spécifications particulières de brides pour guides d'ondes rectangulaires plats moyens
Donne les prescriptions mécaniques et contient deux tableaux indiquant les dimensions des brides de types L et N en millimètres et en inches.
[Not translated]
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST HD 129.6 S1:2004
01-januar-2004
[Not translated]
Flanges for waveguides - Part 6: Relevant specifications for flanges for medium flat
rectangular waveguides (IEC 60154-6:1983)
Flansche für Hohlleiter - Teil 6: Allgemeine Anforderungen für Flansche für mittelflache
Rechteck-Hohlleiter (IEC 60154-6:1983)
Brides pour guides d'ondes - Partie 6: Spécifications particulières de brides pour guides
d'ondes rectangulaires plats moyens (CEI 60154-6:1983)
Ta slovenski standard je istoveten z: HD 129.6 S1:1984
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST HD 129.6 S1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST HD 129.6 S1:2004
---------------------- Page: 2 ----------------------
SIST HD 129.6 S1:2004
---------------------- Page: 3 ----------------------
SIST HD 129.6 S1:2004
---------------------- Page: 4 ----------------------
SIST HD 129.6 S1:2004
NORME CEI
INTERNATIONALE IEC
60154-6
INTERNATIONAL
Première édition
STAN
DARD
First edition
1983-01
Brides pour guides d'ondes
Sixième partie:
Spécifications particulières
de brides pour
guides d'ondes rectangulaires
plats moyens
Flanges for waveguides
Part 6:
Relevant specifications for flanges
for medium flat rectangular waveguides
© IEC 1983 Droits de reproduction réservés —
Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni
No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun
any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo-
including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
L
PRICE CODE
International Electrotechnical Commission
IEC
MemnyHapoaHaa 3netsrporexwH4ecnaa HOMHCCHa
Pour prix, voir vigueur
catalogue en
• •
For price, see current catalogue
---------------------- Page: 5 ----------------------
SIST HD 129.6 S1:2004
154-6 © IEC 1983 3
CONTENTS
Page
5
FOREWORD
PREFACE 5
Clause
11
1. General
11
1.1 Standardized types
-11
1.2 Flange designation
11
2. Mechanical requirements
11
2.1 Dimensions
13
2.2 General requirements for assemblies
15
2.3 Additional requirements for unmounted flanges
type L
Flange
16
154 IEC —ULM 12
17
154 IEC — ULM 14-32
154 IEC — ULM 40-100 18
16
Drawings — Figures 1 to 3
19
TABLE I
Flange type N
20
154 IEC — PNM 14-40
21
1541EC—PNM45
154 IEC — PNM 48-70 22
20
Drawings — Figures 4 to 6
23
TABLE II
---------------------- Page: 6 ----------------------
SIST HD 129.6 S1:2004
154-6 © IEC 1983 5
INTERNATIONAL ELECTROTECHNICAL COMMISSION
FLANGES FOR WAVEGUIDES
Part 6: Relevant specifications for flanges for medium flat
rectangular waveguides
FOREWORD
1) The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the
National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in that
sense.
3) In order to promote international unification, the IEC expresses the wish that all National Committees should adopt the text
of the IEC recommendation for their national rules in so far as national conditions will permit. Any divergence between the
IEC recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
4) The IEC has not laid down any procedure concerning marking as an indication of approval and has no responsibility when an
item of equipment is declared to comply with one of its recommendations.
PREFACE
This standard has been prepared by Sub-Committee 46B: Waveguides and their Accessories, of IEC
Technical Committee No.46: Cables, Wires and Waveguides for Telecommunication Equipment.
It forms the sixth part of I E C Publication 154 dealing with flanges for waveguides, and should be used in
conjunction with Part 1: General Requirements and Measuring Methods.
Relevant specifications for other types of flanges have been issued in separate publications.
The general outline of this standard was first discussed at the meeting held in Bucharest in 1974. As a result
of this meeting, a revised draft was discussed at the meeting held in Stockholm in 1976. As a result of this
meeting, a draft, Document 46B(Central Office)82, was submitted to the National Committees for approval
under the Six Months' Rule in M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.