Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications

IEC 62677-3-101:2018 is applicable to heat shrinkable low voltage moulded shapes in a range of configurations suitable for insulation, environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 °C and 100 °C. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options. The material is available in two types:
- Type A - Flame retardant
- Type B - Not flame retardant
Materials which conform to this document meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and will not be based on this document alone. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and, as such, electrical performance will be proven as part of the assembly. Examples of this are described in EN 50393, HD 629 and IEC 60502-1.

Profilés thermorétractables basse et moyenne tensions - Partie 3: Spécification pour matériaux particuliers - Feuille 101: Profilés thermorétractables en polyoléfine pour applications basse tension

IEC 62677-3-101:2018 est applicable aux profilés thermorétractables basse tension dans une gamme de configurations adaptées à l’isolement, aux éléments d’étanchéité contre les intempéries, à la protection mécanique, aux dispositifs compensateurs de traction pour extrémités de câbles de puissance, aux joints et aux extrémités d'arrêt. Ces profilés sont jugés adaptés pour des utilisations dans la plage de températures de –40 °C à 100 °C. Les profilés peuvent être fournis avec un adhésif prérevêtu. L'Annexe A fournit un guide sur la compatibilité des adhésifs et la performance en température. Les fabricants/fournisseurs peuvent être consultés pour les options.
Deux types de matériaux sont disponibles:
- Type A - Retardateur de flamme
- Type B - Non retardateur de flamme
Les matériaux conformes au présent document satisfont à des niveaux établis de performance. Cependant, le choix d’un matériau par un utilisateur, pour une application spécifique, sera fondé sur les exigences réelles nécessaires pour obtenir une performance adéquate pour l'application concernée, et ne sera pas fondé sur ce seul document. Les essais spécifiés sont conçus pour contrôler la qualité des profilés, mais il est reconnu qu'ils sont conçus pour être utilisés dans des accessoires de câbles basse et moyenne tensions et, à ce titre, la performance électrique sera prouvée dans le cadre de l'assemblage. Des exemples sont développés dans l'EN 50393, le HD 629 et l'IEC 60502-1.
Mots clés: Profilés thermorétractables en polyoléfine pour applications basse tension

General Information

Status
Published
Publication Date
09-Jan-2018
Current Stage
PPUB - Publication issued
Start Date
26-Jan-2018
Completion Date
10-Jan-2018
Ref Project

Buy Standard

Standard
IEC 62677-3-101:2018 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications
English and French language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 62677-3-101
®

Edition 1.0 2018-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Heat-shrinkable low and medium voltage moulded shapes –
Part 3: Specification for individual materials – Sheet 101: Heat-shrinkable,
polyolefin moulded shapes for low voltage applications

Profilés thermorétractables basse et moyenne tensions –
Partie 3: Spécification pour matériaux particuliers – Feuille 101: Profilés
thermorétractables en polyoléfine pour applications basse tension

IEC 62677-3-101:2018-01(en-fr)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2018 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.


Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.


A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 21 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.


Recherche de publications IEC -
Glossaire IEC - std.iec.ch/glossary
webstore.iec.ch/advsearchform
67 000 entrées terminologiques électrotechniques, en anglais
La recherche avancée permet de trouver des publications IEC et en français, extraites des articles Termes et Définitions des
en utilisant différents critères (numéro de référence, texte, publications IEC parues depuis 2002. Plus certaines entrées
comité d’études,…). Elle donne aussi des informations sur les antérieures extraites des publications des CE 37, 77, 86 et
projets et les publications remplacées ou retirées. CISPR de l'IEC.

IEC Just Published - webstore.iec.ch/justpublished Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just Si vous désirez nous donner des commentaires sur cette
Published détaille les nouvelles publications parues. publication ou si vous avez des questions contactez-nous:
Disponible en ligne et aussi une fois par mois par email. sales@iec.ch.

---------------------- Page: 2 ----------------------
IEC 62677-3-101

®


Edition 1.0 2018-01




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Heat-shrinkable low and medium voltage moulded shapes –

Part 3: Specification for individual materials – Sheet 101: Heat-shrinkable,

polyolefin moulded shapes for low voltage applications




Profilés thermorétractables basse et moyenne tensions –

Partie 3: Spécification pour matériaux particuliers – Feuille 101: Profilés


thermorétractables en polyoléfine pour applications basse tension












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.035.20  29.035.01 ISBN 978-2-8322-5212-3



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – IEC 62677-3-101:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designation . 7
5 Conditions of test for dimensions . 7
6 Requirements . 7
7 Moulded shapes material conformance . 7
Annex A (informative) Adhesive compatibility guide . 10
Bibliography . 11

Table 1 – Property requirements . 8
Table 2 – Resistance to selected fluids . 9
Table 3 – Additional property requirements . 9
Table A.1 – Adhesive compatibility guide . 10

---------------------- Page: 4 ----------------------
IEC 62677-3-101:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HEAT-SHRINKABLE LOW AND MEDIUM
VOLTAGE MOULDED SHAPES –

Part 3: Specification for individual materials –
Sheet 101: Heat-shrinkable, polyolefin moulded shapes
for low voltage applications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62677-3-101 has been prepared by IEC technical committee 15:
Solid electrical insulating materials.
The text of this International Standard is based on the following documents:
FDIS Report on voting
15/814/FDIS 15/820/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 5 ----------------------
– 4 – IEC 62677-3-101:2018 © IEC 2018
A list of all parts in the IEC 62677 series, published under the general title Heat-shrinkable
low and medium voltage moulded shapes, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 6 ----------------------
IEC 62677-3-101:2018 © IEC 2018 – 5 –
INTRODUCTION
This part of IEC 62677 is one of a series that deals with heat shrinkable low and medium
voltage moulded shapes. The series consists of three parts:
Part 1: General requirements (IEC 62677-1);
Part 2: Methods of test (IEC 62677-2);
Part 3: Specification for individual materials (IEC 62677-3).
This standard gives one of the sheets comprising Part 3 as follows:
Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications
Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage
applications
Sheet 103: Heat-shrinkable, polyolefin, semi-conductive moulded shapes for 8 medium
voltage applications

---------------------- Page: 7 ----------------------
– 6 – IEC 62677-3-101:2018 © IEC 2018
HEAT-SHRINKABLE LOW AND MEDIUM
VOLTAGE MOULDED SHAPES –

Part 3: Specification for individual materials –
Sheet 101: Heat-shrinkable, polyolefin moulded shapes
for low voltage applications



1 Scope
This part of IEC 62677 is applicable to heat shrinkable low voltage moulded shapes in a range
of configurations suitable for insulation, environmental sealing, mechanical protection, strain
relief for power cable terminations, joints and stop ends. These moulded shapes have been
found suitable for use for temperatures between –40 °C and 100 °C.
The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive
compatibility and temperature performance is given in Annex A. The manufacturers/suppliers
can be consulted for options.
The material is available in two types:
Type A – Flame retardant
Type B – Not flame retardant
Materials which conform to this document meet established levels of performance. However,
the selection of a material by a user for a specific application will be based on the actual
requirements necessary for adequate performance in that application and will not be based on
this document alone.
The tests specified are designed to control the quality of the moulded shapes but it is
recognized that they are designed to be used in low and medium voltage cable accessories
and, as such, electrical performance will be proven as part of the assembly. Examples of this
are described in EN 50393, HD 629 and IEC 60502-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60296, Fluids for electrotechnical applications – Unused mineral insulating oils for
transformers and switchgear
IEC 60757, Code for designation of colours
IEC 62677-1, Heat shrinkable low and medium voltage moulded shapes – Part 1: General
requirements
IEC 62677-2, Heat shrinkable low and medium voltage moulded shapes – Part 2: Methods of
test
ISO 846, Plastics: Evaluation of the action of microorganisms

---------------------- Page: 8 ----------------------
IEC 62677-3-101:2018 © IEC 2018 – 7 –
ISO 868, Plastics and ebonite – Determination of indentation hardness by means of a
durometer (Shore hardness)
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Designation
The moulded shapes shall be identified by the following designation:
Description IEC IEC part IEC sheet Type Adhesive Colour Table 3
publication number number code
number
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Suppliers part IEC 62677 - 3 - 101 -A -U - BK X
number

Any colour abbreviation shall comply with IEC 60757, where applicable. Non-standard colours
shall be written out in full.
See Annex A for adhesive nomenclature.
The addition of "X" at the end of the designation indicates that the properties contained in
Table 3 have been agreed upon between the user and supplier.
NOTE This information is for packaging labelling only, in accordance with IEC 62677-1.
5 Conditions of test for dimensions
The moulded shapes shall be shrunk in a forced air circulation oven at 200 °C ± 5 K for
(10 ± 1) min.
6 Requirements
In addition to the general requirements given in IEC 62677-1, the heat-shrinkable moulded
shapes shall comply with the requirements in Table 1 and, where applicable, Table 3.
7 Moulded shapes material conformance
Conformance with the requirements of this document shall be based on the results from test
sheets, (2 ± 0,15) mm thick, unless otherwise specified, which shall be prepared from the
same cross-linked heat-shrinkable material that is used to manufacture the heat shrinkable
moulded shapes.

---------------------- Page: 9 ----------------------
– 8 – IEC 62677-3-101:2018 © IEC 2018
Table 1 – Property requirements
Property IEC 62677-2:2017 Units Max. Requirements Remarks
clause or or
subclause Min.
Dimensions 6 mm Min. To be agreed See Clause 5
between purchaser
Min.
and supplier
Heat shock 7  Heat at
175 °C ± 5 K
Tensile strength 10.1 and 10.2 MPa Min. 8
Elongation at break 10.1 and 10.2 % Min. 200
Bending at low 8 - - No cracking
Test at –40 °C
temperature shall be visible
The mandrel
shall be between 20
and 22 times the
sample thickness.
Dimensional stability 9 - - The dimensions shall See Clause 5
on storage remain as agreed
between purchaser
and supplier
Tensile strength 10.1 and 10.2 MPa Min. 10 Use a jaw
separation rate of
Elongation at break 10.1 and 10.2 % Min. 300
100 mm/min.
Secant modulus 11 MPa Min. 80
at 2% elongation
Max. 150
Electric strength 12 kV/mm Min. 10


12
Volume resistivity 13 Ω⋅m Min. 10
at room temperature
Flammability 16 - Min. HB Type A only – Flame
out time not
applicable
Carbon black 17 % Min. 2,5
content
Resistance to 18  Use the fluids and
selected fluids   test temperatures
   specified in Table 2
Tensile strength 10.1 and 10.2 MPa Min. 8
Elongation at break 10.1 and 10.2 % Min. 200
Heat ageing 20  Heat at
150 °C ± 3 K
Tensile strength 10.1 and 10.2 MPa Min. 8
Elongation at break 10.1 and 10.2 % Min. 200
Long term ageing 19  The ageing
   temperature shall be
°
Elongation at break 10.2 % Min. 150 100 C ± 3 K
Hardness ISO 868 Shore D Min. 40
Water absorption 21 % Max. 0.5
Peel adhesion 23 N/25 mm Min. 60 For Type W lined
product only.
Recover at
200 °C ± 5 K for
(10 ± 1) min.
Use compatible
sleeving (Annex A)

---------------------- Page: 10 ----------------------
IEC 62677-3-101:2018 © IEC 2018 – 9 –
Property IEC 62677-2:2017 Units Ma
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.