IEC GUIDE 109:2012
(Main)Environmental aspects - Inclusion in electrotechnical product standards
Environmental aspects - Inclusion in electrotechnical product standards
IEC Guide 109:2012 is intended for standards writers and gives guidance on how to consider aspects relating to the impact on the environment of electrotechnical products when preparing standards for such products.
Aspects liés à l'environnement - Prise en compte dans les normes électrotechniques de produits
Le IEC Guide 109:2012 est destiné aux rédacteurs de normes et fournit des lignes directrices sur la manière d'appréhender, lors de l'élaboration de normes pour des produits de ce type, les aspects liés à l'impact des produits électrotechniques sur l'environnement.
General Information
Relations
Standards Content (Sample)
IEC GUIDE 109 ®
Edition 3.0 2012-06
GUIDE
GUIDE
Environmental aspects – Inclusion in electrotechnical product standards
Aspects liés à l'environnement – Prise en compte dans les normes
électrotechniques de produits
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC GUIDE 109 ®
Edition 3.0 2012-06
GUIDE
GUIDE
Environmental aspects – Inclusion in electrotechnical product standards
Aspects liés à l'environnement – Prise en compte dans les normes
électrotechniques de produits
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 13.020 ISBN 978-2-83220-141-1
– 2 – Guide 109 IEC:2012
CONTENTS
INTRODUCTION . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Product standards and the environment . 9
4.1 General . 9
4.2 Influence of provisions in product standards on the environment . 10
4.3 Environmental strategies . 12
5 Inputs and outputs to be considered in the development of product standards . 13
5.1 General . 13
5.2 Inputs . 14
5.3 Outputs . 14
Annex A Checklist for the consideration of environmental aspects in product standards. 15
Bibliography . 16
Figure 1 – Relationship between provisions in product standards and the
environmental aspects and impacts associated with the product during its life cycle . 11
Guide 109 IEC:2012 – 3 –
ENVIRONMENTAL ASPECTS –
INCLUSION IN ELECTROTECHNICAL PRODUCT STANDARDS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This third edition of IEC Guide 109 has been prepared, in accordance with ISO/IEC
Directives, Part 1, Annex A, by the IEC Advisory Committee on Environmental Aspects
(ACEA). This guide is a non-mandatory guide in accordance with SMB Decision 136/8.
This third edition cancels and replaces the second edition edition published in 2003.
The main changes with respect to the previous edition are as follows. This new edition:
− is aligned to the revised ISO Guide 64 as far as it is relevant for standard writers;
− emphasizes life cycle thinking as described in the horizontal standard IEC 62430;
− provides a more elaborated check list in the annex.
– 4 – Guide 109 IEC:2012
The text of this IEC Guide is based on the following documents:
Four month’s vote Report on voting
C/1715/DV C/1730/RV
Full information on the voting for the approval of this Guide can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
Guide 109 IEC:2012 – 5 –
INTRODUCTION
This Guide aims to give advice to standards writers on the way environment aspects should
be considered and taken into account as applicable during the development of standards.
Finding an appropriate solution for the product is the task of product designers; this solution
will be a trade-off along various dimensions (safety, environment, cost, technology, function
and so on). This Guide is intended for standards writers and not for product designers; it aims
at encouraging standards that preserve the natural environment while allowing designers to
reach the best practical compromise among the constraints.
1)
The need to reduce the adverse impacts on the natural environment based on a product’s
aspects during all stages of its life – from acquiring materials to manufacturing, distribution,
use, and end-of-life treatment (i.e. re-use, recycling) – is recognized in most countries around
the world. One achieves reduction of adverse environmental impacts by improving a product’s
environmental aspects. The choices made at the design stage largely determine what those
impacts will be during each stage of the life of that product. There are, however, considerable
obstacles that make the task of selecting the best environmental options very complex. For
example, selecting design options to improve environmental aspects can involve difficult
trade-offs, such as that a more energy efficient design causes the product to become less
recyclable.
Requirements for products may influence significantly the extent of environmental impacts.
Standards should promote flexibility in the selection of design options in order to improve
environmental aspects. Furthermore, standards must not prohibit innovation in any sense.
Standards writers should encourage the protection of the environment, for instance, by
specifying requirements that do not rule out the appropriate use of recycled material and the
re-use of components, subsystems and systems.
The continual introduction of new products and materials can make evaluation increasingly
complex, since additional data must be gathered to assess the life cycle impacts and aspects
of such new products and materials. Moreover, there is currently very little data available on
the environmental impacts of some materials. However, the data which exists can be used as
a basis for improvement of the products with respect to environmental aspects.
IEC 62430 specifies principles of life cycle thinking (LCT) with its essential steps as well as
2)
tools such as life cycle
various general environmentally conscious design (ECD)
assessment (LCA).
IEC 62430 gives all those involved information on how to integrate ECD principles into
product design and development. Standards writers are not expected to perform life cycle
assessment (LCA) but to facilitate ECD as far as possible.
Until more data are available, manufacturers can doc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.