ISO/TR 8865:1990
(Main)Mining — Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
Mining — Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
Gives guidance on methods of verifying sprocket dimensions specified in ISO 5613. Specifies those dimensions which should be measured to ensure compatibility between chain and sprocket.
Exploitation minière — Lignes directrices sur les méthodes de contrôle dimensionnel des tourteaux d’entraînement pour convoyeurs à chaînes
Rudarstvo - Navodila za kontroliranje mer ozoblenj pogonskih verižnih koles verižnih transporterjev
General Information
Buy Standard
Standards Content (Sample)
ISO/TR
TECHNICAL
REPORT
First edition
1990-12-01
Mining - Guidance on methods of verifying
dimensions of sprocket assemblies for chain
conveyors
Reference number
IS0 8865 : 1990 (El
---------------------- Page: 1 ----------------------
ISO/TR 8865 : 1990 (E)
Foreword
IS0 (the international Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The main task of IS0 technical committees is to prepare International Standards. In ex-
ceptional circumstances a technical committee may propose the publication of a
Technical Report of one of the following types:
-
type 1, when the required support cannot be obtained for the publication of an
International Standard, despite repeated efforts;
-
type 2, when the subject is still under technical development or where for any
other reason there is the future but not immediate possibility of an agreement on an
International Standard;
-
type 3, when a technical committee has collected data of a different kind from
that which is normally published as an International Standard (“state of the art”, for
example).
Technical Reports of types 1 and 2 are subject to review within three years of publica-
tion, to decide whether they can be transformed into International Standards.
Technical Reports of type 3 do not necessarily have to be reviewed until the data they
provide are considered to be no longer valid or useful.
ISO/TR 8865, which is a Technical Report of type 3, was prepared by Technical Com-
mittee ISO/TC 82, M/‘nlng, Sub-Committee SC 2, Components of coalface machinery
using high-tensile round link chains.
International Standard IS0 5613 : 1984 covering drive sprocket assemblies for mining
chain conveyors specifies requirements for a range of sprocket assemblies for use with
twin outboard assemblies. These assemblies incorporate sprocket rings designed to
accept chains complying with IS0 610, shackle type connectors complying with
IS0 1082 and scraper bars complying with IS0 5612.
The dimensions of the component parts of the sprocket assembly are laid down in
IS0 5613 and these dimensions have to be verified in order to check compliance with
the standard. It is stated that the methods to be used for the verification of the dimen-
sions shall be agreed between the purchaser and the manufacturer (IS0 5613 : 1984,
4.3). A number of the dimensions specified, in particular those relating to the tooth
profile of the sprocket, cannot be measured by the direct application of conventional
measuring instruments and it was decided to give some guidance on the special techni-
ques involved.
The member bodies participating in the work of lSO/TC 82/SC 2 studied the problem
and it was found that a number of varying methods and instruments were used, all
equally satisfactory if the appropriate dimensions were controlled to ensure com-
patibility with the other components of the chain assembly.
The committee therefore came to the conclusion that no one method or instrument
need be adopted as the “standard” method but guidance would be helpful on certain
general principles and essential features of the checking gauges. This document is
therefore published in the form of a Technical Report rather than an International
Standard.
0 IS0 1990
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm,
...
SLOVENSKI STANDARD
SIST ISO/TR 8865:1995
01-november-1995
Rudarstvo - Navodila za kontroliranje mer ozoblenj pogonskih verižnih koles
verižnih transporterjev
Mining -- Guidance on methods of verifying dimensions of sprocket assemblies for chain
conveyors
Titre manque
Ta slovenski standard je istoveten z: ISO/TR 8865:1990
ICS:
53.040.20 Deli za transporterje Components for conveyors
73.100.40 Oprema za vleko in dviganje Haulage and hoisting
equipment
SIST ISO/TR 8865:1995 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO/TR 8865:1995
---------------------- Page: 2 ----------------------
SIST ISO/TR 8865:1995
ISO/TR
TECHNICAL
REPORT
First edition
1990-12-01
Mining - Guidance on methods of verifying
dimensions of sprocket assemblies for chain
conveyors
Reference number
IS0 8865 : 1990 (El
---------------------- Page: 3 ----------------------
SIST ISO/TR 8865:1995
ISO/TR 8865 : 1990 (E)
Foreword
IS0 (the international Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The main task of IS0 technical committees is to prepare International Standards. In ex-
ceptional circumstances a technical committee may propose the publication of a
Technical Report of one of the following types:
-
type 1, when the required support cannot be obtained for the publication of an
International Standard, despite repeated efforts;
-
type 2, when the subject is still under technical development or where for any
other reason there is the future but not immediate possibility of an agreement on an
International Standard;
-
type 3, when a technical committee has collected data of a different kind from
that which is normally published as an International Standard (“state of the art”, for
example).
Technical Reports of types 1 and 2 are subject to review within three years of publica-
tion, to decide whether they can be transformed into International Standards.
Technical Reports of type 3 do not necessarily have to be reviewed until the data they
provide are considered to be no longer valid or useful.
ISO/TR 8865, which is a Technical Report of type 3, was prepared by Technical Com-
mittee ISO/TC 82, M/‘nlng, Sub-Committee SC 2, Components of coalface machinery
using high-tensile round link chains.
International Standard IS0 5613 : 1984 covering drive sprocket assemblies for mining
chain conveyors specifies requirements for a range of sprocket assemblies for use with
twin outboard assemblies. These assemblies incorporate sprocket rings designed to
accept chains complying with IS0 610, shackle type connectors complying with
IS0 1082 and scraper bars complying with IS0 5612.
The dimensions of the component parts of the sprocket assembly are laid down in
IS0 5613 and these dimensions have to be verified in order to check compliance with
the standard. It is stated that the methods to be used for the verification of the dimen-
sions shall be agreed between the purchaser and the manufacturer (IS0 5613 : 1984,
4.3). A number of the dimensions specified, in particular those relating to the tooth
profile of the sprocket, cannot be measured by the direct application of conventional
measuring instruments and it was decided to give some guidance on the special techni-
ques involved.
The member bodies participating in the work of lSO/TC 82/SC 2 studied the problem
and it was found that a number of varying methods and instruments were used, all
equally satisfactory if the appropriate dimensions were controlled to ensure com-
patibili
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.