IEC 61935-2-25:2015

Generic cabling systems - Specification for the testing of balanced communication cabling in accordance with ISO/IEC 11801 - Part 2-25: Work area cord with M12 4 poles connectors - Blank detail specification

IEC 61935-2-25:2015(E) which is a blank detail specification, describes work area cord with M12 4 poles d-code connectors, as used in the ISO/IEC 24702 and IEC 61918. According to the above cabling specifications, although these cords have only two pairs, their transmission performances, when applicable, are at least category 5 compliant for which the requirements are given in ISO/IEC 11801:2002/AMD2:2010, Clause 13. This specification should be used in conjunction with IEC 61156-1, IEC 61156-6 and IEC 61076-2-101 type D. The blank detail specification determines the layout and style for detail specifications describing cords with transmission characteristics up to 100 MHz for digital communications. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer, or a user.
This publication is to be read in conjunction with IEC 61156-1:2007, IEC 61156-6:2010 and IEC 61076-2-101:2012.

General Information

• Status: Published
• Publication Date: 28-Apr-2015
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: TC 46 - Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories
• Drafting Committee: WG 9 - TC 46/WG 9
• Current Stage: PPUB - Publication issued
• Start Date: 31-Jul-2015
• Completion Date: 29-Apr-2015

Standards Content (Sample)

IEC 61935-2-25 ®
Edition 1.0 2015-04
INTERNATIONAL
STANDARD
colour
inside
Generic cabling systems – Specification for the testing of balanced
communication cabling in accordance with ISO/IEC 11801 –
Part 2-25: Work area with M12 4 poles connectors – Blank detail specification
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]
CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 15
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 60 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,

77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC 61935-2-25 ®
Edition 1.0 2015-04
INTERNATIONAL
STANDARD
colour
inside
Generic cabling systems – Specification for the testing of balanced

communication cabling in accordance with ISO/IEC 11801 –

Part 2-25: Work area with M12 4 poles connectors – Blank detail specification

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-2652-0

– 2 – IEC 61935-2-25:2015 © IEC 2015
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Guidance for preparation of detail specifications . 6
4 Blank detail specification for cords for applications up to 100 MHz . 7

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
GENERIC CABLING SYSTEMS – SPECIFICATION FOR
THE TESTING OF BALANCED COMMUNICATION
CABLING IN ACCORDANCE WITH ISO/IEC 11801 –

Part 2-25: Work area with M12 4 poles connectors –
Blank detail specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61935-2-25 has been prepared by IEC technical committee 46:
Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and
accessories.
The text of this standard is based on the following documents:
CDV Report on voting
46/518/CDV 46/544/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC 61935-2-25:2015 © IEC 2015
A list of all parts in the IEC 61935 series, published under the general title Generic cabling
systems – Specification for the testing of balanced communication cabling in accordance with
ISO/IEC 11801, can be found on the IEC website.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
GENERIC CABLING SYSTEMS – SPECIFICATION FOR
THE TESTING OF BALANCED COMMUNICATION
CABLING IN ACCORDANCE WITH ISO/IEC 11801 –

Part 2-25: Work area with M12 4 poles connectors –
Blank detail specification
1 Scope
This part of IEC 61935, which is a blank detail specification, describes work area cord with
M12 4 poles d-code connectors, as used in the ISO/IEC 24702 and IEC 61918.
According to the above cabling specifications, although these cords have only two pairs, their
transmission performances, when applicable, are at least category 5 compliant for which the
requirements are given in ISO/IEC 11801:2002/AMD2:2010, Clause 13.
T
...