Rubber-covered rollers — Determination of apparent hardness — Part 1: IRHD method

ISO 7267-1:2017 specifies a method for the determination of the apparent hardness, expressed in International Rubber Hardness Degrees (IRHD), of vulcanized- or thermoplastic-rubber roller covers. The method is similar in principle to the methods used for the determination of the hardness of rubber in ISO 48 in that it consists essentially of measuring the depth of penetration of a spherical indentor operating under a specified force. The apparatus used is similar to that described in ISO 48, having a base specifically designed for application to roller covers and similar curved surfaces. NOTE With some rollers, there can be significant variation in the thickness of the rubber over the surface of the roller, which could affect the measured apparent hardness.

Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 1: Méthode DIDC

ISO 7267-1:2017 spécifie une méthode de détermination de la dureté apparente des revêtements de cylindres en caoutchouc vulcanisé ou thermoplastique, exprimée en Degrés Internationaux de Dureté du Caoutchouc (DIDC). Dans son principe, la méthode est semblable aux méthodes utilisées pour déterminer la dureté des caoutchoucs vulcanisés décrites dans l'ISO 48, en ce qu'elle consiste essentiellement à mesurer la profondeur de pénétration d'un pénétrateur sphérique opérant sous une force spécifiée. L'appareillage utilisé est semblable à celui décrit dans l'ISO 48, comportant un socle spécifiquement conçu pour être appliqué sur les revêtements de cylindres et sur les surfaces courbes similaires. NOTE Pour certains cylindres, il peut y avoir une variation significative de l'épaisseur de caoutchouc, selon la zone du cylindre, qui peut affecter la dureté apparente mesurée.

General Information

Status
Withdrawn
Publication Date
17-Aug-2017
Withdrawal Date
17-Aug-2017
Current Stage
9599 - Withdrawal of International Standard
Completion Date
20-Aug-2018
Ref Project

Relations

Buy Standard

Standard
ISO 7267-1:2017 - Rubber-covered rollers -- Determination of apparent hardness
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 7267-1:2017 - Cylindres revetus de caoutchouc -- Détermination de la dureté apparente
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7267-1
Fourth edition
2017-08
Rubber-covered rollers —
Determination of apparent
hardness —
Part 1:
IRHD method
Cylindres revêtus de caoutchouc — Détermination de la dureté
apparente —
Partie 1: Méthode DIDC
Reference number
ISO 7267-1:2017(E)
ISO 2017
---------------------- Page: 1 ----------------------
ISO 7267-1:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7267-1:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Time interval between forming and finished grinding, and testing ...............................................................1

5 Conditioning and temperature of test ............................................................................................................................................ 2

6 Apparatus ..................................................................................................................................................................................................................... 2

6.1 Rollers having a radius greater than 50 mm ................................................................................................................. 2

6.2 Rollers having a radius of 4 mm to 50 mm ..................................................................................................................... 2

6.3 Small rollers having a radius less than 4 mm ............................................................................................................... 3

7 Procedure..................................................................................................................................................................................................................... 3

8 Expression of results ........................................................................................................................................................................................ 4

9 Test report ................................................................................................................................................................................................................... 4

Bibliography ................................................................................................................................................................................................................................ 5

© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 7267-1:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,

Subcommittee SC 2, Testing and analysis.

This fourth edition cancels and replaces the third edition (ISO 7267-1:2008), of which it constitutes a

minor revision to update the normative references in Clause 2.
A list of all parts in the ISO 7267 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 7267-1:2017(E)
Introduction

The hardness of a roller covering has traditionally been determined on the finished roller, since it is this

hardness that is critical to the correct functioning of the roller in its end application. Values of hardness,

determined by whichever method is chosen, are therefore dependent not only on the method employed

and on the rubber, but also on the diameter of the roller, the thickness of the covering and, in the case

of thin coverings, on the nature of the roller core. For this reason, the term “apparent hardness” is used

to distinguish between the values obtained by methods described in the various parts of this document

and those that would be obtained for the rubber if it was possible to use the standard test methods for

standard test pieces forming the subjects of other International Standards.

Since rollers vary considerably in size, construction and end use, and in view of the fact that hardness

determinations are made for such different purposes as specification and factory process control, it has

not been possible to standardize on one test method. Consequently, three methods are described in the

ISO 7267 series, each capable of standing alone.
© ISO 2017 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 7267-1:2017(E)
Rubber-cove
...

NORME ISO
INTERNATIONALE 7267-1
Quatrième édition
2017-08
Cylindres revêtus de caoutchouc —
Détermination de la dureté
apparente —
Partie 1:
Méthode DIDC
Rubber-covered rollers — Determination of apparent hardness —
Part 1: IRHD method
Numéro de référence
ISO 7267-1:2017(F)
ISO 2017
---------------------- Page: 1 ----------------------
ISO 7267-1:2017(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 7267-1:2017(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Domaine d'application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Délai entre mise en forme, rectification et essai ................................................................................................................. 2

5 Conditionnement et température d'essai ................................................................................................................................... 2

6 Appareillage .............................................................................................................................................................................................................. 2

6.1 Cylindres de rayon supérieur à 50 mm .............................................................................................................................. 2

6.2 Cylindres de rayon compris entre 4 mm et 50 mm ................................................................................................. 3

6.3 Petits cylindres de rayon inférieur à 4 mm .................................................................................................................... 4

7 Mode opératoire.................................................................................................................................................................................................... 4

8 Expression des résultats............................................................................................................................................................................... 5

9 Rapport d'essai ...................................................................................................................................................................................................... 5

Bibliographie .............................................................................................................................................................................................................................. 6

© ISO 2017 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 7267-1:2017(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.

iso.org/directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www.iso.org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir le lien suivant: www.iso.org/avant-propos.

Le présent document a été élaboré par le comité technique ISO/TC 45, Élastomères et produits à base

d'élastomères, sous-comité SC 2, Essais et analyses.

Cette quatrième édition annule et remplace la troisième édition (ISO 7267-1:2008), dont elle constitue

une révision mineure afin de mettre à jour les références normatives à l’Article 2.

Une liste de toutes les parties de l’ISO 7267 peut être trouvée sur le site internet de l’ISO.

iv © ISO 2017 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 7267-1:2017(F)
Introduction

Traditionnellement, la dureté d'un revêtement de cylindre est déterminée sur le cylindre fini, étant

donné que cette dureté est essentielle au bon fonctionnement du cylindre en service. Quelle que soit

la méthode choisie, les valeurs de la dureté déterminées dépendent donc non seulement de la méthode

utilisée et du caoutchouc, mais aussi du diamètre du cylindre et de l'épaisseur du revêtement et, dans

le cas de revêtements minces, de la nature du noyau du cylindre. C'est pourquoi le terme «dureté

apparente» est utilisé pour faire la distinction entre les valeurs obtenues par les méthodes décrites

dans les diverses parties du présent document et celles qui seraient obtenues pour le caoutchouc s'il

était possible d'utiliser les méthodes d'essai normalisées pour des éprouvettes normalisées faisant

l'objet d'autres Normes internationales.

Étant donné que les cylindres varient considérablement en taille, construction et utilisation finale et

que les déterminations de dureté sont faites à des fins différentes, par exemple la spécification et le

contrôle de la production en usine (CPU), il n'a pas été possible de normaliser une seule méthode d'essai.

Par conséquent, trois méthodes sont décrites dans la série ISO 7267, chacune étant autoportante.

© ISO 2017 – Tous droits réservés v
---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 7267-1:2017(F)
Cylindres revêtus de caoutchouc — Détermination de la
dureté apparente —
Partie 1:
Méthode DIDC

AVERTISSEMENT 1 — Il convient que l'utilisateur du présent document connaisse bien les

pratiques courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les

problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.