IEC 61784-5-8:2018
(Main)Industrial communication networks - Profiles - Part 5-8: Installation of fieldbuses - Installation profiles for CPF 8
Industrial communication networks - Profiles - Part 5-8: Installation of fieldbuses - Installation profiles for CPF 8
IEC 61784-5-8:2018 specifies the installation profiles for CPF 8 (CC-Link ).
This deliverable contains a number of related files covering the communication profiles to be used with IEC 61918.
This installation profile documents contained herewith provide the installation profiles of the communication profiles (CP) of a specific communication profile family (CPF) by stating which requirements of IEC 61918 fully apply and, where necessary, by supplementing, modifying, or replacing the other requirements. The installation profiles are specified in the annexes. These annexes are read in conjunction with IEC 61918.
This edition includes the following significant technical changes with respect to the previous edition:
a) The reference to ISO/IEC 24702 has been replaced with reference to the new ISO/IEC 11801-3;
b) Annex C has been extended to cover the balanced cabling based on Ethernet that is applicable to CP8/4. Table C.1, Table C.3, Table C.5 and Table C.8 are added;
c) Annex D has been extended to cover the M12-8 X-coding connector use that is applicable to CP/8/5. Table D.3 is revised.
Réseaux de communication industriels - Profils - Partie 5-8: Installation des bus de terrain - Profils d’installation pour CPF 8
L’IEC 61784-5-8:2018 définit les profils d’installation pour la CPF 8 (CC-Link ).
Les profils d’installation sont spécifiés dans les annexes. Ces annexes sont utilisées conjointement avec l’IEC 61918:2018
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61784-5-8
®
Edition 2.0 2018-08
INTERNATIONAL
STANDARD
colour
inside
Industrial communication networks – Profiles –
Part 5-8: Installation of fieldbuses – Installation profiles for CPF 8
IEC 61784-5-8:2018-08(en)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2018 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
---------------------- Page: 2 ----------------------
IEC 61784-5-8
®
Edition 2.0 2018-08
INTERNATIONAL
STANDARD
colour
inside
Industrial communication networks – Profiles –
Part 5-8: Installation of fieldbuses – Installation profiles for CPF 8
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.040.40; 35.100.40 ISBN 978-2-8322-5941-2
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 3 ----------------------
– 2 – IEC 61784-5-8:2018 © IEC 2018
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms, definitions and abbreviated terms . 9
4 CPF 8: Overview of installation profiles . 9
5 Installation profile conventions . 10
6 Conformance to installation profiles . 10
Annex A (normative) CP 8/1 and CP 8/2 (CC-Link/V1 and CC-Link/V2) specific
installation profile . 12
A.1 Installation profile scope . 12
A.2 Normative references . 12
A.3 Installation profile terms, definitions, and abbreviated terms . 12
A.3.1 Terms and definitions . 12
A.3.2 Abbreviated terms . 12
A.3.3 Conventions for installation profiles . 12
A.4 Installation planning . 12
A.4.1 General . 12
A.4.2 Planning requirements . 13
A.4.3 Network capabilities. 13
A.4.4 Selection and use of cabling components . 15
A.4.5 Cabling planning documentation . 20
A.4.6 Verification of cabling planning specification . 20
A.5 Installation implementation . 20
A.5.1 General requirements . 20
A.5.2 Cable installation . 21
A.5.3 Connector installation . 22
A.5.4 Terminator installation . 22
A.5.5 Device installation . 23
A.5.6 Coding and labelling . 23
A.5.7 Earthing and bonding of equipment and devices and shield cabling . 23
A.5.8 As-implemented cabling documentation . 24
A.6 Installation verification and installation acceptance test . 24
A.6.1 General . 24
A.6.2 Installation verification . 24
A.6.3 Installation acceptance test . 25
A.7 Installation administration . 25
A.8 Installation maintenance and installation troubleshooting . 25
Annex B (normative) CP 8/3 (CC-Link/LT) specific installation profile . 26
B.1 Installation profile scope . 26
B.2 Normative references . 26
B.3 Installation profile terms, definitions, and abbreviated terms . 26
B.3.1 Terms and definitions . 26
B.3.2 Abbreviated terms . 26
B.3.3 Conventions for installation profiles . 26
B.4 Installation planning . 26
---------------------- Page: 4 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 3 –
B.4.1 General . 26
B.4.2 Planning requirements . 27
B.4.3 Network capabilities. 27
B.4.4 Selection and use of cabling components . 30
B.4.5 Cabling planning documentation . 37
B.4.6 Verification of cabling planning specification . 37
B.5 Installation implementation . 37
B.5.1 General requirements . 37
B.5.2 Cable installation . 37
B.5.3 Connector installation . 38
B.5.4 Terminator installation . 39
B.5.5 Device installation . 39
B.5.6 Coding and labelling . 39
B.5.7 Earthing and bonding of equipment and devices and shield cabling . 39
B.5.8 As-implemented cabling documentation . 40
B.6 Installation verification and installation acceptance test . 40
B.6.1 General . 40
B.6.2 Installation verification . 40
B.6.3 Installation acceptance test . 41
B.7 Installation administration . 41
B.8 Installation maintenance and installation troubleshooting . 41
Annex C (normative) CP 8/4 (CC-Link IE Controller Network) specific installation
profile . 42
C.1 Installation profile scope . 42
C.2 Normative references . 42
C.3 Installation profile terms, definitions, and abbreviated terms . 42
C.3.1 Terms and definitions . 42
C.3.2 Abbreviated terms . 42
C.3.3 Conventions for installation profiles . 42
C.4 Installation planning . 42
C.4.1 General . 42
C.4.2 Planning requirements . 42
C.4.3 Network capabilities. 43
C.4.4 Selection and use of cabling components . 45
C.4.5 Cabling planning documentation . 50
C.4.6 Verification of cabling planning specification . 51
C.5 Installation implementation . 51
C.5.1 General requirements . 51
C.5.2 Cable installation . 51
C.5.3 Connector installation . 52
C.5.4 Terminator installation . 53
C.5.5 Device installation . 53
C.5.6 Coding and labelling . 53
C.5.7 Earthing and bonding of equipment and devices and shield cabling . 53
C.5.8 As-implemented cabling documentation . 54
C.6 Installation verification and installation acceptance test . 54
C.6.1 General . 54
C.6.2 Installation verification . 54
C.6.3 Installation acceptance test . 55
---------------------- Page: 5 ----------------------
– 4 – IEC 61784-5-8:2018 © IEC 2018
C.7 Installation administration . 55
C.8 Installation maintenance and installation troubleshooting . 56
Annex D (normative) CP 8/5 (CC-Link IE Field Network) specific installation profile . 57
D.1 Installation profile scope . 57
D.2 Normative references . 57
D.3 Installation profile terms, definitions, and abbreviated terms . 57
D.3.1 Terms and definitions . 57
D.3.2 Abbreviated terms . 57
D.3.3 Conventions for installation profiles . 57
D.4 Installation planning . 57
D.4.1 General . 57
D.4.2 Planning requirements . 57
D.4.3 Network capabilities. 58
D.4.4 Selection and use of cabling components . 59
D.4.5 Cabling planning documentation . 64
D.4.6 Verification of cabling planning specification . 65
D.5 Installation implementation . 65
D.5.1 General requirements . 65
D.5.2 Cable installation . 65
D.5.3 Connector installation . 66
D.5.4 Terminator installation . 66
D.5.5 Device installation . 67
D.5.6 Coding and labelling . 67
D.5.7 Earthing and bonding of equipment and devices and shield cabling . 67
D.5.8 As-implemented cabling documentation . 68
D.6 Installation verification and installation acceptance test . 68
D.6.1 General . 68
D.6.2 Installation verification . 68
D.6.3 Installation acceptance test . 69
D.7 Installation administration . 69
D.8 Installation maintenance and installation troubleshooting . 69
Bibliography . 70
Figure 1 – Standards relationships . 8
Figure A.1 – Pass-through connector configuration . 14
Figure A.2 – Bus t-branch topology . 14
Figure A.3 – Wiring . 17
Figure B.1 – Powered network topology . 28
Figure B.2 – Bus t-branch topology . 28
Figure B.3 – Flat cable cross section – with key . 31
Figure B.4 – Flat cable cross section – without key . 31
Figure B.5 – Flat cable polarity marking . 31
Figure B.6 – Wiring . 32
Figure B.7 – Flat cable connector and terminal cover . 33
Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet . 15
Table A.2 – Bus t-branch network characteristics . 15
---------------------- Page: 6 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 5 –
Table A.3 – Information relevant to copper cable: fixed cables . 16
Table A.4 – Connectors for copper cabling CPs not based on Ethernet . 17
Table A.5 – Parameters for balanced cables . 21
Table A.6 – Cable conductor assignments . 22
Table B.1 – Basic network characteristics for balanced cabling not based on Ethernet . 29
Table B.2 – CP 8/3 additional topology length limits . 29
Table B.3 – Information relevant to copper cable: cords . 31
Table B.4 – Connectors for copper cabling CPs not based on Ethernet . 34
Table B.5 – Parameters for balanced cables . 37
Table B.6 – Flat cable conductor assignments . 38
Table C.1 – Network characteristics for balanced cabling based on Ethernet . 44
Table C.2 – Network characteristics for optical fibre cabling . 44
Table C.3 – Information relevant to copper cable: fixed cables. 45
Table C.4 – Information relevant to optical fibre cables . 46
Table C.5– Connectors for balanced cabling CPs based on Ethernet . 46
Table C.6 – Optical fibre connecting hardware . 47
Table C.7 – Relationship between FOC and fibre types (CP 8/4) . 47
Table C.8 – Parameters for balanced cables . 51
Table C.9 – Parameters for silica optical fibre cables . 51
Table D.1 – Network characteristics for balanced cabling based on Ethernet . 59
Table D.2 – Information relevant to copper cable: fixed cables. 60
Table D.3 – Connectors for balanced cabling CPs based on Ethernet . 61
Table D.4 – Parameters for balanced cables . 65
---------------------- Page: 7 ----------------------
– 6 – IEC 61784-5-8:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-8: Installation of fieldbuses –
Installation profiles for CPF 8
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-8 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This second edition cancels and replaces the first edition published in 2013. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) The reference to ISO/IEC 24702 has been replaced with reference to the new
ISO/IEC 11801-3;
b) Annex C has been extended to cover the balanced cabling based on Ethernet that is
applicable to CP8/4. Table C.1, Table C.3, Table C.5 and Table C.8 are added;
---------------------- Page: 8 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 7 –
c) Annex D has been extended to cover the M12-8 X-coding connector use that is applicable
to CP/8/5. Table D.3 is revised.
This standard is to be used in conjunction with IEC 61918:2018.
The text of this International Standard is based on the following documents:
FDIS Report on voting
65C/924/FDIS 65C/925/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 61784-5 series, under the general title Industrial communication
networks – Profiles – Installation of fieldbuses, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related
to the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 9 ----------------------
– 8 – IEC 61784-5-8:2018 © IEC 2018
INTRODUCTION
This International Standard is one of a series produced to facilitate the use of communication
networks in industrial control systems.
IEC 61918:2018 provides the common requirements for the installation of communication
networks in industrial control systems. This installation profile standard provides the
installation profiles of the communication profiles (CP) of a specific communication profile
family (CPF) by stating which requirements of IEC 61918:2018 fully apply and, where
necessary, by supplementing, modifying, or replacing the other requirements (see Figure 1).
For general background on fieldbuses, their profiles, and relationship between the installation
profiles specified in this document, see IEC 61158-1.
Each CP installation profile is specified in a separate annex of this document. Each annex is
structured exactly as the reference standard IEC 61918:2018 for the benefit of the persons
representing the roles in the fieldbus installation process as defined in IEC 61918:2018
(planner, installer, verification personnel, validation personnel, maintenance personnel,
administration personnel). By reading the installation profile in conjunction with IEC
61918:2018, these persons immediately k
...
IEC 61784-5-8
®
Edition 2.0 2018-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Industrial communication networks – Profiles –
Part 5-8: Installation of fieldbuses – Installation profiles for CPF 8
Réseaux de communication industriels – Profils –
Partie 5-8: Installation des bus de terrain – Profils d’installation pour CPF 8
IEC 61784-5-8:2018-08(en-fr)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2018 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - Electropedia - www.electropedia.org
webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.
IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary
Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et Définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues depuis 2002. Plus certaines entrées
antérieures extraites des publications des CE 37, 77, 86 et
Service Clients - webstore.iec.ch/csc CISPR de l'IEC.
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
---------------------- Page: 2 ----------------------
IEC 61784-5-8
®
Edition 2.0 2018-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Industrial communication networks – Profiles –
Part 5-8: Installation of fieldbuses – Installation profiles for CPF 8
Réseaux de communication industriels – Profils –
Partie 5-8: Installation des bus de terrain – Profils d’installation pour CPF 8
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40; 35.100.40 ISBN 978-2-8322-9180-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – IEC 61784-5-8:2018 © IEC 2018
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms, definitions and abbreviated terms . 9
4 CPF 8: Overview of installation profiles . 9
5 Installation profile conventions . 10
6 Conformance to installation profiles . 10
Annex A (normative) CP 8/1 and CP 8/2 (CC-Link/V1 and CC-Link/V2) specific
installation profile . 12
A.1 Installation profile scope . 12
A.2 Normative references . 12
A.3 Installation profile terms, definitions, and abbreviated terms . 12
A.3.1 Terms and definitions . 12
A.3.2 Abbreviated terms . 12
A.3.3 Conventions for installation profiles . 12
A.4 Installation planning . 12
A.4.1 General . 12
A.4.2 Planning requirements . 13
A.4.3 Network capabilities. 13
A.4.4 Selection and use of cabling components . 15
A.4.5 Cabling planning documentation . 20
A.4.6 Verification of cabling planning specification . 20
A.5 Installation implementation . 20
A.5.1 General requirements . 20
A.5.2 Cable installation . 21
A.5.3 Connector installation . 22
A.5.4 Terminator installation . 22
A.5.5 Device installation . 23
A.5.6 Coding and labelling . 23
A.5.7 Earthing and bonding of equipment and devices and shield cabling . 23
A.5.8 As-implemented cabling documentation . 24
A.6 Installation verification and installation acceptance test . 24
A.6.1 General . 24
A.6.2 Installation verification . 24
A.6.3 Installation acceptance test . 25
A.7 Installation administration . 25
A.8 Installation maintenance and installation troubleshooting . 25
Annex B (normative) CP 8/3 (CC-Link/LT) specific installation profile . 26
B.1 Installation profile scope . 26
B.2 Normative references . 26
B.3 Installation profile terms, definitions, and abbreviated terms . 26
B.3.1 Terms and definitions . 26
B.3.2 Abbreviated terms . 26
B.3.3 Conventions for installation profiles . 26
B.4 Installation planning . 26
---------------------- Page: 4 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 3 –
B.4.1 General . 26
B.4.2 Planning requirements . 27
B.4.3 Network capabilities. 27
B.4.4 Selection and use of cabling components . 30
B.4.5 Cabling planning documentation . 37
B.4.6 Verification of cabling planning specification . 37
B.5 Installation implementation . 37
B.5.1 General requirements . 37
B.5.2 Cable installation . 37
B.5.3 Connector installation . 38
B.5.4 Terminator installation . 39
B.5.5 Device installation . 39
B.5.6 Coding and labelling . 39
B.5.7 Earthing and bonding of equipment and devices and shield cabling . 39
B.5.8 As-implemented cabling documentation . 40
B.6 Installation verification and installation acceptance test . 40
B.6.1 General . 40
B.6.2 Installation verification . 40
B.6.3 Installation acceptance test . 41
B.7 Installation administration . 41
B.8 Installation maintenance and installation troubleshooting . 41
Annex C (normative) CP 8/4 (CC-Link IE Controller Network) specific installation
profile . 42
C.1 Installation profile scope . 42
C.2 Normative references . 42
C.3 Installation profile terms, definitions, and abbreviated terms . 42
C.3.1 Terms and definitions . 42
C.3.2 Abbreviated terms . 42
C.3.3 Conventions for installation profiles . 42
C.4 Installation planning . 42
C.4.1 General . 42
C.4.2 Planning requirements . 42
C.4.3 Network capabilities. 43
C.4.4 Selection and use of cabling components . 45
C.4.5 Cabling planning documentation . 50
C.4.6 Verification of cabling planning specification . 50
C.5 Installation implementation . 51
C.5.1 General requirements . 51
C.5.2 Cable installation . 51
C.5.3 Connector installation . 52
C.5.4 Terminator installation . 53
C.5.5 Device installation . 53
C.5.6 Coding and labelling . 53
C.5.7 Earthing and bonding of equipment and devices and shield cabling . 53
C.5.8 As-implemented cabling documentation . 54
C.6 Installation verification and installation acceptance test . 54
C.6.1 General . 54
C.6.2 Installation verification . 54
C.6.3 Installation acceptance test . 55
---------------------- Page: 5 ----------------------
– 4 – IEC 61784-5-8:2018 © IEC 2018
C.7 Installation administration . 55
C.8 Installation maintenance and installation troubleshooting . 55
Annex D (normative) CP 8/5 (CC-Link IE Field Network) specific installation profile . 56
D.1 Installation profile scope . 56
D.2 Normative references . 56
D.3 Installation profile terms, definitions, and abbreviated terms . 56
D.3.1 Terms and definitions . 56
D.3.2 Abbreviated terms . 56
D.3.3 Conventions for installation profiles . 56
D.4 Installation planning . 56
D.4.1 General . 56
D.4.2 Planning requirements . 56
D.4.3 Network capabilities. 57
D.4.4 Selection and use of cabling components . 58
D.4.5 Cabling planning documentation . 63
D.4.6 Verification of cabling planning specification . 63
D.5 Installation implementation . 63
D.5.1 General requirements . 63
D.5.2 Cable installation . 64
D.5.3 Connector installation . 65
D.5.4 Terminator installation . 65
D.5.5 Device installation . 65
D.5.6 Coding and labelling . 65
D.5.7 Earthing and bonding of equipment and devices and shield cabling . 66
D.5.8 As-implemented cabling documentation . 67
D.6 Installation verification and installation acceptance test . 67
D.6.1 General . 67
D.6.2 Installation verification . 67
D.6.3 Installation acceptance test . 68
D.7 Installation administration . 68
D.8 Installation maintenance and installation troubleshooting . 68
Bibliography . 69
Figure 1 – Standards relationships . 8
Figure A.1 – Pass-through connector configuration . 14
Figure A.2 – Bus t-branch topology . 14
Figure A.3 – Wiring . 17
Figure B.1 – Powered network topology . 28
Figure B.2 – Bus t-branch topology . 28
Figure B.3 – Flat cable cross section – with key . 31
Figure B.4 – Flat cable cross section – without key . 31
Figure B.5 – Flat cable polarity marking . 31
Figure B.6 – Wiring . 32
Figure B.7 – Flat cable connector and terminal cover . 33
Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet . 15
Table A.2 – Bus t-branch network characteristics . 15
---------------------- Page: 6 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 5 –
Table A.3 – Information relevant to copper cable: fixed cables . 16
Table A.4 – Connectors for copper cabling CPs not based on Ethernet . 17
Table A.5 – Parameters for balanced cables . 21
Table A.6 – Cable conductor assignments . 22
Table B.1 – Basic network characteristics for balanced cabling not based on Ethernet . 29
Table B.2 – CP 8/3 additional topology length limits . 29
Table B.3 – Information relevant to copper cable: cords . 31
Table B.4 – Connectors for copper cabling CPs not based on Ethernet . 34
Table B.5 – Parameters for balanced cables . 37
Table B.6 – Flat cable conductor assignments . 38
Table C.1 – Network characteristics for balanced cabling based on Ethernet . 44
Table C.2 – Network characteristics for optical fibre cabling . 44
Table C.3 – Information relevant to copper cable: fixed cables. 45
Table C.4 – Information relevant to optical fibre cables . 46
Table C.5 – Connectors for balanced cabling CPs based on Ethernet . 46
Table C.6 – Optical fibre connecting hardware . 47
Table C.7 – Relationship between FOC and fibre types (CP 8/4) . 47
Table C.8 – Parameters for balanced cables . 51
Table C.9 – Parameters for silica optical fibre cables . 51
Table D.1 – Network characteristics for balanced cabling based on Ethernet . 58
Table D.2 – Information relevant to copper cable: fixed cables. 59
Table D.3 – Connectors for balanced cabling CPs based on Ethernet . 60
Table D.4 – Parameters for balanced cables . 64
---------------------- Page: 7 ----------------------
– 6 – IEC 61784-5-8:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-8: Installation of fieldbuses –
Installation profiles for CPF 8
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-8 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This second edition cancels and replaces the first edition published in 2013. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) The reference to ISO/IEC 24702 has been replaced with reference to the new
ISO/IEC 11801-3;
b) Annex C has been extended to cover the balanced cabling based on Ethernet that is
applicable to CP8/4. Table C.1, Table C.3, Table C.5 and Table C.8 are added;
---------------------- Page: 8 ----------------------
IEC 61784-5-8:2018 © IEC 2018 – 7 –
c) Annex D has been extended to cover the M12-8 X-coding connector use that is applicable
to CP/8/5. Table D.3 is revised.
This standar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.