Plain bearings — Bearing fatigue — Part 2: Test with a cylindrical specimen of a metallic bearing material

This document specifies а method for the determination of the endurance limit in fatigue of bearing materials alone (not attached to steel backing).

Paliers lisses — Fatigue des paliers — Partie 2: Essai d'éprouvettes cylindriques en matériau antifriction métallique

Drsni ležaji - Utrujanje ležaja - 2. del: Preskušanje kovinskega drsnega materiala z vzorčnim valjem

Ta dokument določa metodo za določanje meje vzdržljivosti pri utrujanju drsnih materialov (nepritrjenih na jekleno podlago).

General Information

Status
Published
Publication Date
16-Dec-2021
Current Stage
6060 - International Standard published
Start Date
17-Dec-2021
Due Date
06-Aug-2022
Completion Date
17-Dec-2021

Relations

Buy Standard

Standard
ISO 7905-2:2022
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 7905-2:2022
01-april-2022
Drsni ležaji - Utrujanje ležaja - 2. del: Preskušanje kovinskega drsnega materiala z
vzorčnim valjem
Plain bearings - Bearing fatigue - Part 2: Test with a cylindrical specimen of a metallic
bearing material
Paliers lisses - Fatigue des paliers - Partie 2: Essai d'éprouvettes cylindriques en
matériau antifriction métallique
Ta slovenski standard je istoveten z: ISO 7905-2:2021
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 7905-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 7905-2:2022

---------------------- Page: 2 ----------------------
SIST ISO 7905-2:2022
INTERNATIONAL ISO
STANDARD 7905-2
Second edition
2021-12
Plain bearings — Bearing fatigue —
Part 2:
Test with a cylindrical specimen of a
metallic bearing material
Paliers lisses — Fatigue des paliers —
Partie 2: Essai d'éprouvettes cylindriques en matériau antifriction
métallique
Reference number
ISO 7905-2:2021(E)
© ISO 2021

---------------------- Page: 3 ----------------------
SIST ISO 7905-2:2022
ISO 7905-2:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 7905-2:2022
ISO 7905-2:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specimens . 1
5 Test method . 2
6 E valuation and presentation of test results . 3
Bibliography . 4
iii
© ISO 2021 – All rights reserved

---------------------- Page: 5 ----------------------
SIST ISO 7905-2:2022
ISO 7905-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.