ISO 17717:2024
(Main)Meteorological balloons — Specification
Meteorological balloons — Specification
This document specifies the minimum requirements and the test methods for meteorological balloons made from natural rubber latex or natural rubber latex compounded with synthetic rubber emulsion. This document applies to two types of balloons: — Type 1: meteorological balloon by dipping process; — Type 2: meteorological balloon by moulding process.
Ballons météorologiques — Spécifications
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 17717
Second edition
Meteorological balloons —
2024-04
Specification
Ballons météorologiques — Spécifications
Reference number
ISO 17717:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 17717:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 17717:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Colour .2
4.2 Appearance .2
4.3 Size, mass and dimensions .2
4.4 Tensile Property .4
4.4.1 General .4
4.4.2 Tensile strength and elongation at break before accelerated ageing .4
4.4.3 Tensile strength and elongation at break after accelerated ageing .4
4.5 Bursting diameters .4
4.6 Ozone resistance .5
5 Sampling . 5
6 Packing, marking, transport and storage . . 6
6.1 Packing .6
6.2 Marking .6
6.2.1 Paper box .
...
International
Standard
ISO 17717
Second edition
Meteorological balloons —
Specification
Ballons météorologiques — Spécifications
PROOF/ÉPREUVE
Reference number
ISO 17717:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 17717:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 17717:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Colour .2
4.2 Appearance .2
4.3 Size, mass and dimensions .2
4.4 Tensile Property .4
4.4.1 General .4
4.4.2 Tensile strength and elongation at break before accelerated ageing .4
4.4.3 Tensile strength and elongation at break after accelerated ageing .4
4.5 Bursting diameters .4
4.6 Ozone resistance .5
5 Sampling . 5
6 Packing, marking, transport and storage . . 6
6.1 Packing .6
6.2 Marking .6
6.2.1 Paper box .
...
ISO17717:2024(E)
Style Definition
...
Formatted: Right: 1.5 cm, Bottom: 1 cm, Gutter: 0 cm,
ISO /PRF 17717
Section start: New page, Header distance from edge:
1.27 cm, Footer distance from edge: 1.27 cm
ISO/TC 045 45/SC 4/WG 5
Date: 2023-12-31
Secretariat: DSM
Date: 2024-02-16
Formatted: Cover Title_A1
Meteorological balloons — Specification
Ballons météorologiques — Spécifications
PROOF
---------------------- Page: 1 ----------------------
ISO/PRF 17717:2024(Een)
Formatted: Font: Bold
Formatted: Font: Bold
Formatted: HeaderCentered
© ISO 20232024
Formatted: Font: Bold
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication Formatted: Indent: Left: 0 cm, Right: 0 cm, Space
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
Before: 0 pt, No page break before, Adjust space
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
between Latin and Asian text, Adjust space between
at the address below or ISO’s member body in the country of the requester.
Asian text and numbers
Formatted: Default Paragraph Font, French
ISO copyright office
(Switzerland)
CP 401 • Ch. de Blandonnet 8
Formatted: French (Switzerland)
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Formatted: French (Switzerland)
EmailE-mail: copyright@iso.org
Formatted: French (Switzerland)
Website: www.iso.orgwww.iso.org
Formatted: French (Switzerland)
Published in Switzerland
Formatted: French (Switzerland)
Formatted: FooterPageRomanNumber
ii © ISO 2023 – All rights reserved
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/PRF 17717:2024(Een)
Formatted: Font: Bold
Formatted: Font: Bold
Formatted: HeaderCentered, Left
Contents
Formatted: Font: Bold
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Colour . 2
4.2 Appearance . 2
4.3 Size, mass and dimensions . 2
4.4 Tensile Property . 4
4.4.1 General . 4
4.4.2 Tensile strength and elongation at break before accelerated ageing . 4
4.4.3 Tensile strength and elongation at break after accelerated ageing . 4
4.5 Bursting diameters . 5
4.6 Ozone resistance . 5
5 Sampling . 6
6 Packing, marking, transport and storage . 6
6.1 Packing . 6
6.2 Marking . 7
6.2.1 Paper box .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.