Rough-terrain trucks — Non-integrated personnel work platforms — Part 1: Design, safety requirements and verification

ISO 18479-1:2015 defines design criteria and safety requirements for non-integrated personnel work platforms (PWPs) which, if approved for use on the rough-terrain truck, can be fitted and secured to the forks, carriage or attachment bracket of a rough-terrain truck to elevate occupants with or without materials and tools to raised work positions without any controls in the platform to control movement. Design, safety requirements and test methods for variable-reach rough-terrain trucks are covered in ISO 10896‑1. Personnel work platforms equipped with controls which affect movement of the rough-terrain truck are excluded from this part of ISO 18479. The requirements of this part of ISO 18479 shall apply except where national or local regulations are more stringent. ISO 18479-1:2015 is not applicable to non-integrated personnel work platforms manufactured before the date of its publication.

Chariots tout-terrain — Plate-formes de personnel non-integrées — Partie 1: Conception, exigences de sécurité et vérification

General Information

Status
Published
Publication Date
07-Dec-2015
Current Stage
9060 - Close of review
Start Date
05-Mar-2021
Ref Project

RELATIONS

Buy Standard

Standard
ISO 18479-1:2015 - Rough-terrain trucks -- Non-integrated personnel work platforms
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 18479-1
First edition
2015-12-15
Rough-terrain trucks — Non-integrated
personnel work platforms —
Part 1:
Design, safety requirements and
verification
Chariots tout-terrain — Plate-formes de personnel non-integrées —
Partie 1: Conception, exigences de sécurité et vérification
Reference number
ISO 18479-1:2015(E)
ISO 2015
---------------------- Page: 1 ----------------------
ISO 18479-1:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 18479-1:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Safety requirements and/or protective/risk reduction measures .................................................................. 2

4.1 General ........................................................................................................................................................................................................... 2

4.2 Compliance ................................................................................................................................................................................................. 2

4.3 Actual capacity ........................................................................................................................................................................................ 2

4.4 Non-integrated PWP design requirements .................................................................................................................... 3

4.4.1 Non-integrated PWP materials and dimensions .................................................................................. 3

4.4.2 Guardrail systems ........................................................................................................................................................... 3

4.4.3 Load supporting elements ....................................................................................................................................... 4

4.4.4 Floor of the platform .................................................................................................................................................... 4

4.4.5 Non-integrated PWP personnel access ........................................................................................................ 4

4.4.6 Platform connection and position .................................................................................................................... 5

4.4.7 Protection from moving parts .............................................................................................................................. 5

5 Verification of safety requirements and/or protective/risk reduction measures ..........................5

5.1 General ........................................................................................................................................................................................................... 5

6 Information for use ............................................................................................................................................................................................ 5

6.1 Manufacturer’s plate .......................................................................................................................................................................... 5

6.2 Capacity warning .................................................................................................................................................................................. 6

© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 18479-1:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical

Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information

The committee responsible for this document is ISO/TC 110, Industrial trucks, Subcommittee SC 4,

Rough-terrain trucks.

ISO 18479 consists of the following parts, under the general title Rough-terrain trucks — Non-integrated

personnel work platforms:
— Part 1: Design, safety requirements and verification
— Part 2: User requirements
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 18479-1:2015(E)
Introduction

This part of ISO 18479 is one of a set of International Standards produced by ISO/TC 110/SC 4 as part

of its program of work regarding standardization of terminology, general safety, performance and user

requirements for rough-terrain trucks (hereafter also referred to as trucks).

This part of ISO 18479 only addresses the design and safety requirements for non-integrated personnel

work platforms and does not address the rough-terrain truck itself. See ISO 10896-1.

This part of ISO 18479 is a type-C standard as stated in ISO 12100.
© ISO 2015 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 18479-1:2015(E)
Rough-terrain trucks — Non-integrated personnel work
platforms —
Part 1:
Design, safety requirements and verification
1 Scope

This part of ISO 18479 defines design criteria and safety requirements for non-integrated personnel

work platforms (PWPs) which, if approved for use on the rough-terrain truck, can be fitted and secured

to the forks, carriage or attachment bracket of a rough-terrain truck to elevate occupants with or without

materials and tools to raised work positions without any controls in the platform to control movement.

Design, safety requirements and test methods for variable-reach rough-terrain trucks are covered

in ISO 10896-1.

Personnel work platforms equipped with controls which affect movement of the rough-terrain truck

are excluded from this part of ISO 18479.

The requirements of this part of ISO 18479 shall apply except where national or local regulations are

more stringent.

This part of ISO 18479 is not applicable to non-integrated personnel work platforms manufactured

before the date of its publication.
2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

ISO 2867, Earth-moving machinery — Access systems

ISO 10896-1, Rough-terrain trucks — Safety requirements and verification — Part 1: Variable-reach trucks

ISO 12100, Safety of machinery — General principles for design — Risk assessment and risk reduction

ISO 16368, Mobile elevating work platforms — Design, calculations, safety requirements and test methods

ISO 18479-2, Rough-terrain trucks — Non-integrated personnel work platforms — Part 2: User

requirements
3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 10896-1, ISO 12100, ISO 16368,

ISO 18479-2 and the following apply.
1) To be published.
© ISO 2015 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 18479-1:2015(E)
3.1
non-integrated personnel work platform
non-integrated PWP

attachment used to lift occupants, tools and materials to elevated work heights without any controls in

the platform to control movement fitted to a rough-terrain truck
3.2
ductile material

material that has a minimum elongation before failure of 10 % and adequate notch impact strength at

the lowest operating temperature for which the non-integrated PWP is rated
3.3
non-ductile material
brittle material
fibreglass-reinforced plastic m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.