iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 62011-2:2004

(Main)

Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test

Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test

Deals with the test methods for industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes. The test methods include the following: a) Dimensions - External dimensions - Internal dimensions - Wall thickness - Departure from straightness - Applicable to all tubes and rods b) Mechanical tests - Flexural strength perpendicular to laminations (rods only) - Axial compressive strength (tubes only) c) Electrical tests - General - Insulation resistance after immersion in water d) Other tests - Water absorption - Density

Matériaux isolants - Tubes et barres industriels, rigides, moulés, stratifiés, de sections transversales rectangulaires ou hexagonales, à base de résines thermodurcissables, à usages électriques - Partie 2: Méthodes d'essai

Traite des méthodes d'essai destinées aux tubes et barres industriels, rigides, moulés, stratifiés, de sections transversales rectangulaires ou hexa-gonales, à base de résines thermodurcissables, à usages électriques. Les méthodes d'essai couvrent les suivantes: a) Dimensions - Dimensions extérieures - Dimensions intérieures - Epaisseur de paroi - Défaut de rectitude - S'applique à tous les tubes et à toutes les barres b) Essais mécaniques - Résistance à la flexion perpendiculairement aux couches (barres uniquement) - Résistance à la compression axiale (pour les tubes uniquement c) Essais électriques - Généralités - Résistance d'isolement après immersion dans l'eau d) Autres essais - Absorption d'eau - Masse volumique

General Information

Status
Published
Publication Date
07-Jan-2004
ICS
01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
29.035.20 - Plastics and rubber insulating materials
Technical Committee
TC 15 - Solid electrical insulating materials
Drafting Committee
WG 6 - TC 15/WG 6
Current Stage
PPUB - Publication issued
Start Date
29-Feb-2004
Completion Date
08-Jan-2004
Ref Project

Buy Standard

IEC 62011-2:2004 - Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of testIEC 62011-2:2004 - Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test
PreviousNext
Standard
IEC 62011-2:2004 - Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test
English and French language
31 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NORME CEI
INTERNATIONALE
IEC



62011-2
INTERNATIONAL


Première édition
STANDARD

First edition
2004-01

Matériaux isolants –
Tubes et barres industriels, rigides,
moulés, stratifiés, de sections transversales
rectangulaires ou hexagonales, à base de résines
thermodurcissables, à usages électriques –
Partie 2:
Méthodes d'essai

Insulating materials –
Industrial, rigid, moulded, laminated tubes
and rods of rectangular and hexagonal
cross-section, based on thermosetting resins
for electrical purposes –
Part 2:
Methods of test
Numéro de référence
Reference number
CEI/IEC 62011-2:2004

---------------------- Page: 1 ----------------------
Numérotation des publications Publication numbering
Depuis le 1er janvier 1997, les publications de la CEI As from 1 January 1997 all IEC publications are
sont numérotées à partir de 60000. Ainsi, la CEI 34-1 issued with a designation in the 60000 series. For
devient la CEI 60034-1. example, IEC 34-1 is now referred to as IEC 60034-1.
Editions consolidées Consolidated editions
Les versions consolidées de certaines publications de la The IEC is now publishing consolidated versions of its
CEI incorporant les amendements sont disponibles. Par publications. For example, edition numbers 1.0, 1.1
exemple, les numéros d’édition 1.0, 1.1 et 1.2 indiquent and 1.2 refer, respectively, to the base publication,
respectivement la publication de base, la publication de the base publication incorporating amendment 1 and
base incorporant l’amendement 1, et la publication de the base publication incorporating amendments 1
base incorporant les amendements 1 et 2. and 2.
Informations supplémentaires Further information on IEC publications
sur les publications de la CEI
Le contenu technique des publications de la CEI est The technical content of IEC publications is kept
constamment revu par la CEI afin qu'il reflète l'état under constant review by the IEC, thus ensuring that
actuel de la technique. Des renseignements relatifs à the content reflects current technology. Information
cette publication, y compris sa validité, sont dispo- relating to this publication, including its validity, is
nibles dans le Catalogue des publications de la CEI available in the IEC Catalogue of publications
(voir ci-dessous) en plus des nouvelles éditions, (see below) in addition to new editions, amendments
amendements et corrigenda. Des informations sur les and corrigenda. Information on the subjects under
sujets à l’étude et l’avancement des travaux entrepris consideration and work in progress undertaken by the
par le comité d’études qui a élaboré cette publication, technical committee which has prepared this
ainsi que la liste des publications parues, sont publication, as well as the list of publications issued,
également disponibles par l’intermédiaire de: is also available from the following:
• Site web de la CEI (www.iec.ch) • IEC Web Site (www.iec.ch)
• Catalogue des publications de la CEI • Catalogue of IEC publications
Le catalogue en ligne sur le site web de la CEI The on-line catalogue on the IEC web site
(www.iec.ch/searchpub) vous permet de faire des (www.iec.ch/searchpub) enables you to search by a
recherches en utilisant de nombreux critères, variety of criteria including text searches,
comprenant des recherches textuelles, par comité technical committees and date of publication. On-
d’études ou date de publication. Des informations en line information is also available on recently
ligne sont également disponibles sur les nouvelles issued publications, withdrawn and replaced
publications, les publications remplacées ou retirées, publications, as well as corrigenda.
ainsi que sur les corrigenda.
• IEC Just Published • IEC Just Published
Ce résumé des dernières publications parues This summary of recently issued publications
(www.iec.ch/online_news/justpub) est aussi dispo- (www.iec.ch/online_news/justpub) is also available
nible par courrier électronique. Veuillez prendre by email. Please contact the Customer Service
contact avec le Service client (voir ci-dessous) Centre (see below) for further information.
pour plus d’informations.
• Service clients • Customer Service Centre
Si vous avez des questions au sujet de cette If you have any questions regarding this
publication ou avez besoin de renseignements publication or need further assistance, please
supplémentaires, prenez contact avec le Service contact the Customer Service Centre:
clients:
Email: custserv@iec.ch Email: custserv@iec.ch
Tél: +41 22 919 02 11 Tel: +41 22 919 02 11
Fax: +41 22 919 03 00 Fax: +41 22 919 03 00
.

---------------------- Page: 2 ----------------------
NORME CEI
INTERNATIONALE
IEC



62011-2
INTERNATIONAL


Première édition
STANDARD

First edition

2004-01


Matériaux isolants –
Tubes et barres industriels, rigides,
moulés, stratifiés, de sections transversales
rectangulaires ou hexagonales, à base de résines
ther
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 60684-3-283:2019 ED2(Main)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation

IEC 60684-3-283:2019 is available as IEC 60684-3-283:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60684-3-283:2019 gives the requirements for two types of heat-shrinkable, polyolefin sleeving for bus-bar insulation, with a nominal shrink ratio of 2,5:1. This sleeving has been found suitable up to temperatures of 100 °C.
Type A: Medium wall - internal diameter up to 170,0 mm typically
Type B: Thick wall - internal diameter up to 165,0 mm typically
These sleevings are normally supplied in colour, red or brown. Since these types of sleeving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) provides guidance to the range of sizes available. The actual size and wall thickness will be agreed between the user and supplier depending on the electric strength of the installed tubing offered and the requirements of the user. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This second edition cancels and replaces the first edition published in 2010 and Amendment 1:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- change of moulded plaque thickness for resistance to tracking and weathering tests to (6 ± 0,5) mm.
Keywords: Heat-shrinkable, polyolefin sleeving for bus-bar insulation

  • Standard
    25 pages
    English and French language
    sale 15% off
IEC
IEC 60684-3-280:2019 ED2(Main)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving, anti-tracking

IEC 60684-3-280:2019 is available as IEC 60684-3-280:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 69684-3-280:2019 gives the requirements for heat-shrinkable, polyolefin sleeving, anti-tracking with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures up to 100 °C. Typically: medium wall, internal diameter up to 110 mm. This sleeving is normally supplied in the colours red or brown. Since these types of sleeving cover a significantly large range of sizes and wall thicknesses, Annex A (Table A.1) provides guidance on the range of sizes available. The actual size will be agreed between the user and the supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This sleeving is designed to be used in medium voltage cable accessories and as such electrical performance willbe proven as part of the assembly. Examples of this are described in HD 629.1 and IEC 60502 (all parts). This second edition cancels and replaces the first edition published in 2010 and Amendment 1:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- change of moulded plaque thickness for resistance to tracking and weathering tests to (6 ± 0,5) mm.
Keywords: Heat-shrinkable, polyolefin sleeving, anti-tracking

  • Standard
    25 pages
    English and French language
    sale 15% off
IEC
IEC 60684-3-247:2019 ED2(Main)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall

IEC 60684-3-247:2019 is available as IEC 60684-3-247:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60684-3-247:2019 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 °C.
- Type A: Medium wall, internal diameter up to 200,0 mm typically.
- Type B: Thick wall, internal diameter up to 200,0 mm typically.
These sleevings are normally supplied in colour black. Since these types of sleving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) provides a guide to the range of sizes available. The actual size will be agreed between the user and supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This second edition cancels and replaces the first edition published in 2011 and Amendment 1:2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous editions:
- removal of the colour fastness to light test, as this is covered by the test for carbon black content;
- change of low temperature flexibility test to -20 °C to align with sheet 214;
- change of final conditioning temperature of peel strength samples to 200 ºC to align with the temperature in Clause 5;
- removal of the fungus resistance test as there is no evidence that fungus growth is an issue either by testing or in use.
Keywords: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall

  • Standard
    28 pages
    English and French language
    sale 15% off
IEC
IEC 60684-3-214:2019 ED4(Main)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall

IEC 60684-3-214:2019 is available as IEC 60684-3-214:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 15-60684-3-214:2019 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 °C.
- Type A: Medium wall - internal diameter up to 200 mm typically.
- Type B: Thick wall - internal diameter up to 200 mm typically.
These sleevings are normally supplied in colour black. Since these types of sleeving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) of this document provides a guide to the range of sizes available. The actual size will be agreed between the user and supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition:
- removal of colour fastness to light test, as this is covered by the test for carbon black content.
Keywords: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall

  • Standard
    25 pages
    English and French language
    sale 15% off
IEC
IEC 60684-3-216:2019 ED2(Main)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame- retarded, limited-fire-hazard sleeving

IEC 60684-3-216:2019 is available as IEC 60684-3-216:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60684-3-216: 2019 gives the requirements for four types of heat-shrinkable, flame-retarded, limited-fire-hazard sleeving with a thermal endurance rating of 105 °C as shown below.
Class A: thin wall shrink ratio 2:1 internal diameter up to 102,0 mm
Class B: medium wall shrink ratio 2:1 internal diameter up to 60,0 mm
Class C: thick wall shrink ratio 2:1 internal diameter up to 51,0 mm
Class D: medium wall shrink ratio 3:1 internal diameter up to 40,0 mm
These sleevings are normally supplied in the following colours: black, red, green, blue, white, yellow and green/yellow. Sizes or colours other than those listed in this document are available as custom items. These items are considered to comply with this document if they comply with the property requirements listed in Tables 5, 6, 7 and 8, excluding dimensions and mass. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This second edition cancels and replaces the first edition published in 2001, Amendment 1:2005 and Amendment 2:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
1. the temperature at which the sleeving is shrunk in a forced-air circulation oven for (5 ± 1) min has been increased from (150 ± 5) °C to (200 ± 5) °C.
Keywords: flexible insulating sleeving for electrical purposes

  • Standard
    32 pages
    English and French language
    sale 15% off
IEC
IEC 62677-3-103:2019 ED1(Main)
Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 103: Heat-shrinkable, polyolefin, conductive moulded shapes for medium voltage applications

IEC 62677-3-103:2019 is applicable to heat shrinkable low and medium voltage moulded shapes, conductive, in a range of configurations suitable for environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 ºC and 100 ºC. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will need to be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in EN 50393, HD 629 and IEC 60502 (all parts).
Keywords: heat shrinkable, polyolefin, conductive moulded shapes for medium voltage applications

  • Standard
    21 pages
    English and French language
    sale 15% off
IEC
IEC 60674-2:2016/AMD1:2019(Amendment)
Amendment 1 - Specification for plastic films for electrical purposes - Part 2: Methods of test
  • Standard
    5 pages
    English and French language
    sale 15% off
IEC
IEC 60674-3-2:2019 ED2(Main)
Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation

IEC 60674-3-2:2019 gives the requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.
Keywords: plastic films for electrical purposes, balanced biaxially oriented polyethylene terephthalate (PET) films

  • Standard
    25 pages
    English and French language
    sale 15% off
IEC
IEC 62677-3-101:2018 ED1(Main)
Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications

IEC 62677-3-101:2018 is applicable to heat shrinkable low voltage moulded shapes in a range of configurations suitable for insulation, environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 °C and 100 °C. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options. The material is available in two types:
- Type A - Flame retardant
- Type B - Not flame retardant
Materials which conform to this document meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and will not be based on this document alone. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and, as such, electrical performance will be proven as part of the assembly. Examples of this are described in EN 50393, HD 629 and IEC 60502-1.

  • Standard
    21 pages
    English and French language
    sale 15% off
IEC
IEC 62677-3-102:2018 ED1(Main)
Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications

IEC 62677-3-102:2018 is applicable to heat shrinkable medium voltage moulded shapes in a range of configurations suitable for insulation, environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 °C and 100 °C. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options. Materials which conform to this document meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and will not be based on this document alone. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in IEC 60502 (all parts), EN 50393 and HD 629.
Keywords: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications

  • Standard
    21 pages
    English and French language
    sale 15% off