IEC 62329-3-100:2010

Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 100: Heat-shrinkable moulded shape dimensions

IEC 62329-3-100:2010 gives the dimensional requirements for heat-shrinkable moulded shapes. The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers for options. These moulded shapes are normally supplied in the styles and dimensions given in Tables 1 to 22. The colour is normally black.

Profilés thermorétractables - Partie 3: Exigences relatives aux dimensions des profilés, exigences de matériaux et performances de compatibilité - Feuille 100: Dimensions des profilés thermorétractables

La CEI 62329-2-100:2010 donne les exigences dimensionnelles pour les profilés thermorétractables. Les profilés peuvent être fournis avec un adhésif prérevêtu. Pour les différentes options, consulter les fabricants/fournisseurs. Ces profilés sont généralement fournis dans les modèles et les dimensions indiqués dans les Tableaux 1 à 22. Ils sont généralement de couleur noire.

General Information

• Status: Published
• Publication Date: 15-Jun-2010
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 29.035.01 - Insulating materials in general
• Technical Committee: TC 15 - Solid electrical insulating materials
• Drafting Committee: WG 5 - TC 15/WG 5
• Current Stage: PPUB - Publication issued
• Start Date: 15-Jul-2010
• Completion Date: 16-Jun-2010

Standards Content (Sample)

IEC 62329-3-100
®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Heat-shrinkable moulded shapes –
Part 3: Specification requirements for shape dimensions, material requirements
and compatibility performance – Sheet 100: Heat-shrinkable moulded shape
dimensions

Profilés thermorétractables –
Partie 3: Exigences relatives aux dimensions des profilés, exigences de
matériaux et performances de compatibilité – Feuille 100: Dimensions des
profilés thermorétractables

IEC 62329-3-100:2010

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2010 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC 62329-3-100
®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Heat-shrinkable moulded shapes –
Part 3: Specification requirements for shape dimensions, material requirements
and compatibility performance – Sheet 100: Heat-shrinkable moulded shape
dimensions

Profilés thermorétractables –
Partie 3: Exigences relatives aux dimensions des profilés, exigences de
matériaux et performances de compatibilité – Feuille 100: Dimensions des
profilés thermorétractables

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
V
CODE PRIX
ICS 29.035.01 ISBN 978-2-88912-009-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – 62329-3-100 © IEC:2010
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references .7
3 Designation .7
4 Requirements .8

Figure 1 – Style AA (small lipped bottle) .9
Figure 2 – Style A (lipped short bottle with short body) .10
Figure 3 – Style B (lipped straight bottle with medium body) .11
Figure 4 – Style C (lipped straight bottle with long body).12
Figure 5 – Style D (non-lipped straight bottle) .13
Figure 6 – Style E (lipped straight bottle with long tail).14
Figure 7 – Style F (lipped right-angle boot) .15
Figure 8 – Style G (non-lipped right-angle boot).16
Figure 9 – Style H (lipped right-angle boot with long tail) .17
Figure 10 – Style I (lipped right-angle boot with longer tail).18
Figure 11 – Style J (lipped straight bottle with longer tail) .19
Figure 12 – Style K (non-lipped straight long tail boot) .20
Figure 13 – Style L (transitions ("T" junction)) .21
Figure 14 – Style M (transitions (30°/45° junction)) .22
Figure 15 – Style N (transitions ("Y" junction 45° low profile)) .23
Figure 16 – Style O (straight, high ratio lipped boot) .24
Figure 17 – Style P (transitions ("Y" junction)) .25
Figure 18 – Style R (transitions (three branched outlets)) .26
Figure 19 – Style S (transitions (four branched outlets)) .27
Figure 20 – Style T (D sub-miniature boot straight) .28
Figure 21 – Style U (D sub-miniature boot right angle) (longitudinal).29
Figure 22 – Style V (D sub-miniature boot right angle) (across width)) .30

Table 1 – Dimensions in millimetres of style AA .9
Table 2 – Dimensions in millimetres of style A .10
Table 3 – Dimensions in millimetres of style B .11
Table 4 – Dimensions in millimetres of style C .12
Table 5 – Dimensions in millimetres of style D .13
Table 6 – Dimensions in millimetres of style E .14
Table 7 – Dimensions in millimetres of style F .15
Table 8 – Dimensions in millimetres of style G .16
Table 9 – Dimensions in millimetres of style H .17
Table 10 – Dimensions in millimetres of style I.18
Table 11 – Dimensions in millimetres of style J .19

---------------------- Page: 4 ----------------------
62329-3-100 © IEC:2010 – 3 –
Table 12 – Dimensions in millimetres of style K .20
Table 13 – Dimensions in millimetres of style L.21
Table 14 – Dimensions in millimetres of style M.22
Table 15 – Dimensions in millimetres of style N .23
Table 16 – Dimensions in millimetres of style O .24
Table 17 – Dimensions in millimetres of style P .25
Table 18 – Dimensions in millimetres of style R .26
Table 19 – Dimensions in millimetres of style S .27
Table 20 – Dimensions in millimetres of style T.28
Table 21 – Dimensions in millimetres of style U .29
Table 22 – Dimensions in millimetres of style V .30

---------------------- Page: 5 ----------------------
– 4 – 62329-3-100 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HEAT-SHRINKABLE MOULDED SHAPES –

Part 3: Specification requirements for shape dimensions,
material requirements and compatibility performance –
Sheet 100: Heat-shrinkable moulded shape dimensions


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62329-3-100 has been prepared by IEC technical committee 15:
Solid electrical insulating materials.
The text of this standard is based on the following documents:
FDIS Report on voting
15/568/FDIS 15/588/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 6 ----------------------
62329-3-100 © IEC:2010 – 5 –
A list of all the parts in the IEC 62329 series, under the general title Heat-shrinkable moulded
shapes, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 7 ----------------------
– 6 – 62329-3-100 © IEC:2010
INTRODUCTION
This International Standard is one of a series that deals with heat-shrinkable moulded shapes
for electrical purposes.
The series consists of three parts:
Part 1: Definitions and general requirements (IEC 62329-1)
Part 2: Methods of test (IEC 62329-2)
Part 3: Specification requirements for shape dimensions, material requirements and
compatibility performance
This standard gives one of the sheets comprising part 3 as follows:
Sheet 100: Heat-shrinkable moulded shape dimensions

---------------------- Page: 8 ----------------------
62329-3-100 © IEC:2010 – 7 –
HEAT-SHRINKABLE MOULDED SHAPES –

Part 3: Specification requirements for shape dimensions,
material requirements and compatibility performance –
Sheet 100: Heat-shrinkable moulded shape dimensions



1 Scope
This sheet of IEC 62329-3 gives the dimensional requirements for heat-shrinkable moulded
shapes.
The moulded shapes may be supplied with a pre-coated adhesive. Refer to the
manufacturers/suppliers for options.
These moulded shapes are normally supplied in the styles and dimensions given in Tables 1
to 22. The colour is normally black.
Styles and dimensions other than those specifically listed in Tables 1 to 22 may be available
as custom items. These items shall be considered to comply with this standard if they comply
with the property requirements listed in the sheets for material performance, with the
exception of dimensions.
Materials that conform to this specification meet established levels of performance. However,
the selection of a material by a user for a specific application should be based on the actual
requirements necessary for adequate performance in that application and not based on this
specification alone.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 62329-1, Heat-shrinkable moulded shapes – Part 1: Definitions and general requirements
IEC 60757:1983, Code for designation of colours
3 Designation
The moulded shapes shall be designated as shown by the following example:
Description IEC IEC Part IEC Sheet IEC Colour Adhesive Drain holes
publication number number style/size a b
number code
c
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Moulded IEC 62329 3 101 B/01 BK W1 D
shapes

a
Insert UC if uncoated.
b
Insert N if no drain holes.
c
Sheets for material requirements and compatibility performance.

---------------------- Page: 9 ----------------------
– 8 – 62329-3-100 © IEC:2010
Any abbreviation for colour shall comply with IEC 60757. Where no abbreviation is given, the
colour shall be written in full.
4 Requirements
In addition to the general requirements given in IEC 62329-1, the heat-shrinkable moulded
shapes shall comply with the requirements in Tables and Figures 1 to 22 and the sheets for
material and compatibility performance.

---------------------- Page: 10 ----------------------
62329-3-100 © IEC:2010 – 9 –

Recovered As supplied
X
l l
2 3
l
1
Detail X
l
4
IEC  1395/10

Figure 1 – Style AA (small lipped bottle)
Table 1 – Dimensions in millimetres of style AA
Size d d d l l l l S S S Max.

1 2 3 1 2 3 4 1 2 3
code mass
max. max. min. ref. ref. max. b
±10 % ±20 % ±20 % ±30 %
g
a

01 5,2 1,5 9,0 20,0 4,0 6,6 0,8 0,35 0,8 0,6 1,5
02 5,8 2,2 10,0 19,0 11,0 4,5 1,5 0,5 0,8 0,5 1,5
03 5,5 2,0 9,0 5,0 1,0 1,5
25,0 14,0
04 7,0 3,0 12,0 7,5 1,1 1,5
05 8,0 3,5 30,0 19,0 10,0 2,0 1,0 0,7 1,5
17,0 1,3
06 29,0 14,0 1,5
6,9 3,0 11,0
07 39,0 24,0 1,5
NOTE These parts may be available with eyelets for connector protection caps. Refer to the individual manufacturer.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual
3
manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.

d
1
S
2
S
1
d
2
S
2
d
3

---------------------- Page: 11 ----------------------
– 10 – 62329-3-100 © IEC:2010

Recovered As supplied
X
l
l
2 3
l
1
As supplied
Detail X
(size code 02 only)
l
4
IEC  1396/10

Figure 2 – Style A (lipped short bottle with short body)
Table 2 – Dimensions in millimetres of style A
Size Max.
d d d l l l l s s s

1 2 3 1 2 3 4 1 2 3
code mass
a
max. max. min. ±10 % ref. ref. max. ±20 % ±20 % ±30 % b
g
c

01 10,5 6,0 24,0 26,0 9,0 10,0 1,6 1,6
c
02 14,0 3,5 25,0 40,0 13,0 16,0 3,3
03 14,0 6,0 30,0 43,0 20,0 13,0 1,0 1,8 4,5
04 18,0 7,0 31,0 47,0 15,0 18,0 5,5
1,0
05 22,5 8,5 36,0 22,0 20,0 3,3 2,0 10,0
60,0
06 28,0 10,0 43,0 21,0 20,0 2,2 12,7
1,7
07 35,0 16,0 60,0 90,0 32,0 38,0 3,2 1,5 29,5
08 45,0 17,0 66,0 130,0 50,0 50,0 2,0 71,5
2,0 4,0
09 58,0 27,0 82,0 137,0 37,0 62,0 4,0 100,0
NOTE These parts may be available with eyelets for connector protection caps. Refer to the individual manufacturer.
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual
3
manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
c
For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm.

d
1
S
2
S
1
d
2
S
3
d d
3
3
9,0 mm

---------------------- Page: 12 ----------------------
62329-3-100 © IEC:2010 – 11 –
Recovered As supplied
l
5
X
l l
2 3
l
1
Detail X
As supplied

l l
4 4 (size code 02 only)
IEC  1397/10

Figure 3 – Style B (lipped straight bottle with medium body)
Table 3 – Dimensions in millimetres of style B
Size Max.
d d d l l l l l s s s

1 2 3 1 2 3 4 5 1 2 3
code mass
a d
max. max. min. ±10 % ref. ref. max. ± 10 % ± 20 % ± 20 % ± 30 % b
g
c

01 10,5 6,0 24,0 38,0 21,0 10,0 12,0 1,6 2,8
c

02 14,0 3,5 25,0 55,0 28,0 16,0 14,0 4,4
1,0 1,8
03 14,0 6,0 30,0 55,0 32,0 13,0 12,0 5,5
04 18,0 7,0 31,0 67,0 35,0 18,0 8,3
1,0
05 22,5 8,5 36,0 80,0 42,0 20,0 3,3 2,0 14,5
06 28,0 10,0 43,0 79,0 41,0 20,0 2,2 18,0
20,0 1,7
07 35,0 16,0 60,0 110,0 52,0 38,0 3,2 1,5 41,0
08 45,0 17,0 66,0 150,0 70,0 50,0 2,0 87,0
2,0 4,0
09 58,0 27,0 82,0 158,0 58,0 62,0 4,0 121,0
NOTE These parts may be available with eyelets for connector protection caps. Refer to the individual manufacturer.
a
 Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual manufacturer
3
for exact dimensions.
b
 The values of mass may be higher for some material types. Refer to the individual manufacturer.
c
 For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm.
d

The innermost lips are optional.
d
1
S
2
S
1
d
2
S
3
d d
3 3
9,0 mm

---------------------- Page: 13 ----------------------
– 12 – 62329-3-100 © IEC:2010

Recovered As supplied
l l
5 6
X
l l
2 3
l
1
l l l
4 4 4
Detail X
IEC  1398/10

Figure 4 – Style C (lipped straight bottle with long body)
Table 4 – Dimensions in millimetres of style C
Size d d d l l l l l l s s s Max.

1 2 3 1 2 3 4 5 6 1 2 3
code mass
a
c c
max. max. min. ref. ref. max. b
±10 % ±10 % ±10 % ±20 % ±20 % ±30 %
g
01 28,0 10,0 43,0 99,0 61,0 20,0 2,2 1,0 24,5
1,7
02 35,0 16,0 60,0 130,0 72,0 38,0 20,0 3,2 1,5 50,0
3,3 20,0
03 45,0 17,0 66,0 171,0 90,0 50,0 2,0 103,0
2,0 4,0
04 58,0 27,0 82,0 213,0 113,0 62,0 37,0 4,0 184,0
05 58,0 27,0 82,0 178 100,0 48 20 2,0 4,0 4,0 184,0
NOTE These parts may be available with eyelets for connector protection caps. Refer to the individual manufacturer.
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual manufacturer for
3
exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.

c
The innermost lips are optional.

d
1
S
2
S
1
d
2
S
3
d
3

---------------------- Page: 14 ----------------------
62329-3-100 © IEC:2010 – 13 –

Recovered
As supplied

l
1
l l
2 3
IEC  1399/10

Figure 5 – Style D (non-lipped straight bottle)
Table 5 – Dimensions in millimetres of style D
Size d d d l l l s Max.

1 2 3 1 2 3 1
code mass
a
max. max. min. ref. ref. b
±10 % ±20 %
g
01 8,0 3,8 16,0 25,4 14,2 6,0 1,3 1,2
02 10,5 5,6 23,0 38,1 22,0 9,5 1,5 3,3
03 14,5 6,6 28,0 52,5 27,0 15,0 1,8 4,3
04 18,0 7,5 31,0 66,0 37,0 18,0 1,8 7,7
05 24,5 8,6 36,0 73,7 42,0 17,0 1,8 13,6
06 28,5 9,9 42,0 97,0 58,0 21,0 2,0 21,7
07 35,5 16,0 51,0 127,0 65,0 41,0 3,2 54,5
08 44,5 20,3 66,0 160,5 91,0 48,0 3,8 105,0
09 57,5 27,0 81,0 210,0 115,0 61,5 4,2 199,0
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the
3
individual manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.

d
1
S
1
S
1
d
2
d
3

---------------------- Page: 15 ----------------------
– 14 – 62329-3-100 © IEC:2010

Recovered As supplied
X
l l
2 3
l
1
Detail X l
4
IEC  1400/10

Figure 6 – Style E (lipped straight bottle with long tail)

Table 6 – Dimensions in millimetres of style E
Size d d d d l l l l s s s Max.

1 2 3 4 1 2 3 4 1 2 3
code mass
a
max. max. min. min. ±10 % ref. ref. max. ±20 % ±20 % ±30 % b
g
01 12,0 6,5 22,0 22,0 76,0 57,0 3,3
c
02 13,0 2,0 19,0 6,0 60,0 38,0 1,5 4,1
03 15,0 7,5 25,5 25,5 83,0 60,0 4,4
c
04 19,0 2,5 26,0 7,5 74,0 12,0 45,0 1,0 5,7
05 19,0 8,5 29,0 29,0 89,0 63,0 6,5
1,8 1,1
06 23,0 10,0 34,0 34,0 102,0 73,0 8,0
c
07 26,0 3,0 34,0 9,5 84,0 51,0 10,0
3,3
08 30,0 11,0 37,0 37,0 108,0 14,0 72,0 2,1 12,0
c
09 34,0 3,5 43,5 11,5 100,0 12,0 58,0 1,8 10,0
1,7
10 34,0 12,0 43,5 43,5 114,0 74,0 2,0 14,0
15,0
11 41,0 14,5 50,0 50,0 118,0 73,0 2,3 22,0
12 47,0 18,0 62,5 62,5 121,0 71,0 28,0
1,4
16,0 2 2,5
13 60,0 20,0 69,0 69,0 127,0 67,0 38,0
14 67,0 23,0 81,5 81,5 133,0 69,0 47,0
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual
3
manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
c
These sizes have a stepped “as supplied” profile, i.e. d is larger than d .
3 4
d
1
S
2
S
1
d
2
S
3
d
3
d
4

---------------------- Page: 16 ----------------------
62329-3-100 © IEC:2010 – 15 –
Recovered
As supplied

l
1
X
l
5
Detail X

S
2
S
1
d
1
IEC  1401/10

Figure 7 – Style F (lipped right-angle boot)
Table 7 – Dimensions in millimetres of style F
Size d d d l l l l l s s s Max.

1 2 3 1 2 3 4 5 1 2 3
code mass
max. max. min. ref. ref. max. ref. b
±20 % ±20 % ±20 % ±30 %
g
a

c

01 10,5 6,0 24,0 32,0 25,0 19,0 10,0 1,3 2,2
c
02 14,0 6,0 30,0 41,0 27,0 20,0 12,0 1,5 3,3
1,0
03 18,0 7,0 31,0 51,0 31,0 21,0 6,6
15,0 1,8
1,0
04 22,5 8,5 36,0 59,0 38,0 26,0 10,0
3,3
05 28,5 10,0 43,0 71,0 45,0 30,0 16,0 2,0 14,0
1,7
06 35,0 16,0 60,0 101,0 54,0 35,0 32,0 3,3 1,5 39,0
07 45,0 17,0 66,0 134,0 68,0 42,0 50,0 3,8 2,0 71,0
2,0
08 61,0 25,0 82,0 152,0 84,0 52,0 39,0 4,0 4,0 165,0
09 8,0 3,5 17,0 25,0 20,0 15,0 2,0 7,5 1,0 1,3 0,7 2,0
NOTE These parts may be available with eyelets for connector protection caps. Refer to the individual manufacturer.
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual manufacturer
3
for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.

c
For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm.

l
2
l
3
l
4
S
3
d
2
d
3

---------------------- Page: 17 ----------------------
– 16 – 62329-3-100 © IEC:2010

As supplied
Recovered
l
4
S
1
d
1
l
1
IEC  1402/10

Figure 8 – Style G (non-lipped right-angle boot)
Table 8 – Dimensions in millimetres of style G
Size d d d l l l l s Max.

1 2 3 1 2 3 4 1
code mass
a
max. max. min. ref. ref. ref. b
±10 % ±20 %
g
01 7,9 3,8 16,5 17,3 20,1 15,2 4,3 1,0 1,2
02 10,4 5,6 23,6 21,3 22,9 16,5 5,8 1,3 1,7
03 14,2 6,3 28,4 26,9 26,7 18,5 7,1 1,5 3,4
04 17,8 7,1 31,5 36,6 30,5 20,6 10,2 7,7
1,8
05 22,4 8,4 36,0 43,7 35,1 22,9 12,7 10,4
06 27,9 9,7 43,1 53,6 43,9 29,2 17,3 2,0 15,8
07 35,1 15,7 52,3 75,7 52,9 34,0 32,0 3,3 42,0
08 44,5 20,3 66,0 97,5 66,0 42,2 40,6 3,8 77,9
09 57,2 26,7 81,2 128,0 79,2 49,0 56,4 4,6 168,7
10 44,5 20,3 76,2 97,5 66,0 41,7 40,6 3,8 72,2
a
Shapes made from some material types may be supplied with a d reduced diameter. Refer to the individual
3
manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.

S
1
d
2
l
3
l
2
d
3

---------------------- Page: 18 ----------------------
62329-3-100 © IEC:2010 – 17 –
Recovered As supplied
l
1

X
l
4
Detail X
S
1
S
2
d
1
IEC  1403/10



Figure 9 – Style H (lipped right-angle boot with long tail)
Table 9 – Dimensions in millimetres of style H
Size d d d d l l l L s s s Max.
...