IEC 60384-13-1:2006

Fixed capacitors for use in electronic equipment - Part 13-1: Blank detail specification - Fixed polypropylene film dielectric metal foil d.c. capacitors - Assessment level E and EZ

IEC 60384-13-1:2006(E) is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. The contents of the corrigendum of March 2009 have been included in this copy.

General Information

• Status: Published
• Publication Date: 18-Jan-2006
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 31.060.30 - Paper and plastics capacitors
• Technical Committee: TC 40 - Capacitors and resistors for electronic equipment
• Current Stage: PPUB - Publication issued
• Start Date: 15-Apr-2006
• Completion Date: 19-Jan-2006

Relations

• Corrected By: IEC 60384-13-1:2006/COR1:2009 - Corrigendum 1 - Fixed capacitors for use in electronic equipment - Part 13-1: Blank detail specification - Fixed polypropylene film dielectric metal foil d.c. capacitors - Assessment level E
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60384-13-1 ®
Edition 2.0 2006-01
INTERNATIONAL
STANDARD
QC 301801
Fixed capacitors for use in electronic equipment –
Part 13-1: Blank detail specification – Fixed polypropylene film dielectric metal
foil d.c. capacitors – Assessment level E and EZ

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
IEC 60384-13-1 ®
Edition 2.0 2006-01
INTERNATIONAL
STANDARD
QC 301801
Fixed capacitors for use in electronic equipment –
Part 13-1: Blank detail specification – Fixed polypropylene film dielectric metal
foil d.c. capacitors – Assessment level E and EZ

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 31.060.30 ISBN 2-8318-8412-8
– 2 – 60384-13-1 © IEC:2006(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 13-1: Blank detail specification – Fixed polypropylene film
dielectric metal foil d.c. capacitors – Assessment level E and EZ

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-13-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1991 and constitutes a
minor revisions related to tables, figures and references.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1621/FDIS 40/1644/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

60384-13-1  IEC:2006(E) – 3 –
The QC number that appears on the front cover of this publication is the specification number
in the IEC Quality Assessment System for Electronic Components (IECQ).
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in
electronic equipment:
Part 1: Generic specification
Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
d.c. capacitors
Part 3: Sectional specification: Fixed tantalum chip capacitors
Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid
electrolyte
Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage
not exceeding 3000 V – Selection of methods of test and general requirements
Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c.
capacitors
Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1
Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil
d.c. capacitors
Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c.
capacitors
Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c.
capacitors
Part 14: Sectional specification: Fixed capacitors for electromagnetic interference
suppression and connection to the supply mains
Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid
electrolyte
Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c.
capacitors
Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and
pulse capacitors
Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid
electrolyte
Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
chip d.c. capacitors
Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip
d.c. capacitors
Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 1
Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 2
Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate
film dielectric d.c. capacitors

– 4 – 60384-13-1 © IEC:2006(E)
Part 24: Sectional specification – Surface mount fixed tantalum electrolytic capacitors with
conductive polymer solid electrolyte
Part 25: Sectional specification – Surface mount fixed aluminium electrolytic capacitors
with conductive polymer solid electrolyte
All sectional specifications mentioned above do have one or more blank detail specifications
being a supplementary document, containing requirements for style, layout and minimum
content of detail specifications.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
The contents of the corrigendum of March 2009 have been included in this copy.

———————
To be published.
60384-13-1 © IEC:2006(E) – 5 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 13-1: Blank detail specification – Fixed polypropylene film
dielectric metal foil d.c. capacitors – Assessment level E and EZ

Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications the content of 1.4 of the sectional specification shall
be taken into account. The numbers between brackets on the first page correspond to the
following information which shall be inserted in the position indicated.
Identification of the detail specification
(1) The "International Electrotechnical Commission" or the National Standards Organization
under whose authority the detail specification is drafted.
(2) The IEC or National Standards number of the detail specification, date of issue and any
further information required by the national system.
(3) The number and issue number of the IEC or national generic specification.
(4) The IEC number of the blank detail specification.
Identification of the capacitor
(5) A short description of the type of capacitor.
(6) Information on typical construction (when applicable).
When the capacitor is not designed for use in printed-board applications, this shall be
clearly stated in the detail specification in this position.
(7) Outline drawing with main dimensions which are of importance for interchangeability
and/or reference to the national or international documents for outlines. Alternatively,
this drawing may be given in an annex to the detail specification.
(8) Application or group of applications covered and/or assessment level.
The assessment level(s) to be used in a detail specification shall be selected from the
sectional specification, 3.5.4. This implies that one blank detail specification may be
used in combination with several assessment levels, provided the grouping of the tests
does not change.
(9) Reference data on the most important properties, to allow comparison between the
various capacitor types.
– 6 – 60384-13-1  IEC:2006(E)

IEC 60384-13-1-XXX
(2)
QC 301801-XXX
(1)
ELECTRONIC COMPONENTS OF ASSESSED IEC 60384-13-1  (4)
QUALITY IN ACCORDANCE WITH: QC 301801

FIXED POLYPROPYLENE  (5)
(3)
FILM DIELECTRIC METAL
FOIL DC CAPACITORS
Outline drawing: (see Table 1)
(.angle projection)
(6)
(7)
Assessment level(s): E  (8)
(Other shapes are permitted within the dimensions given.)
Stability class:
Information on the availability of components qualified to this
detail specification is given in IEC QC 001005

(9)
1 General data
1.1 Recommended method(s) of mounting
See IEC 60384-13, 1.4.2.
1.2 Dimensions
Table 1 – Case size reference and dimensions
Case size Dimensions (in mm)
reference
L H d .
∅
When there is no case size reference, Table 1 may be omitted and the dimensions shall be
given in Table 2, which then becomes Table 1.
The dimensions shall be given as maximum dimensions or as nominal dimensions with a
tolerance.
60384-13-1 © IEC:2006(E) – 7 –
1.3 Ratings and characteristics
Capacitance range   (see Table 2)
Tolerance on rated capacitance
Rated voltage    (see Table 2)
Category voltage (if applicable)  (see Table 2)
Climatic category
Rated temperature
Maximum a.c. voltage (if applicable)
Tangent of loss angle
Insulation resistance
Table 2 – Values of capacitance and of voltage related to case sizes
Rated voltage
a
Category voltage
Case size Case size Case size Case size
Nominal capacitance
(in pF, nF and/or μF)
a
If different from the rated voltage.
...