ISO 13583-1:2015
(Main)Centrifugally cast steel and alloy products — Part 1: General testing and tolerances
Centrifugally cast steel and alloy products — Part 1: General testing and tolerances
ISO 13583-1:2015 specifies the requirements for horizontal and vertical centrifugally cast steel and alloy products to be used in the following applications: a) heat resisting; b) corrosion resisting; c) general engineering.
Produits en acier et alliages moulés par centrifugation — Partie 1: Conditions générales d'essais et tolérances
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13583-1
Second edition
2015-09-15
Centrifugally cast steel and alloy
products —
Part 1:
General testing and tolerances
Produits en acier et alliages moulés par centrifugation —
Partie 1: Conditions générales d’essais et tolérances
Reference number
ISO 13583-1:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 13583-1:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13583-1:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 3
5 Supply. 3
6 Mechanical tests . 3
7 Surface finish requirements . 4
8 Minimum sound wall (MSW) thickness and soundness . 4
9 Dimensional and shape tolerances . 4
9.1 General . 4
9.2 Length . 4
9.3 Straightness . 4
9.4 Outside and inside diameters. 5
10 Inspection procedures and standards of acceptance . 6
11 Production welding . 6
12 Supplementary requirements . 6
12.1 General . 6
12.2 Pressure test . 7
12.3 Elevated temperature test . 7
12.4 Acid etch ring test . 7
12.5 Magnetic particle test . 7
12.6 Ferrite determination . 7
12.7 Corrosion testing . 7
12.8 Eddy current testing . 7
12.9 Radiography . 7
12.10 Ultrasonic testing . 7
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13583-1:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 11, Steel castings.
This second edition cancels and replaces the first edition (ISO 13583-1:2000), which has been
technically revised with the following changes:
— in Clause 2, the normative references were replaced with superseding International Standards;
— the former 8.2 having been deleted, the original subclause 8.3 was renumbered 8.2;
— 10.1.1 was revised;
— 10.1.2 was revised.
ISO 13583 consists of the following parts, under the general title Centrifugally cast steel and alloy products:
— Part 1: General testing and tolerances
— Part 2: Materials
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13583-1:2015(E)
Centrifugally cast steel and alloy products —
Part 1:
General testing and tolerances
1 Scope
This part of ISO 13583 specifies the requirements for horizontal and vertical centrifugally cast steel
and alloy products to be used in the following applications:
a) heat resisting;
b) corrosion resisting;
c) general engineering.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.