Rolling bearings — Plummer block housings — Boundary dimensions

ISO 113:2010 specifies boundary dimensions for two-bolt plummer block housings primarily intended for rolling bearings in diameter series 0, 1, 2 and 3, as specified in ISO 15, and for four-bolt plummer block housings primarily intended for rolling bearings in diameter series 0, 1 and 2.

Roulements — Paliers — Dimensions d'encombrement

L'ISO 113:2010 spécifie les dimensions d'encombrement des paliers à deux vis de fixation destinés principalement aux roulements des séries de diamètres 0, 1, 2 et 3, tels que définis dans l'ISO 15, et des paliers à quatre vis de fixation destinés principalement aux roulements des séries de diamètres 0, 1 et 2.

Kotalni ležaji - Okrov stoječega ležajnega sklopa - Glavne mere

Ta mednarodni standard določa glavne mere okrova stoječega ležajnega sklopa z dvema vijakoma, namenjenega predvsem za kotalne ležaje serije s premerom 0, 1, 2 in 3, kot je opredeljeno v ISO 15, in okrova stoječega ležajnega sklopa s štirimi vijaki, namenjenega predvsem za kotalne ležaje serije s premerom 0, 1 in 2.

General Information

Status
Published
Publication Date
28-Jun-2010
Technical Committee
Drafting Committee
Current Stage
9093 - International Standard confirmed
Completion Date
09-Sep-2020

Relations

Buy Standard

Standard
ISO 113:2010 - Rolling bearings -- Plummer block housings -- Boundary dimensions
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 113:2015
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 113:2010 - Roulements -- Paliers -- Dimensions d'encombrement
French language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 113
Third edition
2010-07-01


Rolling bearings — Plummer block
housings — Boundary dimensions
Roulements — Paliers — Dimensions d'encombrement





Reference number
ISO 113:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 113:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 113:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 113 was prepared by Technical Committee ISO/TC 4, Rolling bearings.
This third edition cancels and replaces the second edition (ISO 113:1999), of which it constitutes a minor
revision, incorporating updated references and terminology, as well as the addition of an (informative) annex
giving additional boundary dimensions.

© ISO 2010 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 113:2010(E)

Rolling bearings — Plummer block housings — Boundary
dimensions
1 Scope
This International Standard specifies boundary dimensions for two-bolt plummer block housings primarily
intended for rolling bearings in diameter series 0, 1, 2 and 3, as specified in ISO 15, and for four-bolt plummer
block housings primarily intended for rolling bearings in diameter series 0, 1 and 2.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 15, Rolling bearings — Radial bearings — Boundary dimensions, general plan
ISO 5593, Rolling bearings — Vocabulary
ISO 15241, Rolling bearings — Symbols for quantities
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
3.1
two-bolt plummer block housing
housing with two cap bolts and two bolt holes in the base
See Figure 1.
3.2
four-bolt plummer block housing
housing with four cap bolts and four bolt holes in the base
See Figure 2.
4 Symbols
For the purposes of this document, the symbols given in ISO 15241 and the following apply.
The symbols shown in Figures 1 and 2 and the values given in Tables 1 and 2 denote nominal dimensions
unless specified otherwise.
© ISO 2010 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 113:2010(E)
A overall width
A width of base
1
D seating diameter
a
H distance from mounting face to centreline of seating diameter
H height of feet
1
J centre distance between bolt holes (length)
J centre distance between bolt holes (width)
...

SLOVENSKI STANDARD
SIST ISO 113:2015
01-marec-2015
1DGRPHãþD
SIST ISO 113:2001
.RWDOQLOHåDML2NURYVWRMHþHJDOHåDMQHJDVNORSD*ODYQHPHUH
Rolling bearings - Plummer block housings - Boundary dimensions
Roulements - Paliers - Dimensions d'encombrement
Ta slovenski standard je istoveten z: ISO 113:2010
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 113:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 113:2015

---------------------- Page: 2 ----------------------

SIST ISO 113:2015

INTERNATIONAL ISO
STANDARD 113
Third edition
2010-07-01


Rolling bearings — Plummer block
housings — Boundary dimensions
Roulements — Paliers — Dimensions d'encombrement





Reference number
ISO 113:2010(E)
©
ISO 2010

---------------------- Page: 3 ----------------------

SIST ISO 113:2015
ISO 113:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 113:2015
ISO 113:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 113 was prepared by Technical Committee ISO/TC 4, Rolling bearings.
This third edition cancels and replaces the second edition (ISO 113:1999), of which it constitutes a minor
revision, incorporating updated references and terminology, as well as the addition of an (informative) annex
giving additional boundary dimensions.

© ISO 2010 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 113:2015

---------------------- Page: 6 ----------------------

SIST ISO 113:2015
INTERNATIONAL STANDARD ISO 113:2010(E)

Rolling bearings — Plummer block housings — Boundary
dimensions
1 Scope
This International Standard specifies boundary dimensions for two-bolt plummer block housings primarily
intended for rolling bearings in diameter series 0, 1, 2 and 3, as specified in ISO 15, and for four-bolt plummer
block housings primarily intended for rolling bearings in diameter series 0, 1 and 2.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 15, Rolling bearings — Radial bearings — Boundary dimensions, general plan
ISO 5593, Rolling bearings — Vocabulary
ISO 15241, Rolling bearings — Symbols for quantities
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
3.1
two-bolt plummer block housing
housing with two cap bolts and two bolt holes in the base
See Figure 1.
3.2
four-bolt plummer block housing
housing with four cap bolts and four bolt holes in the base
See Figure 2.
4 Symbols
For the purposes of this document, the symbols given in ISO 15241 and the following apply.
The symbols shown in Figures 1 and 2 and the values given in Tables 1 an
...

NORME ISO
INTERNATIONALE 113
Troisième édition
2010-07-01



Roulements — Paliers — Dimensions
d'encombrement
Rolling bearings — Plummer block housings — Boundary dimensions





Numéro de référence
ISO 113:2010(F)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 113:2010(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2010
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2010 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 113:2010(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 113 a été élaborée par le comité technique ISO/TC 4, Roulements.
Cette troisième édition annule et remplace la deuxième édition (ISO 113:1999), dont elle constitue une
révision mineure incorporant une mise à jour des références et de la terminologie, ainsi que l'ajout d'une
Annexe A (informative) donnant des dimensions d'encombrement supplémentaires.

© ISO 2010 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 113:2010(F)

Roulements — Paliers — Dimensions d'encombrement
1 Domaine d'application
La présente Norme internationale spécifie les dimensions d'encombrement des paliers à deux vis de fixation
destinés principalement aux roulements des séries de diamètres 0, 1, 2 et 3, tels que définis dans l'ISO 15, et
des paliers à quatre vis de fixation destinés principalement aux roulements des séries de diamètres 0, 1 et 2.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 15, Roulements — Roulements radiaux — Dimensions d'encombrement, plan général
ISO 5593, Roulements — Vocabulaire
ISO 15241, Roulements — Symboles relatifs aux grandeurs
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 5593 ainsi que les
suivants s'appliquent.
3.1
palier à deux vis de fixation
palier avec deux vis d'assemblage du chapeau et deux trous de fixation dans la semelle
Voir Figure 1.
3.2
palier à quatre vis de fixation
palier avec quatre vis d'assemblage du chapeau et quatre trous de fixation dans la semelle
Voir Figure 2.
4 Symboles
Pour les besoins du présent document, les symboles donnés dans l'ISO 15241 ainsi que les suivants
s'appliquent.
Sauf indication contraire, les symboles représentés aux Figures 1 et 2 et les valeurs données dans les
Tableaux 1 et 2 indiquent des dimensions nominales.
© ISO 2010 – Tous droits réservés 1

---------------------- Page: 4 ----------------------
ISO 113:2010(F)
A largeur totale
A largeur de la semelle
1
D diamètre de la portée
a
H distance de la fac
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.