ISO 11446-1:2012

Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 1: 13-pole connectors for vehicles with 12 V nominal supply voltage not intended to cross water fords

This part of ISO 11446 specifies the dimensional characteristics of, and contact allocation and tests and requirements for, 13-pole connectors for the electrical connection of towing and towed vehicles with 12 V nominal supply voltage not intended to cross water fords. It specifies a park socket for receiving and storing the plug when it is disconnected.

Véhicules routiers — Connecteurs pour liaisons électriques entre véhicules tracteurs et véhicules tractés — Partie 1: Connecteurs à 13 contacts pour véhicules à tension d'alimentation nominale de 12 V non destinés à traverser des gués

General Information

• Status: Published
• Publication Date: 01-Mar-2012
• ICS: 43.040.10 - Electrical and electronic equipment
• Technical Committee: ISO/TC 22/SC 32 - Electrical and electronic components and general system aspects
• Drafting Committee: ISO/TC 22/SC 32/WG 9 - Electrical connections between towing and towed vehicles
• Current Stage: 9020 - International Standard under periodical review
• Start Date: 15-Apr-2024
• Completion Date: 15-Apr-2024

Relations

• Revises: ISO 11446:2004 - Road vehicles — Connectors for the electrical connection of towing and towed vehicles — 13-pole connectors for vehicles with 12 V nominal supply voltage
• Effective Date: 04-Feb-2009

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11446-1
First edition
2012-03-01
Road vehicles — Connectors for the
electrical connection of towing and
towed vehicles —
Part 1:
13-pole connectors for vehicles with 12 V
nominal supply voltage not intended to
cross water fords
Véhicules routiers — Connecteurs pour liaisons électriques entre
véhicules tracteurs et véhicules tractés —
Partie 1: Connecteurs à 13 contacts pour véhicules à tension
d’alimentation nominale de 12 V non destinés à traverser des gués
Reference number
ISO 11446-1:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 11446-1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11446-1:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 General . 1
4.2 Plug . 1
4.3 Socket . 3
4.4 Park socket . 5
5 Application of the connector . 7
5.1 Connector positions and free space . 7
5.2 Contact allocation . 7
5.3 Contact designation . 7
5.4 Terminals . 8
5.5 Connecting cable . 8
6 Tests and requirements . 8
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11446-1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the tech
...