Filler metal for brazing - Designation

This document specifies designations for filler materials for brazing on the basis of their chemical composition. The designation includes their solidus/liquidus temperatures. This document applies to the metallic part of filler materials used in brazing products, for example foils, wires, rods, pastes, flux-coated rods or wires and flux-cored rods or wires.

Métaux d'apport de brasage fort — Désignation

Le présent document spécifie les désignations pour les métaux d'apport de brasage fort d’après leur composition chimique. La désignation inclut leurs températures de solidus/liquidus. Le présent document s'applique à la partie métallique des métaux d'apport utilisés pour les produits de brasage fort, par exemple feuillards, fils, baguettes, pâtes, fils ou baguettes enrobés de flux et fils ou baguettes fourrés de flux.

General Information

Status
Published
Publication Date
26-Apr-2024
Current Stage
6060 - International Standard published
Start Date
27-Apr-2024
Due Date
09-Dec-2024
Completion Date
27-Apr-2024
Ref Project

Relations

Effective Date
24-Dec-2022

Buy Standard

Standard
ISO 3677:2024 - Filler metal for brazing - Designation Released:27. 04. 2024
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3677:2024 - Métaux d'apport de brasage fort — Désignation Released:27. 04. 2024
French language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 3677 - Filler metal for brazing - Designation Released:19. 02. 2024
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
REDLINE ISO/PRF 3677 - Filler metal for brazing - Designation Released:19. 02. 2024
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

International
Standard
ISO 3677
Fourth edition
Filler metal for brazing -
2024-04
Designation
Métaux d'apport de brasage fort — Désignation
Reference number
ISO 3677:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 3677:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 3677:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and requirements . 1
4.1 General .1
4.2 First part .1
4.3 Second part .1
4.4 Third part .2
5 Examples . 2

© ISO 2024 – All rights reserved
iii

---------------------- Page: 3 ----------------------
ISO 3677:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the pat
...

Norme
internationale
ISO 3677
Quatrième édition
Métaux d'apport de brasage fort —
2024-04
Désignation
Filler metal for brazing - Designation
Numéro de référence
ISO 3677:2024(fr) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 3677:2024(fr)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2024
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse

© ISO 2024 – Tous droits réservés
ii

---------------------- Page: 2 ----------------------
ISO 3677:2024(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles et exigences . 1
4.1 Généralités .1
4.2 Première partie .1
4.3 Deuxième partie .1
4.4 Troisième partie .2
5 Exemples . 2

© ISO 2024 – Tous droits réservés
iii

---------------------- Page: 3 ----------------------
ISO 3677:2024(fr)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l’ISO n'avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d
...

International
Standard
ISO 3677
Fourth edition
Filler metal for brazing -
Designation
Métaux d'apport de brasage fort — Désignation
PROOF/ÉPREUVE
Reference number
ISO 3677:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 3677:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 3677:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and requirements . 1
4.1 General .1
4.2 First part .1
4.3 Second part .1
4.4 Third part .2
5 Examples . 2
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
iii

---------------------- Page: 3 ----------------------
ISO 3677:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, whic
...

2023-11-30
ISO/DIS PRF 3677:2023(E)
ISO/TC 44/SC 13
Secretariat:  DIN
Date: 2024-02-19
Filler metal for brazing — - Designation
Métaux d'apport de brasage fort — Désignation
PROOF

---------------------- Page: 1 ----------------------
ISO/DIS PRF 3677:2023(E2024(en)
© ISO 20232024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Fax: +41 22 749 09 47
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
© ISO 2023 – All rights reserved
ii
© ISO 2024 – All rights reserved

ii

---------------------- Page: 2 ----------------------
ISO/DIS PRF 3677:2023(E2024(en)
Contents Page
Foreword . iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Symbols and requirements .1
4.1 General .1
4.2 First part .1
4.3 Second part .1
4.4 Third part .2
5 Examples .2

Foreword iv

© ISO 2023 – All rights reserved
iii
© ISO 2024 – All rights reserved

iii

---------------------- Page: 3 ----------------------
ISO/DIS PRF 3677:2023(E2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents.www.iso.org/patents. ISO shall not be held respon
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.