IEC 60034-18-22:2000
(Main)Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
IEC 60034-18-22:2000 gives test procedures for the thermal evaluation and classification of changes and insulation component substitution in insulation systems used or proposed for use in a proven insulation system used in wire-wound windings. The test procedures are comparative in that the performance of a candidate system is compared to that of a reference system which has previously been proved by experience or has been evaluated by one of the procedures given in IEC 60034-18-21 and to which the change or substitution is intended.
Machines électriques tournantes - Partie 18-22: Evaluation fonctionnelle des systèmes d'isolation - Procédures d'essai pour enroulements à fils - Classification des modifications et des substitutions de composants d'isolation
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL IEC
STANDARD
60034-18-22
Second edition
2000-06
Rotating electrical machines –
Part 18-22:
Functional evaluation of insulation systems –
Test procedures for wire-wound windings –
Classification of changes and insulation
component substitutions
Machines électriques tournantes –
Partie 18-22:
Evaluation fonctionnelle des systèmes d'isolation –
Procédures d'essai pour enroulement à fils –
Classification des modifications et des substitutions
de composants d'isolations
Reference number
Numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series.
Consolidated publications
Consolidated versions of some IEC publications including amendments are
available. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the
base publication, the base publication incorporating amendment 1 and the base
publication incorporating amendments 1 and 2.
Validity of this publication
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology.
Information relating to the date of the reconfirmation of the publication is available
in the IEC catalogue.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is to be found at the following IEC sources:
• IEC web site*
•
Catalogue of IEC publications
Published yearly with regular updates
(On-line catalogue)*
• IEC Bulletin
Available both at the IEC web site* and as a printed periodical
Terminology, graphical and letter symbols
For general terminology, readers are referred to IEC 60050: International
Electrotechnical Vocabulary (IEV).
For graphical symbols, and letter symbols and signs approved by the IEC for
general use, readers are referred to publications IEC 60027: Letter symbols to be
used in electrical technology, IEC 60417: Graphical symbols for use on equipment.
Index, survey and compilation of the single sheets and IEC 60617: Graphical symbols
for diagrams.
* See web site address on title page.
INTERNATIONAL IEC
STANDARD
60034-18-22
Second edition
2000-06
Rotating electrical machines –
Part 18-22:
Functional evaluation of insulation systems –
Test procedures for wire-wound windings –
Classification of changes and insulation
component substitutions
Machines électriques tournantes –
Partie 18-22:
Evaluation fonctionnelle des systèmes d'isolation –
Procédures d'essai pour enroulement à fils –
Classification des modifications et des substitutions
de composants d'isolations
IEC 2000 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
Commission Electrotechnique Internationale
PRICE CODE
N
International Electrotechnical Commission
For price, see current catalogue
– 2 – 60034-18-22 IEC:2000(E)
CONTENTS
Page
FOREWORD . 3
INTRODUCTION .5
Clause
1 Scope . 6
2 Normative references. 6
3 General guidelines. 6
3.1 Category I insulation components . 6
3.2 Category II insulation components . 7
3.3 Definition of generic identity. 7
4 Documentation. 8
5 General substitution procedures. 8
6 Component substitution category . 8
6.1 Category I component substitution . 8
6.2 Category II component substitution . 10
7 Sealed tube test procedure . 10
7.1 General. 10
7.2 Test apparatus. 11
7.3 Sample preparation. 11
7.4 Contents of tubes. 11
7.5 Preparation of tubes . 12
7.6 Thermal conditioning. 12
7.7 Opening procedure . 12
7.8 Evaluation of samples. 13
7.9 Requirement . 13
Table 1 – Thermal ageing test methods for varnish . 9
Figure 1 – Test apparatus . 14
60034-18-22 IEC:2000(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –
Part 18-22: Functional evaluation of insulation systems –
Test procedures for wire-wound windings – Classification of changes
and insulation component substitutions
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-18-22 has been prepared by subcommittee 2J:
Classification of insulation systems for rotating machinery, of IEC technical committee 2:
Rotating electrical machines.
This second edition cancels and replaces the first edition published in 1996 of which it
constitutes a technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
2/1088/FDIS 2/1096/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
– 4 – 60034-18-22 IEC:2000(E)
The committee has decided that the contents of this publication will remain unchanged until
2005. At this date, the publication will be
reconfirmed;
withdrawn;
replaced by a revised edition, or
amended.
A bilingual version of this publication may be issued at a later date.
It forms part of a series under the general title Rotating electrical machines:
Part 18-1:1992, Functional evaluation of insulation systems – General guidelines
Part 18-21:1992, Functional evaluation of insulation systems – Test procedures for wire-
wound windings – Thermal evaluation and classification
Part 18-31:1992, Functional evaluation of insulation systems – Test procedures for form-
wound windings – Thermal evaluation and classification of insulation systems used in
machines up to and including 50 MVA and 15 kV
Part 18-32:1995, Functional evaluation of insulation systems – Test procedures for form-
wound windings – Electrical evaluation of insulation systems used in machines up to and
including 50 MVA and 15 kV
Part 18-33:1995, Functional evaluation of insulation systems – Test procedures for form-
wound windings – Multifactor functional evaluation – Endurance under combined thermal and
electrical stresses of insulation systems used in machines up to and including 50 MVA
and 15 kV
60034-18-22 IEC:2000(E) – 5 –
INTRODUCTION
IEC 60034-18-1 presents general principles for evaluation and classification of insulation
systems used in rotating electrical machines. Unless the procedures of this part indicate
otherwise, the principles of IEC 60034-18-1 should be followed.
IEC 60034-18-21 deals with the thermal evaluation and classification of insulation systems
for wire-wound windings in respect of normal procedures as referred to in 5.3.2.1 of
IEC 60034-18-1.
This part of IEC 60034 is concerned with procedures of verification of the effects of changes
in insulation systems for wire-wound windings covered by 5.3.2.2 of IEC 60034-18-1.
– 6 – 60034-18-22 IEC:2000(E)
ROTATING ELECTRICAL MACHINES –
Part 18-22: Functional evaluation of insulation systems –
Test procedures for wire-wound windings – Classification of changes
and insulation component substitutions
1 Scope
This part of IEC 60034 gives test procedures for the thermal evaluation and classification of
changes and insulation component substitution in insulation systems used or proposed for
use in a proven insulation system used in wire-wound windings. The test procedures are
comparative in that the performance of a candidate system is compared to that of a reference
system which has previously been proved by experience or has been evaluated by one of the
procedures given in 60034-18-21 and to which the change or substitution is intended.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this International Standard. For dated references, subsequent
amendments to, or revisions of, any of these publications do not apply. However, parties to
agreements based on this International Standard are encouraged to investigate the possibility
of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of IEC
and ISO maintain registers of currently valid International Standards.
IEC 60034-18-21:1992, Rotating electric machines – Part 18: Functional evaluation of
insulation systems – Section 21: Test procedures for wire-wound windings – Thermal
evaluation and classification
IEC 60172:1987, Test procedure for the determination of the temperature index of enamelled
winding wires
IEC 60216, Guide for the determination of thermal endurance properties of electrical
insulating materials
IEC 60317, Specifications for particular types of winding wires
IEC 61033:1991, Test methods for the determination of bond strength of impregnating agents
to an enamelled wire substrate
3 General guidelines
3.1 Category I insulation components
3.1.1 Phase insulation and ground insulation
Insulation separating the windings from each other or from the magnetic core, for example
slot liners, but not wedges, closures or top of slot packers all of which are considered as
category II components (see 3.2).
60034-18-22 IEC:2000(E) – 7 –
3.1.2 Turn (conductor) insulation
The resinous (enamel) coating or wrapped insulation, fibrous or film, on winding wire.
3.1.3 Impregnating varnishes
These include both solvented and solventless varnishes.
3.1.4 Encapsulant
Moulded or cast insulation which completely encases the insulation system and which is the
only barrier between the winding and the outer surface of the motor.
3.2 Category II insulation components
Category II components include any constituent of an insulation system not covered by 3.1,
as listed below. If the testing organization wants to consider some of these components as
category I insulation components, it may do so.
a) Series/parallel winding insulation as used on multi-voltage windings
b) Insulation between auxiliary and main winding as used on single-phase
...
IEC 60034-18-22
Edition 2.0 2000-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines –
Part 18-22: Functional evaluation of insulation systems – Test procedures for
wire-wound windings – Classification of changes and insulation component
substitutions
Machines électriques tournantes –
Partie 18-22: Evaluation fonctionnelle des systèmes d’isolation – Procédures
d’essai pour enroulements à fils – Classification des modifications et des
substitutions de composants d’isolation
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60034-18-22
Edition 2.0 2000-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines –
Part 18-22: Functional evaluation of insulation systems – Test procedures for
wire-wound windings – Classification of changes and insulation component
substitutions
Machines électriques tournantes –
Partie 18-22: Evaluation fonctionnelle des systèmes d’isolation – Procédures
d’essai pour enroulements à fils – Classification des modifications et des
substitutions de composants d’isolation
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
N
CODE PRIX
ICS 29.080.01; 29.160.01 ISBN 2-8318-5745-7
– 2 – 60034-18-22 © CEI:2000
SOMMAIRE
AVANT-PROPOS.4
INTRODUCTION.8
1 Domaine d'application .10
2 Références normatives.10
3 Principes directeurs généraux .10
3.1 Composants d'isolation de catégorie I .10
3.2 Composants d'isolation de catégorie II .12
3.3 Définition de l'identité générique .12
4 Documentation .14
5 Procédures générales de substitution .14
6 Catégorie de substitution de composant .14
6.1 Substitution de composant de catégorie I .14
6.2 Substitution de composant de catégorie II .18
7 Procédure d'essai avec tube scellé.18
7.1 Généralités.18
7.2 Matériel d'essai .20
7.3 Préparation de l'échantillon .20
7.4 Contenu des tubes .20
7.5 Préparation des tubes .22
7.6 Conditionnement thermique.22
7.7 Procédure d'ouverture .24
7.8 Evaluation des échantillons .24
7.9 Condition requise .24
Figure 1 – Appareil d'essai.26
Tableau 1 – Méthodes d'essai de vieillissement thermique pour les vernis.16
60034-18-22 © IEC:2000 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9
1 Scope.11
2 Normative references .11
3 General guidelines .11
3.1 Category I insulation components.11
3.2 Category II insulation components.13
3.3 Definition of generic identity .13
4 Documentation .15
5 General substitution procedures .15
6 Component substitution category.15
6.1 Category I component substitution.15
6.2 Category II component substitution .19
7 Sealed tube test procedure.19
7.1 General .19
7.2 Test apparatus .21
7.3 Sample preparation .21
7.4 Contents of tubes .21
7.5 Preparation of tubes .23
7.6 Thermal conditioning .23
7.7 Opening procedure.25
7.8 Evaluation of samples .25
7.9 Requirement.25
Figure 1 – Test apparatus .27
Table 1 – Thermal ageing test methods for varnish.17
– 4 – 60034-18-22 © CEI:2000
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
MACHINES ÉLECTRIQUES TOURNANTES –
Partie 18-22: Evaluation fonctionnelle des systèmes d'isolation –
Procédures d'essai pour enroulements à fils –
Classification des modifications et des substitutions
de composants d'isolation
AVANT-PROPOS
1) La Commission Electrotechnique Internationale (CEI) est une organisation mondiale de normalisation
composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de la CEI). La CEI a
pour objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les
domaines de l'électricité et de l'électronique. A cet effet, la CEI – entre autres activités – publie des Normes
internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au
public (PAS) et des Guides (ci-après dénommés "Publication(s) de la CEI"). Leur élaboration est confiée à des
comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les
organisations internationales, gouvernementales et non gouvernementales, en liaison avec la CEI, participent
également aux travaux. La CEI collabore étroitement avec l'Organisation Internationale de Normalisation (ISO),
selon des conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de la CEI concernant les questions techniques représentent, dans la mesure
du possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de la CEI
intéressés sont représentés dans chaque comité d’études.
3) Les Publications de la CEI se présentent sous la forme de recommandations internationales et sont agréées
comme telles par les Comités nationaux de la CEI. Tous les efforts raisonnables sont entrepris afin que la CEI
s'assure de l'exactitude du contenu technique de ses publications; la CEI ne peut pas être tenue responsable
de l'éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final.
4) Dans le but d'encourager l'uniformité internationale, les Comités nationaux de la CEI s'engagent, dans toute la
mesure possible, à appliquer de façon transparente les Publications de la CEI dans leurs publications
nationales et régionales. Toutes divergences entre toutes Publications de la CEI et toutes publications
nationales ou régionales correspondantes doivent être indiquées en termes clairs dans ces dernières.
5) La CEI n’a prévu aucune procédure de marquage valant indication d’approbation et n'engage pas sa
responsabilité pour les équipements déclarés conformes à une de ses Publications.
6) Tous les
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.