ISO 702-1:2001
(Main)Machine tools — Connecting dimensions of spindle noses and work holding chucks — Part 1: Conical connection
Machine tools — Connecting dimensions of spindle noses and work holding chucks — Part 1: Conical connection
Machines-outils — Dimensions d'assemblage des nez de broche et mandrins porte-pièces — Partie 1: Assemblage conique
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 702-1
Second edition
2001-04-01
Machine tools — Connecting dimensions of
spindle noses and work holding chucks —
Part 1:
Conical connection
Machines-outils — Dimensions d'assemblage des nez de broche et
mandrins porte-pièces —
Partie 1: Assemblage conique
Reference number
ISO 702-1:2001(E)
©
ISO 2001
---------------------- Page: 1 ----------------------
ISO 702-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 702-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 702 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 702-1 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee
SC 8, Work holding spindles and chucks.
This second edition cancels and replaces the first edition (ISO 702-1:1975), of which it constitutes a technical
revision.
ISO 702 consists of the following parts, under the general title Machine tools — Connecting dimensions of spindle
noses and work holding chucks:
— Part 1: Conical connection
— Part 2: Camlock type
— Part 3: Bayonet type
— Part 4: Cylindrical connection
© ISO 2001 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 702-1:2001(E)
Machine tools — Connecting dimensions of spindle noses and
work holding chucks —
Part 1:
Conical connection
1 Scope
This part of ISO 702 specifies the sizes for interchangeability of tapered (type A) lathe spindle noses and
corresponding connecting faces of face plates or work holding chucks.
NOTE The “Camlock”, “bayonet” and cylindrical types are dealt with in ISO 702-2, ISO 702-3 and ISO 702-4, respectively.
2 Interchangeability
In this part of
...
NORME ISO
INTERNATIONALE 702-1
Deuxième édition
2001-04-01
Machines-outils — Dimensions
d'assemblage des nez de broche et
mandrins porte-pièces —
Partie 1:
Assemblage conique
Machine tools — Connecting dimensions of spindle noses and work
holding chucks —
Part 1: Conical connection
Numéro de référence
ISO 702-1:2001(F)
©
ISO 2001
---------------------- Page: 1 ----------------------
ISO 702-1:2001(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifiéà moins que l'ordinateur employéà cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la créationduprésent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2001
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-aprèsouducomité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse
ii © ISO 2001 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 702-1:2001(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiéeaux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude aledroit de fairepartie ducomité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments delaprésente partie de l’ISO 702 peuvent faire l’objet
de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de ne pas
avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 702-1 a étéélaborée par le comité technique ISO/TC 39, Machines-outils,
sous-comité SC 8, Broches porte-pièce et mandrins.
Cette deuxième édition annule et remplace la première édition (ISO 702-1:1975), dont elle constitue une révision
technique.
L'ISO 702 comprend les parties suivantes, présentées sous le titre général Machines-outils — Dimensions
d'assemblage des nez de broche et mandrins porte-pièces:
— Partie 1: Assemblage conique
— Partie 2: Type Camlock
— Partie 3: Type baïonnette
— Partie 4: Assemblage cylindrique
© ISO 2001 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 702-1:2001(F)
Machines-outils — Dimensions d'assemblage des nez de broche et
mandrins porte-pièces —
Partie 1:
Assemblage conique
1 Domaine d'application
La présente partie de l’ISO 702 spécifie les dimensions d’interchangeabilité des nez de broches coniques de tour
(type A) et des faces de raccordement des faux-plateaux correspondants ou des mandrins de serrage.
NOTE L’ISO 702-2, l’ISO 7
...
INTERNATIONAL ISO
STANDARD 702-1
Second edition
2001-04-01
Machine tools — Connecting dimensions of
spindle noses and work holding chucks —
Part 1:
Conical connection
Machines-outils — Dimensions d'assemblage des nez de broche et
mandrins porte-pièces —
Partie 1: Assemblage conique
Reference number
ISO 702-1:2001(E)
©
ISO 2001
---------------------- Page: 1 ----------------------
ISO 702-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 702-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 702 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 702-1 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee
SC 8, Work holding spindles and chucks.
This second edition cancels and replaces the first edition (ISO 702-1:1975), of which it constitutes a technical
revision.
ISO 702 consists of the following parts, under the general title Machine tools — Connecting dimensions of spindle
noses and work holding chucks:
— Part 1: Conical connection
— Part 2: Camlock type
— Part 3: Bayonet type
— Part 4: Cylindrical connection
© ISO 2001 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 702-1:2001(E)
Machine tools — Connecting dimensions of spindle noses and
work holding chucks —
Part 1:
Conical connection
1 Scope
This part of ISO 702 specifies the sizes for interchangeability of tapered (type A) lathe spindle noses and
corresponding connecting faces of face plates or work holding chucks.
NOTE The “Camlock”, “bayonet” and cylindrical types are dealt with in ISO 702-2, ISO 702-3 and ISO 702-4, respectively.
2 Interchangeability
In this part of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.