IEC TR 62343-6-2:2009

Dynamic modules - Part 6-2: Software and hardware interfaces - Survey results

IEC/TR 62343-6-2:2009(E) clarifies dynamic module interfaces which should be standardized based on a survey of manufacturers. The objectives of this technical report are to present the survey results and to propose software (SW) and hardware (HW) interface standards of dynamic modules.

General Information

• Status: Published
• Publication Date: 13-Jul-2009
• ICS: 33.180.01 - Fibre optic systems in general
• ICS: 43.060.50 - Electrical and electronic equipment. Control systems
• Technical Committee: SC 86C - Fibre optic systems and active devices
• Drafting Committee: WG 5 - TC 86/SC 86C/WG 5
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 06-Aug-2013

Relations

• Revised: IEC TR 62343-6-2:2013 - Dynamic modules - Part 6-2: Design guide - Software and hardware interfaces - Survey results
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC/TR 62343-6-2
®
Edition 1.0 2009-07
TECHNICAL
REPORT

Dynamic modules –
Part 6-2: Software and hardware interfaces – Survey results


IEC/TR 62343-6-2:2009(E)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2009 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC/TR 62343-6-2
®
Edition 1.0 2009-07
TECHNICAL
REPORT

Dynamic modules –
Part 6-2: Software and hardware interfaces – Survey results


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 33.180; 43.060.50 ISBN 978-2-88910-680-6
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 3 ----------------------
– 2 – TR 62343-6-2 © IEC:2009(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Survey description.5
2.1 Survey contents .5
2.2 Survey conditions.5
3 Interface definitions .5
3.1 General .5
3.2 Interface A .6
3.3 Interface B .6
3.4 Interface C .6
3.5 Other interfaces .6
4 Survey results .7
4.1 Types of dynamic modules .7
4.2 Standards of the control interface dealt in the past (from suppliers).7
4.3 Potential future control interface standards (from suppliers). .8
4.4 Standards of the control interface requested (from users) .9
4.5 Comments about the standards of a typical control interface (from suppliers
and users) .9
4.6 Opinions about standardization of control interfaces (from suppliers and
users).9
5 Priority for standardization.9
6 Conclusion .10
Annex A (informative) A summary of responses from each surveyed region.11

Figure 1 – Layer structure of dynamic module interface .6
Figure 2 – Features of the interfaces .10

Table 1 – Types of dynamic modules .7
Table 2 – Standards of the control interface dealt in the past.8
Table 3 – Standards of the control interface planned to be offered in the future .8
Table 4 – Requested standards of the control interface (from users).9
Table 5 – Priority to standardize .10

---------------------- Page: 4 ----------------------
TR 62343-6-2 © IEC:2009(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

DYNAMIC MODULES –

Part 6-2: Software and hardware
interfaces – Survey results


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC 62343-6-2, which is a technical report, has been prepared by subcommittee 86C: Fibre
optic systems and active devices, of IEC technical committee 86: Fibre optics.
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
86C/880/DTR 86C/893/RVC

Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.

---------------------- Page: 5 ----------------------
– 4 – TR 62343-6-2 © IEC:2009(E)
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 62343 series, published under the general title Dynamic modules, can
be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

---------------------- Page: 6 ----------------------
TR 62343-6-2 © IEC:2009(E) – 5 –
DYNAMIC MODULES –

Part 6-2: Software and hardware
interfaces – Survey results



1 Scope
This part of IEC 62343 clarifies dynamic module interfaces which should be standardized
based on a survey of manufacturers. The objectives of this technical report are to present the
survey results and to propose software (SW) and hardware (HW) interface standards of
dynamic modules.
2 Survey descr
...