ISO 6426-2:2002/Amd 1:2012
(Amendment)Horological vocabulary — Part 2: Technical and commercial definitions — Amendment 1
Horological vocabulary — Part 2: Technical and commercial definitions — Amendment 1
Vocabulaire horloger — Partie 2: Définitions technico-commerciales — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6426-2
NORME
Second edition
Deuxième édition
INTERNATIONALE
2002-09-15
AMENDMENT 1
AMENDEMENT 1
2012-08-15
Horological vocabulary —
Part 2:
Technical and commercial definitions
AMENDMENT 1
Vocabulaire horloger —
Partie 2:
Définitions technico-commerciales
AMENDEMENT 1
Reference number
Numéro de référence
ISO 6426-2:2002/Amd.1:2012(E/F)
©
ISO 2012
---------------------- Page: 1 ----------------------
ISO 6426-2:2002/Amd.1:2012(E/F)
COPYRIGHT PROTECTED DOCUMENT
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester. / Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris
la photocopie et les microfilms, sans l'accord écrit de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du
demandeur.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland/Publié en Suisse
ii © ISO 2012 – All rights reserved/Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 6426-2:2002/Amd.1:2012(E/F)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 6426-2:2002 was prepared by Technical Committee ISO/TC 114, Horology,
Subcommittee SC 9, Technical definitions.
© ISO 2012 – All rights reserved/Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 6426-2:2002/Amd.1:2012(E/F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.