IEC 60364-5-53:2001/AMD2:2015

Amendment 2 - Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control

Amendement 2 - Installations électriques des bâtiments - Partie 5-53: choix et mise en oeuvre des matériels électriques - Sectionnement, coupure et commande

General Information

• Status: Published
• Publication Date: 22-Sep-2015
• ICS: 29.130.01 - Switchgear and controlgear in general
• ICS: 91.140.50 - Electricity supply systems
• Technical Committee: TC 64 - Electrical installations and protection against electric shock
• Drafting Committee: MT 3 - TC 64/MT 3
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 21-Feb-2019

Relations

• Amends: IEC 60364-5-53:2001 - Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
• Effective Date: 05-Sep-2023
• Revised: IEC 60364-5-53:2019 - Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Devices for protection for safety, isolation, switching, control and monitoring
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60364-5-53 ®
Edition 3.0 2015-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
A MENDMENT 2
AM ENDEMENT 2
Electrical installations of buildings –
Part 5-53: Selection and erection of electrical equipment – Isolation, switching
and control
Installations électriques des bâtiments –
Partie 5-53: Choix et mise en oeuvre des matériels électriques – Sectionnement,
coupure et commande
IEC 60364-5-53:2001-08/AMD2:2015-09(en-fr)

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie

et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des

questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]
CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 15
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 60 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,

77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient plus de 30 000 termes et définitions en
Spécifications techniques, Rapports techniques et autres
anglais et en français, ainsi que les termes équivalents dans
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
15 langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.

Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
Plus de 60 000 entrées terminologiques électrotechniques, en
La recherche avancée permet de trouver des publications IEC
en utilisant différents critères (numéro de référence, texte, anglais et en français, extraites des articles Termes et
comité d’études,…). Elle donne aussi des informations sur les Définitions des publications IEC parues depuis 2002. Plus
projets et les publications remplacées ou retirées. certaines entrées antérieures extraites des publications des

CE 37, 77, 86 et CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished

Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
[e-mail].
IEC 60364-5-53 ®
Edition 3.0 2015-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
A MENDMENT 2
AM ENDEMENT 2
Electrical installations of buildings –

Part 5-53: Selection and erection of electrical equipment – Isolation, switching

and control
Installations électriques des bâtiments –

Partie 5-53: Choix et mise en oeuvre des matériels électriques – Sectionnement,

coupure et commande
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.130; 91.140.50 ISBN 978-2-8322-2883-8

– 2 – IEC 60364-5-53:2001/AMD2:2015

© IEC 2015
FOREWORD
This amendment has been prepared by IEC technical committee 64: Electrical installations

and protection against electric shock.

The text of this amendment is based on the following documents:

FDIS Report on voting
64/2031/FDIS 64/2072/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it
contains colours which are considered to be useful for the correct understanding of its contents.
Users should therefore print this document using a colour printer.

_______
FOREWORD
Replace the existing text, including the text provided in Amendment 1:2002 that reads:
"This publication has been drafted, as close as possible, in accordance with the ISO/IEC

Directives, Part 3"
by the following new sentence:
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
Delete, from both IEC 60364-5-53:2001 and from Amendment 1:2002, the sentence that reads
"Annexes A, B, C and D are for information only."

530.2 Normative references
Add the following new references:
IEC 60038, IEC standard voltages
IEC 60364-5-54, Low-voltage electrical installations – Part 5-54: Selection and erection of
electrical equipment – Earthing arrangements and protective conductors

© IEC 2015
IEC 61643-11:2011, Low-voltage surge protective devices – Part 11: Surge protective devices

connected to low-voltage power systems – Requirements and test methods

IEC 62305 (all parts), Protection against lightning

IEC 62305-1, Protection against lightning – Part 1: General principles

IEC 62305-2, Protection against lightning – Part 2: Risk management

IEC 62305-4, Protection against lightning – Part 4: Electrical and electronic systems within

structures
Replace the current reference to "IEC 61643-12" by the following:
IEC 61643-12:2008, Low-voltage surge protective devices – Part 12: Surge protective devices
connected to low-voltage power distribution systems – Selection and application principles
Replace the existing date "2001" for IEC 60364-4-41 by "2005"
Replace the existing date "2001" for IEC 60364-4-43 by "2008"
Replace the existing date "2001" for IEC 60364-4-44 by "2007"
Replace the existing date "1996" for IEC 61008-1 by "2010"

534 Devices for protection against electromagnetic and voltage disturbances
Replace the existing title and text of Clause 534, including the text provided in Amendment
1:2002, by the following new title and text:
534 Devices for protection against transient overvoltages
534.1 General
This clause contains provisions for the application of voltage limitation in order to obtain
insulation coordination in the cases described in IEC 60364-4-44, IEC 60664-1, IEC 62305-1,
IEC 62305-4 and IEC 61643-12.
This clause focuses mainly on the requirements for the selection and erection of SPDs for
protection against transient overvoltages where required by Clause 443 of IEC 60364-4-
44:2007, the IEC 62305 series, or as otherwise specified.
This clause does not take into account:

– surge protective components which may be incorporated in the appliances connected to
the installation;
– portable SPDs.
NOTE Further information can be found in IEC 61643-12.
This clause applies to a.c. power circuits. As far as it is applicable, the requirements of this
clause may be followed for d.c. power circuits.
534.2 Void
534.3 Terms and definitions
534.3.1
SPD assembly
one SPD or a set of SPDs, in both cases including all SPD disconnectors required by the SPD
manufacturer, providing the required overvoltage protection for a type of system earthing

– 4 – IEC 60364-5-53:2001/AMD2:2015

© IEC 2015
534.3.2
SPD disconnector
disconnector
device for disconnecting an SPD, or part of an SPD, from the power system

Note 1 to entry: This disconnecting device is not required to have isolating capability for safety purposes. It is to

prevent a persistent fault on the system and is used to give an indication of an SPD’s failure. Disconnectors can be

internal (built in) or external (required by the manufacturer). There may be more than one disconnector function, for
example an over-current protection function and a thermal protection function. These functions may be in separate
units.
[SOURCE: IEC 61643-11:2011, 3.1.28]

534.3.3
mode of protection of an SPD
intended current path, between terminals that contains protective components, e.g. line-to-
line, line-to-earth, line-to-neutral, neutral-to-earth
[SOURCE: IEC 61643-11:2011, 3.1.8]
534.3.4
follow current interrupt rating
I
fi
prospective short-circuit current that an SPD is able to interrupt without operation of a
disconnector
[SOURCE: IEC 61643-11:2011, 3.1.39]
534.3.5
short-circuit current rating
I
SCCR
maximum prospective short-circuit current from the power system for which the SPD, in
conjunction with the disconnector specified, is rated
[SOURCE: IEC 61643-11:2011, 3.1.27]
534.3.6
voltage protection level
U
P
maximum voltage to be expected at the SPD terminals due to an impulse stress with defined
voltage steepness and an impulse stress with a discharge current with given amplitude and
waveshape
Note 1 to entry: The voltage protection level is given by the manufacturer and may not be exceeded by:
– the measured limiting voltage determined for front-of-wave sparkover (if applicable) and the measured limiting
voltage determined from the residual voltage measurements at amplitudes corresponding to I and/or I
n imp
respectively for test classes II and/or I;
– the measured limiting voltage at the open circuit voltage of the combination wave generator (U ), determined
OC
for the combination wave for test class III.
[SOURCE: IEC 61643-11:2011, 3.1.14]
534.3.7
rated impulse voltage
U
W
impulse withstand voltage value assigned by the manufacturer to the equipment or to a part of
it, characterizing the specified withstand capability of its insulation against transient
overvoltages
[SOURCE: IEC 60664-1:2007, 3.9.2 MOD]

© IEC 2015
534.3.8
maximum continuous operating voltage

U
C
maximum r.m.s. voltage, which may be continuously applied to the SPD's mode of protection

Note 1 to entry: The U value covered by this standard may exceed 1 000 V.
C
[SOURCE: IEC 61643-11:2011, 3.1.11]

534.3.9
nominal discharge current for class II test

I
n
crest value of the current through the SPD having a current waveshape of 8/20
[SOURCE: IEC 61643-11:2011, 3.1.9]
534.3.10
impulse discharge current for class I test
I
imp
crest value of a discharge current through the SPD with specified charge transfer Q and
specified energy W/R in the specified time
[SOURCE: IEC 61643-11:2011, 3.1.10]
534.3.11
two-port SPD
SPD having specific series impedance connected between separate input and output
connections
[SOURCE: IEC 61643-11:2011, 3.1.3]
534.4 Selection and erection of SPDs
534.4.1 SPD location and SPD test class
SPDs shall at least be instal
...