ISO 10924-3:2015
(Main)Road vehicles — Circuit breakers — Part 3: Miniature circuit breakers with tabs (Blade type), Form CB11
Road vehicles — Circuit breakers — Part 3: Miniature circuit breakers with tabs (Blade type), Form CB11
ISO 10924-3:2015 specifies miniature circuit breakers with tabs (blade-type), Form CB11 for use in road vehicles. It establishes, for this circuit breaker form, the rated current, test procedures, performance requirements and dimensions. ISO 10924-3:2015 is intended to be used in conjunction with ISO 10924‑1 and with ISO 10924‑2. The numbering of its clauses corresponds to that of ISO 10924‑1 whose requirements are applicable, except where modified by requirements particular to this part of ISO 10924. ISO 10924-3:2015 is applicable to circuit breakers with a rated voltage of 14 V and/or 28 V, a current rating of ≤30 A and a breaking capacity of 2 000 A intended for use in road vehicles with a nominal voltage of 12 V and/or 24 V. The circuit breakers are different in dimensions and functions, such as electrically reset, automatic reset, manual reset, and switchable. NOTE This type of circuit breaker is intended to be used in similar applications as miniature fuse-links according to ISO 8820‑3. While the tab dimensions and current ratings can be the same, there might be differences in performance which the user of these products is advised to consider.
Véhicules routier — Coupe circuites — Partie 3: Coupe circuits miniatures avec languette (type languette), Forme CB11
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 10924-3
First edition
2015-04-01
Road vehicles — Circuit breakers —
Part 3:
Miniature circuit breakers with tabs
(Blade type), Form CB11
Véhicules routier — Coupe circuites —
Partie 3: Coupe circuits miniatures avec languette (type languette),
Forme CB11
Reference number
ISO 10924-3:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 10924-3:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 10924-3:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Marking, labelling, and colour coding . 1
5 Tests and requirements . 2
5.1 General . 2
5.1.1 General test conditions . 2
5.1.2 Test sequence plan . 2
5.1.3 Test cable sizes . 3
5.2 Voltage drop . 4
5.2.1 Purpose . 4
5.2.2 Tests . 4
5.2.3 Requirements . 4
5.3 Maximum housing temperature . 4
5.4 Environmental conditions . 4
5.5 Operating time-rating . 4
5.5.1 Purpose . 4
5.5.2 Tests . 4
5.5.3 Requirements . 4
5.6 Current steps . 5
5.7 No current trip and reset temperature . 5
5.8 Absolute breaking capacity . 5
5.8.1 Tests . 5
5.8.2 Requirements . 5
5.9 Breaking capacity . 5
5.9.1 Tests . 5
5.9.2 Requirements . 6
5.10 Strength of terminals . 6
5.11 Endurance . 6
5.11.1 Tests . 6
5.11.2 Requirements . 6
5.12 Dielectric strength. 7
5.12.1 Tests . 7
5.12.2 Requirement . 7
6 Dimensions and designation examples . 7
6.1 Dimensions . 7
6.2 Designation examples . 7
6.2.1 Category B. 7
6.2.2 Category C . 8
6.2.3 Category D . 8
6.2.4 Category F and G . 9
6.2.5 Category H . 9
Bibliography .11
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 10924-3:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 3, Electric
and electronic equipment.
ISO 10924 consists of the following parts, under the general title Road vehicles — Circuit breakers:
—
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.