Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles

IEC/TS 80815-1:2008(E) applies to the selection of insulators, and the determination of their relevant dimensions, to be used in high-voltage systems with respect to pollution. This part of IEC 60815 gives general definitions, methods for the evaluation of pollution site severity (SPS) and outlines the principles to arrive at an informed judgement on the probable behaviour of a given insulator in certain pollution environments. This first edition of IEC/TS 60815-1 cancels and replaces IEC/TR 60815, which was issued as a technical report in 1986.

General Information

Status
Published
Publication Date
28-Oct-2008
Technical Committee
Drafting Committee
Current Stage
PPUB - Publication issued
Start Date
31-Jan-2009
Completion Date
29-Oct-2008
Ref Project

Buy Standard

Technical specification
IEC TS 60815-1:2008 - Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
English language
53 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC/TS 60815-1
Edition 1.0 2008-10
TECHNICAL
SPECIFICATION
Selection and dimensioning of high-voltage insulators intended for use in
polluted conditions –
Part 1: Definitions, information and general principles

IEC/TS 60815-1:2008(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC/TS 60815-1
Edition 1.0 2008-10
TECHNICAL
SPECIFICATION
Selection and dimensioning of high-voltage insulators intended for use in
polluted conditions –
Part 1: Definitions, information and general principles

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
XA
ICS 29.080.10 ISBN 978-2-88910-301-0
– 2 – TS 60815-1 © IEC:2008(E)
CONTENTS
FOREWORD.4
1 Scope and object.6
2 Normative references .7
3 Terms, definitions and abbreviations .7
3.1 Terms and definitions .7
3.2 Abbreviations .9
4 Proposed approaches for the selection and dimensioning of an insulator.9
4.1 Approach 1.10
4.2 Approach 2.10
4.3 Approach 3.10
5 Input parameters for the selection and dimensioning of insulators .12
6 System requirements.12
7 Environmental conditions.13
7.1 Identification of types of pollution .13
7.1.1 Type A pollution .13
7.1.2 Type B pollution .14
7.2 General types of environments .14
7.3 Pollution severity.15
8 Evaluation of site pollution severity (SPS) .15
8.1 Site pollution severity .15
8.2 Site pollution severity evaluation methods .16
8.3 Site pollution severity (SPS) classes .17
9 Insulation selection and dimensioning .20
9.1 General description of the process .20
9.2 General guidance on materials .21
9.3 General guidance on profiles.21
9.4 Considerations on creepage distance and insulator length .23
9.5 Considerations for exceptional or specific applications or environments .23
9.5.1 Hollow insulators .23
9.5.2 Arid areas.24
9.5.3 Proximity effects.24
9.5.4 Orientation .24
9.5.5 Maintenance and palliative methods .25
Annex A (informative) Flowchart representation of the design approaches.26
Annex B (informative) Pollution flashover mechanisms .29
Annex C (normative) Measurement of ESDD and NSDD .32
Annex D (normative) Evaluation of type B pollution severity.38
Annex E (normative) Directional dust deposit gauge measurements .40
Annex F (normative) Use of laboratory test methods.44
Annex G (normative) Deterministic and statistical approaches for artificial pollution

test severity and acceptance criteria .45
Annex H (informative) Example of a questionnaire to collect information on the
behaviour of insulators in polluted areas.48
Annex I (informative) Form factor.51
Annex J (informative) Correspondence between specific creepage distance and USCD.52

TS 60815-1 © IEC:2008(E) – 3 –
Bibliography.53

Figure 1 – Type A site pollution severity – Relation between ESDD/NSDD and SPS for
the reference cap and pin insulator .18
Figure 2 – Type A site pollution severity – Relation between ESDD/NSDD and SPS for
the reference long rod insulator .18
Figure 3 – Type B site pollution severity – Relation between SES and SPS for
reference insulators or a monitor .19
Figure C.1 – Insulator strings for measuring ESDD and NSDD.32
Figure C.2 – Wiping of pollutants on insulator surface.34
Figure C.3 – Value of b .35
Figure C.4 – Relation betweenσ and Sa .36
Figure C.5 – Procedure for measuring NSDD.37
Figure E.1 – Directional dust deposit gauges .40
Figure G.1 – Illustration for design based on the deterministic approach.46
Figure G.2 – Stress/strength concept for calculation of risk for pollution flashover .46
Figure H.1 – Form factor.51

Table 1 – The three approaches to insulator selection and dimensioning .11
Table 2 – Input parameters for insulator selection and dimensioning.12
Table 3 – Directional dust deposit gauge pollution index in relation to SPS class.19
Table 4 – Correction of site pollution severity class as a function of DDDG NSD levels.19
Table 5 – Examples of typical environments .20
Table 6 – Typical profiles and their main characteristics .22
Table D.1 – Directional dust deposit gauge pollution index in relation to site pollution
severity class.42
Table D.2 – Correction of site pollution severity class as a function of DDDG NSD
levels.42
Table J.1 – Correspondence between specific creepage distance and unified specific
creepage distance .52

– 4 – TS 60815-1 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SELECTION AND DIMENSIONING OF HIGH-VOLTAGE INSULATORS
INTENDED FOR USE IN POLLUTED CONDITIONS –

Part 1: Definitions, information and general principles

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.