ISO/TS 13399-204:2016
(Main)Cutting tool data representation and exchange — Part 204: Creation and exchange of 3D models — Inserts for reaming
Cutting tool data representation and exchange — Part 204: Creation and exchange of 3D models — Inserts for reaming
ISO/TS 13399-204:2016 specifies a concept for the design of cutting items, limited to any kind of replaceable inserts for reaming, using related properties and domains of values. ISO/TS 13399-204:2016 specifies a common way of designing simplified models that contain the following: - definitions and identification of the design features of replaceable inserts for reaming, with a link to the properties used; - definitions and identification of the internal structure of the 3D model that represents the features and the properties of replaceable inserts for reaming; The following are outside the scope of this part of ISO 13399: - applications where these standard data may be stored or referenced; - creation and exchange of simplified 3D models for cutting tools; - creation and exchange of simplified 3D models for tool items; - creation and exchange of simplified 3D models for other cutting items not described in this part of ISO 13399; - creation and exchange of simplified 3D models for adaptive items; - creation and exchange of simplified 3D models for assembly items and auxiliary items.
Représentation et échange des données relatives aux outils coupants — Partie 204: Création et échange de modèles 3D — Plaquettes d´alésage
L'ISO/TS 13399-204:2016 spécifie un concept pour la conception des éléments coupants, limité à tous les types de plaquettes amovibles d'alésage, utilisant les propriétés et domaines de valeurs associés. L'ISO/TS 13399-204:2016 spécifie une façon commune de concevoir des modèles simplifiés contenant les éléments suivants: - des définitions et identifications des caractéristiques de conception des plaquettes amovibles d'alésage, avec un lien vers les propriétés utilisées; - des définitions et identifications de la structure interne du modèle 3D qui représente les caractéristiques et les propriétés des plaquettes amovibles d'alésage; Les éléments suivants n'entrent pas dans le domaine d'application de la présente partie de l'ISO 13399: - les applications où les données standards peuvent être stockées ou référencées; - la création et l'échange de modèles 3D simplifiés pour outils coupants; - la création et l'échange de modèles 3D simplifiés pour des éléments relatifs aux outils; - la création et l'échange de modèles 3D simplifiés pour d'autres éléments coupants non décrits dans la présente partie de la norme ISO 13399; - la création et l'échange de modèles 3D simplifiés pour les éléments relatifs aux attachements; - la création et l'échange de modèles 3D simplifiés pour les éléments relatifs aux assemblages et éléments auxiliaires.
General Information
Buy Standard
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 13399-204
First edition
Cutting tool data representation and
exchange —
Part 204:
Creation and exchange of 3D models
— Inserts for reaming
Représentation et échange des données relatives aux outils coupants —
Partie 204: Création et échange de modèles 3D — Plaquettes pour
l´alésage
PROOF/ÉPREUVE
Reference number
ISO/TS 13399-204:2015(E)
©
ISO 2015
ISO/TS 13399-204:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO/TS 13399-204:2015(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 1
3.1 General . 1
3.2 Reference system . 2
3.3 Coordinate systems . 2
3.3.1 General. 2
3.3.2 Coordinate system for the location of the insert . 2
3.3.3 Coordinate system for the mounting of the insert . 3
3.4 Planes . 3
4 Design of the model . 4
5 Reaming insert with one cutting edge and double plug chamfer . 4
5.1 General . 4
5.2 Necessary properties . 4
5.3 Basic geometry . 5
5.4 Detailed geometry . 5
6 Reaming insert with two cutting edges and double plug chamfer .6
6.1 General . 6
6.2 Necessary properties . 6
6.3 Basic geometry . 7
6.4 Detailed geometry . 7
7 Reaming insert with one cutting edge and rounded corner . 8
7.1 General . 8
7.2 Necessary properties . 8
7.3 Basic geometry . 9
7.4 Detailed geometry . 9
8 Reaming insert with two cutting edges and rounded corner .10
8.1 General .10
8.2 Necessary properties .10
8.3 Basic geometry .10
8.4 Detailed geometry .10
9 Reaming insert with special cutting profile .11
9.1 General .11
9.2 Necessary properties .11
9.3 Basic geometry .12
9.4 Detailed geometry .12
10 Attributes of surfaces — Visualization of the model features .12
11 Structure of the design elements (tree of model) .12
11.1 General .12
11.2 Example of the structure of the design elements .12
12 Data exchange model .13
Annex A (informative) Information about nominal dimensions .14
Bibliography .15
ISO/TS 13399-204:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 29, Small tools.
ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation
and exchange:
— Part 1: Overview, fundamental principles and general information model
— Part 2: Reference dictionary for the cutting items [Technical Specification]
— Part 3: Reference dictionary for tool items [Technical Specification]
— Part 4: Reference dictionary for adaptive items [Technical Specification]
— Part 5: Reference dictionary for assembly items [Technical Specification]
— Part 50: Reference dictionary for reference systems and common concepts [Technical Specification]
— Part 60: Reference dictionary for connection systems [Technical Specification]
— Part 80: Creation and exchange of 3D models — Overview and principles [Technical Specification]
— Part 100: Definitions, principles and methods for reference dictionaries [Technical Specification]
— Part 150: Usage guidelines [Technical Specification]
— Part 201: Creation and exchange of 3D models — Regular inserts [Technical Specification]
— Part 202: Creation and exchange of 3D models — Irregular inserts [Technical Specification]
— Part 203: Creation and exchange of 3D models — Replaceable inserts for drilling [Technical Specification]
— Part 204: Creation and exchange of 3D models — Inserts for reaming [Technical Specification]
— Part 301: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies [Technical Specification]
iv PROOF/ÉPREUVE © ISO 2015 – All rights reserved
ISO/TS 13399-204:2015(E)
— Part 302: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of solid drills and countersinking tools [Technical Specification]
The following parts are under preparation:
— Part 51: Designation system for customer solution cutting tools [Technical Specification]
— Part 70: Graphical data layout — Layer settings for tool designs [Technical Specification]
— Part 71: Graphical data layout — Creation of documents for the standardized data exchange — Graphical
product information [Technical Specification]
— Part 72: Creation of documents for the standardized data exchange — Definition of properties for
drawing header and their XML-data exchange [Technical Specification]
— Part 303: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of end mills with solid cutting edges [Technical Specification]
— Part 304: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of milling cutters with arbor hole and solid cutting edges [Technical Specification]
— Part 307: Creation and exchange of 3D models — End mills for indexable inserts [Technical Specification]
— Part 308: Creation and exchange of 3D models — Milling cutter with arbor hole for indexable inserts
[Technical Specification]
— Part 309: Creation and exchange of 3D models — Tool ho
...
TECHNICAL ISO/TS
SPECIFICATION 13399-204
First edition
2016-02-01
Cutting tool data representation and
exchange —
Part 204:
Creation and exchange of 3D models
— Inserts for reaming
Représentation et échange des données relatives aux outils coupants —
Partie 204: Création et échange de modèles 3D — Plaquettes pour
l´alésage
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 1
3.1 General . 1
3.2 Reference system . 2
3.3 Coordinate systems . 2
3.3.1 General. 2
3.3.2 Coordinate system for the location of the insert . 2
3.3.3 Coordinate system for the mounting of the insert . 3
3.4 Planes . 3
4 Design of the model . 4
5 Reaming insert with one cutting edge and double plug chamfer . 4
5.1 General . 4
5.2 Necessary properties . 4
5.3 Basic geometry . 5
5.4 Detailed geometry . 5
6 Reaming insert with two cutting edges and double plug chamfer .6
6.1 General . 6
6.2 Necessary properties . 6
6.3 Basic geometry . 7
6.4 Detailed geometry . 7
7 Reaming insert with one cutting edge and rounded corner . 8
7.1 General . 8
7.2 Necessary properties . 8
7.3 Basic geometry . 9
7.4 Detailed geometry . 9
8 Reaming insert with two cutting edges and rounded corner .10
8.1 General .10
8.2 Necessary properties .10
8.3 Basic geometry .10
8.4 Detailed geometry .10
9 Reaming insert with special cutting profile .11
9.1 General .11
9.2 Necessary properties .11
9.3 Basic geometry .12
9.4 Detailed geometry .12
10 Attributes of surfaces — Visualization of the model features .12
11 Structure of the design elements (tree of model) .12
11.1 General .12
11.2 Example of the structure of the design elements .12
12 Data exchange model .13
Annex A (informative) Information about nominal dimensions .14
Bibliography .15
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 29, Small tools.
ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation
and exchange:
— Part 1: Overview, fundamental principles and general information model
— Part 2: Reference dictionary for the cutting items [Technical Specification]
— Part 3: Reference dictionary for tool items [Technical Specification]
— Part 4: Reference dictionary for adaptive items [Technical Specification]
— Part 5: Reference dictionary for assembly items [Technical Specification]
— Part 50: Reference dictionary for reference systems and common concepts [Technical Specification]
— Part 60: Reference dictionary for connection systems [Technical Specification]
— Part 80: Creation and exchange of 3D models — Overview and principles [Technical Specification]
— Part 100: Definitions, principles and methods for reference dictionaries [Technical Specification]
— Part 150: Usage guidelines [Technical Specification]
— Part 201: Creation and exchange of 3D models — Regular inserts [Technical Specification]
— Part 202: Creation and exchange of 3D models — Irregular inserts [Technical Specification]
— Part 203: Creation and exchange of 3D models — Replaceable inserts for drilling [Technical Specification]
— Part 204: Creation and exchange of 3D models — Inserts for reaming [Technical Specification]
— Part 301: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies [Technical Specification]
iv © ISO 2016 – All rights reserved
— Part 302: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of solid drills and countersinking tools [Technical Specification]
— Part 303: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of end mills with solid cutting edges [Technical Specification]
— Part 304: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of milling cutters with arbor hole and solid cutting edges [Technical Specification]
— Part 307: Creation and exchange of 3D models — End mills for indexable inserts [Technical Specification]
— Part 308: Creation and exchange of 3D models — Milling cutter with arbor hole for indexable inserts
[Technical Specification]
— Part 312: Creation and exchange of 3D models — Reamers for indexable inserts [Technical Specification]
— Part 401: Creation and exchange of 3D models — Converting, extending and reducing adaptive items
[Technical Specification]
The following parts are under preparation:
— Part 51: Designation system for customer solution cutting tools [Technical Specification]
— Part 70: Graphical data layout — Layer settings for tool designs [Technical Specification]
— Part 71: Graphical data layout — Creation of documents for the standardized data exchange — Graphical
product information [Technical Specification]
— Part 72: Creation of docume
...
SPÉCIFICATION ISO/TS
TECHNIQUE 13399-204
Première édition
2016-02
Représentation et échange des
données relatives aux outils
coupants —
Partie 204:
Création et échange de modèles 3D —
Plaquettes d´alésage
Cutting tool data representation and exchange —
Part 204: Creation and exchange of 3D models — Inserts for reaming
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2016 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .vi
1 Domaine d'application . 1
2 Références normatives . 1
3 Éléments de départ, systèmes de coordonnées, plans . 2
3.1 Généralités . 2
3.2 Système de référence . 2
3.3 Systèmes de coordonnées . 2
3.3.1 Généralités . 2
3.3.2 Système de coordonnées pour l'emplacement de la plaquette . 2
3.4 Plans . 3
4 Conception du modèle . 4
5 Plaquette d'alésage avec une arête de coupe et un double chanfrein .4
5.1 Généralités . 4
5.2 Propriétés nécessaires . 4
5.3 Géométrie de base . 5
5.4 Géométrie détaillée . 6
6 Plaquette d'alésage avec deux arêtes de coupe et un double chanfrein .6
6.1 Généralités . 6
6.2 Propriétés nécessaires . 7
6.3 Géométrie de base . 7
6.4 Géométrie détaillée . 7
7 Plaquette d'alésage avec une arête de coupe et un arrondi de pointe .8
7.1 Généralités . 8
7.2 Propriétés nécessaires . 8
7.3 Géométrie de base . 9
7.4 Géométrie détaillée . 9
8 Plaquette d'alésage avec deux arêtes de coupe et un arrondi de pointe .10
8.1 Généralités .10
8.2 Propriétés nécessaires .10
8.3 Géométrie de base .10
8.4 Géométrie détaillée .10
9 Plaquette d'alésage avec un profil de coupe spécial .11
9.1 Généralités .11
9.2 Propriétés nécessaires .11
9.3 Géométrie de base .12
9.4 Géométrie détaillée .12
10 Attributs des surfaces – Visualisation des caractéristiques du modèle .12
11 Structure des éléments de conception (arbre du modèle) .12
11.1 Généralités .12
11.2 Exemple de la structure des éléments de conception .12
12 Modèle d'échange de données .13
Annexe A (informative) Informations sur les dimensions nominales .14
Bibliographie .15
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www .iso .org/ avant -propos.
Le comité chargé de l'élaboration du présent document est l'ISO/TC 29 Petit outillage
L’ISO 13399 comprend les parties suivantes, présentées sous le titre général Représentation et échange
des données relatives aux outils coupants:
— Partie 1: Vue d'ensemble, principes fondamentaux et modèle général d'informations
— Partie 2: Dictionnaire de référence pour les éléments coupants [Spécification technique]
— Partie 3: Dictionnaire de référence pour les éléments relatifs aux outils [Spécification technique]
— Partie 4: Dictionnaire de référence pour les éléments relatifs aux attachements [Spécification technique]
— Partie 5: Dictionnaire de référence pour les éléments d'assemblage [Spécification technique]
— Partie 50: Dictionnaire de référence pour les systèmes de référence et les concepts communs [Spécification
technique]
— Partie 60: Dictionnaire de référence pour les systèmes de connexion [Spécification technique]
— Partie 80: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399: Vue d'ensemble et
principes [Spécification technique]
— Partie 100: Définitions, principes et méthodes pour les dictionnaires de référence [Spécification
technique]
— Partie 150: Lignes directrices d'utilisation [Spécification technique]
iv © ISO 2016 – Tous droits réservés
— Partie 201: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-2: Modélisation des
plaquettes régulières [Spécification technique]
— Partie 202: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-2: Modélisation des
plaquettes irrégulières [Spécification technique]
— Partie 203: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-2: Modélisation des
plaquettes de perçage échangeables [Spécification technique]
— Partie 204: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-2: Modélisations des
plaquettes d'alésage [Spécification technique]
— Partie 301: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
tarauds, tarauds à refouler et filières de filetage [Spécification technique]
— Partie 302: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
forets monoblocs et des outils de lamage [Spécification technique]
— Partie 303: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
fraises cylindriques à arêtes de coupe non amovibles [Spécification technique]
— Partie 304: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
fraises à alésage et arêtes de coupe non amovibles [Spécification technique]
— Partie 307: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
fraises cylindriques pour plaquettes amovibles [Spécification technique]
— Partie 308: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
fraises à alésage
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.