ISO 7718-2:2025

Aircraft — Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle — Part 2: Upper deck doors

This document specifies minimum requirements for dimensions and unobstructed space around upper deck passenger doors on the outer skin of civil transport aircraft, applicable when these doors are designed to accept the connection of existing passenger boarding bridges or transfer vehicles. This document is not applicable to existing models of civil transport aircraft, or derivative models with entry into service up to the year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expected to be compatible with ISO 16004.

Aéronefs — Exigences d'interface des portes passagers pour accouplement d'une passerelle passagers ou de véhicules de transfert de passagers — Partie 2: Portes de pont supérieur

General Information

• Status: Published
• Publication Date: 05-Feb-2025
• ICS: 49.100 - Ground service and maintenance equipment
• Technical Committee: ISO/TC 20/SC 9 - Air cargo and ground equipment
• Drafting Committee: ISO/TC 20/SC 9 - Air cargo and ground equipment
• Current Stage: 6060 - International Standard published
• Start Date: 06-Feb-2025
• Due Date: 06-Feb-2025
• Completion Date: 06-Feb-2025

Relations

• Revises: ISO 7718-2:2016 - Aircraft — Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle — Part 2: Upper deck doors
• Effective Date: 10-Jun-2023

Standards Content (Sample)

International
Standard
ISO 7718-2
Third edition
Aircraft — Passenger doors
2025-02
interface requirements for
connection of passenger boarding
bridge or passenger transfer
vehicle —
Part 2:
Upper deck doors
Aéronefs — Exigences d'interface des portes passagers pour
accouplement d'une passerelle passagers ou de véhicules de
transfert de passagers —
Partie 2: Portes de pont supérieur
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
4.1 Minimum obstructed space .1
4.2 Minimum radius of the fuselage .2
4.3 Door sill height.2
4.4 Main deck bridge compatibility .3
Bibliography . 4

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee
SC 9, Air cargo and ground equipment.
This third edition cancels and replaces the second edition (ISO 7718-2:2016), which has been technically
revised.
The main changes are as follows:
— the requirements have been revised to be more precise.
A list of all parts in the ISO 7718 series can be found on th
...