ISO 11798:2026
(Main)Information and documentation — Permanence and durability of writing, printing and copying on paper — Requirements and test methods
- Abstract
This document specifies requirements and test methods for evaluation of the permanence and durability of writing, printing and copying on paper stored in libraries, archives, and other protected environments for long periods of time, in which the information recorded on paper must be retained but not necessarily the full artistic quality. It is applicable to: images on white permanent paper according to ISO 9706 or ISO 11108; recording obtained from pens, stamps, copying machines and printers (that can produce monocoloured and/or multicoloured images). It does not apply to: documents stored under harmful conditions, such as high humidity that promotes microbiological attack, excessive heat, radiation (e.g. light), high levels of pollutants, or the risk of water damage (or water contact). Since documents might be kept in non-protected environments before being transferred to protected environments, resistance to water and light is, however, of importance; legal documents, e.g. banking documents, where the authenticity is of primary interest; documents where the information contents are influenced by small colour shifts; documents within the scope of ISO/TC 42, Photography; permanence and durability of books, but if permanent or archival paper is used in combination with recording that meets the requirements of this document, the book content will most likely become permanent; however, book bindings and covers are not included.
- Status
- Published
- Publication Date
- 15-Nov-2026
- Current Stage
- 6060 - International Standard published
- Start Date
- 16-Nov-2026
- Completion Date
- 16-Nov-2026
ISO 11798:2026 is an International Standard from ISO for evaluating the permanence and durability of writing, printing and copying on paper kept for long periods in libraries, archives and other protected environments. It specifies requirements and test methods for paper records where the information must remain readable and stable, even if full artistic quality is not the main concern. The standard is for paper documents made with pens, stamps, copying machines and printers on white permanent paper or archival paper.
What does ISO 11798:2026 specify?
ISO 11798:2026 specifies how to judge whether recorded information on paper stays legible and stable over time in protected storage conditions. It applies to images on white permanent paper according to ISO 9706 or ISO 11108, and to recording made by pens, stamps, copying machines and printers that can produce mono-coloured and/or multicoloured images.
The document is organized into scope, normative references, terms and definitions, specimen preparation, required characteristics, test methods and procedure, and test report. Its annexes provide the paper requirements, specimen preparation rules, example print templates and reporting forms.
| Annex | What it covers |
|---|---|
| Annex A | Performance testing paper |
| Annex B | Specimen preparation |
| Annex C | Printout templates for sample preparation of printers and copying machines |
| Annex D | Reporting forms |
ISO 11798:2026 does not cover documents stored under harmful conditions such as high humidity, excessive heat, radiation, high pollutant levels or water damage risk. It also excludes legal documents where authenticity is the primary issue, documents where small colour shifts matter to the information content, documents within ISO/TC 42 Photography, and book bindings and covers.
What are the key requirements of ISO 11798:2026?
ISO 11798:2026 sets out a combined program of appearance, colour, resistance and mechanical-strength checks. The main practical point is that a product or recording method has to keep the image readable and stable after light, water, heat, abrasion and transfer tests, while also avoiding harmful effects on the paper itself.
Specimen preparation and conditioning
Clause 4 requires specimens to be prepared from performance testing paper that meets Annex A, with preparation and recording done under controlled conditions. Paper and recording materials should be conditioned before use, and printed specimens must be dried or cured before testing. In practice, this reduces variability so the result reflects the recording process rather than the laboratory climate.
Clause 4 also requires that reference specimens for mechanical tests come from the same batch and the same section of the paper roll as the test specimens. That matters because the comparison with blank paper is part of the mechanical-strength assessment.
Colour, appearance and stability
Clause 5 requires the recorded image to meet colour-fastness limits after light exposure, water exposure and heat exposure. For printers and other machines, the primary colours are tested individually, and spot colours are tested individually as well. For pens and stamps, the standard focuses on lightness shift.
Clause 5 also requires the recorded image to remain clearly defined, legible and visually even, without feathering, strike-through, blocking or blocking-related transfer. If traces appear outside the intended area and interfere with the information content, the specimen fails. This is important for readers because the standard checks both measurement data and the visual usability of the document.
Abrasion resistance and transfer of recording
Clause 5 requires the image to withstand abrasion and to show no unacceptable flaking, deletions or voids. For printers, the degree of abrasion resistance must reach the level stated in the clause, and pens and stamps have a separate level. Clause 5 also requires no evidence of blocking or image transfer after stacked specimens are exposed to heat and humidity under load.
These checks matter for documents that will be handled, stacked or copied in archives and offices. A record that smears, transfers or loses characters may remain on paper but no longer function as a reliable document.
Mechanical strength of the paper
Clause 5 includes tests for tensile energy absorption and folding endurance, where the recording process itself must not weaken the paper beyond the allowed change relative to blank reference paper. These checks are comparative, using recorded and unrecorded specimens from the same paper batch.
This matters because some inks, toners or processing conditions can weaken paper even when the image itself looks acceptable. The standard therefore checks the substrate as well as the record.
Test methods and reporting
Clause 6 gives the detailed test methods for colour fastness, visual inspection, lightfastness, water resistance, transfer of recording, abrasion resistance, resistance to heat, tensile energy absorption and folding endurance. Clause 7 requires the test report to identify the equipment, the performance testing paper, the preparation conditions, the number of test pieces, the results, any deviations and the final pass/fail statement.
What terms does ISO 11798:2026 define?
ISO 11798:2026 defines the terms needed to describe recorded paper and its evaluation.
- Abrasion resistance - the ability of a recorded document to resist loss of image or text through rubbing or wear.
- Archival paper - paper with high permanence and durability in accordance with ISO 11108.
- Degree of abrasion resistance - the measured retention of an image or text after abrasion, expressed from the change in lightness.
- Document - information on paper obtained by a recording process and treated as a unit in documentation.
- Permanence - the ability to remain chemically and physically stable over long periods.
- Permanent image - an image that shows minimal or no change in characteristics affecting usability after long storage.
- Recording - an image created by writing, printing or copying on paper.
Who uses ISO 11798:2026?
ISO 11798:2026 is used by laboratories, paper manufacturers, printer and copier makers, pen and ink manufacturers, and organizations responsible for records kept in libraries and archives. Quality managers and buyers use it when they need to compare recording systems or paper/ink combinations for long-term retention.
It is also relevant to testing personnel who prepare specimens, run the light, water, abrasion, heat and mechanical-strength tests, and report pass/fail results. In practice, it helps users select compatible paper and recording materials for documents that must remain readable in protected storage.
What changed in ISO 11798:2026 from the previous edition?
ISO 11798:2026 cancels and replaces ISO 11798:2023. The foreword states four technical changes: abrasion resistance requirements were developed and improved, Annex C changed from normative to informative, temperature and humidity tolerances for sample preparation and testing were clarified, and the UV-light dose value in 6.4 was corrected.
Which standards are used with ISO 11798:2026?
ISO 11798:2026 relies on several referenced standards for paper properties, colour measurement, ageing and pen performance.
- ISO 536 - grammage of the performance testing paper.
- ISO 1924-2 - tensile properties used in the mechanical-strength test.
- ISO 2470-1 - ISO brightness of the performance testing paper.
- ISO 4892-2 - xenon-arc light exposure for the lightfastness test.
- ISO 5626 - folding endurance test method.
- ISO 9352 - abrasion testing machine and wear conditions.
- ISO 9706 - permanent paper requirements.
- ISO 11108 - archival paper requirements.
- ISO 12757-1, ISO 14145-1, ISO 27668-1 - pen performance conditions for ballpoint, roller ball and gel ink ball pens.
- ISO 13655 - CIELAB colour measurement used throughout the colour-shift calculations.
What does the ISO 11798:2026 document contain?
ISO 11798:2026 contains the test procedures, calculation methods and reporting structure needed to assess recording on paper. It includes formulas for CIELAB lightness and colour shifts, the degree of abrasion resistance, and the mechanical-strength comparisons, plus detailed instructions for sample preparation and environmental conditioning.
The annexes provide the practical materials needed for the tests: paper requirements, specimen-preparation rules, print templates for printers and copying machines, and reporting forms. The tables and figures support laboratory work by showing the required specimen layouts, colour-patch use, and the information that should be recorded in the test report.
Relations
- Effective Date
- 25-Jan-2025
Frequently Asked Questions
ISO 11798:2026 is a standard published by the International Organization for Standardization (ISO). Its full title is "Information and documentation — Permanence and durability of writing, printing and copying on paper — Requirements and test methods". This standard covers: This document specifies requirements and test methods for evaluation of the permanence and durability of writing, printing and copying on paper stored in libraries, archives, and other protected environments for long periods of time, in which the information recorded on paper must be retained but not necessarily the full artistic quality. It is applicable to: images on white permanent paper according to ISO 9706 or ISO 11108; recording obtained from pens, stamps, copying machines and printers (that can produce monocoloured and/or multicoloured images). It does not apply to: documents stored under harmful conditions, such as high humidity that promotes microbiological attack, excessive heat, radiation (e.g. light), high levels of pollutants, or the risk of water damage (or water contact). Since documents might be kept in non-protected environments before being transferred to protected environments, resistance to water and light is, however, of importance; legal documents, e.g. banking documents, where the authenticity is of primary interest; documents where the information contents are influenced by small colour shifts; documents within the scope of ISO/TC 42, Photography; permanence and durability of books, but if permanent or archival paper is used in combination with recording that meets the requirements of this document, the book content will most likely become permanent; however, book bindings and covers are not included.
This document specifies requirements and test methods for evaluation of the permanence and durability of writing, printing and copying on paper stored in libraries, archives, and other protected environments for long periods of time, in which the information recorded on paper must be retained but not necessarily the full artistic quality. It is applicable to: images on white permanent paper according to ISO 9706 or ISO 11108; recording obtained from pens, stamps, copying machines and printers (that can produce monocoloured and/or multicoloured images). It does not apply to: documents stored under harmful conditions, such as high humidity that promotes microbiological attack, excessive heat, radiation (e.g. light), high levels of pollutants, or the risk of water damage (or water contact). Since documents might be kept in non-protected environments before being transferred to protected environments, resistance to water and light is, however, of importance; legal documents, e.g. banking documents, where the authenticity is of primary interest; documents where the information contents are influenced by small colour shifts; documents within the scope of ISO/TC 42, Photography; permanence and durability of books, but if permanent or archival paper is used in combination with recording that meets the requirements of this document, the book content will most likely become permanent; however, book bindings and covers are not included.
ISO 11798:2026 is classified under the following ICS (International Classification for Standards) categories: 01.140.20 - Information sciences. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 11798:2026 has the following relationships with other standards: It is inter standard links to ISO 11798:2023. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 11798:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
International
Standard
ISO 11798
Third edition
Information and documentation —
2026-11
Permanence and durability of
writing, printing and copying on
paper — Requirements and test
methods
Information et documentation — Permanence et durabilité
de l'écriture, de l'impression et de la reprographie sur des
documents papier — Prescriptions et méthodes d'essai
Reference number
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of specimens . 4
4.1 Performance testing paper .4
4.2 Sample conditioning prior to preparation .4
4.3 Guidance for sample preparation .4
4.4 Conditioning of specimens .5
4.5 Reference material used for testing of mechanical properties .5
5 Required characteristics . 5
5.1 General .5
5.2 Colour fastness .6
5.3 Visual appearance .6
5.4 Lightfastness .7
5.5 Water resistance .7
5.6 Transfer of recording .7
5.7 Abrasion resistance . . .7
5.8 Resistance to heat .7
5.9 Effects of recording on the mechanical strength of the paper .7
5.9.1 General .7
5.9.2 Tensile energy absorption.8
5.9.3 Folding endurance . . .8
6 Test method and procedure . 8
6.1 General .8
6.2 Colour fastness .8
6.3 Visual appearance .9
6.4 Lightfastness .9
6.5 Water resistance .10
6.6 Transfer of recording .10
6.7 Abrasion resistance . . .11
6.7.1 General .11
6.7.2 Degree of abrasion resistance .11
6.7.3 Partial deletions, flaking and voids . 12
6.8 Resistance to heat . 12
6.9 Effects of recording on the mechanical strength of the paper . 12
6.9.1 General . 12
6.9.2 Tensile energy absorption. 12
6.9.3 Folding endurance . . . 13
7 Test report . 14
Annex A (normative) Performance testing paper .15
Annex B (normative) Specimen preparation .16
Annex C (informative) Printout templates for sample preparation of printers and copying
machines .18
Annex D (informative) Reporting forms .22
Bibliography .25
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 46, Information and documentation,
Subcommittee SC 10, Requirements for document storage and conditions for preservation.
This third edition cancels and replaces the second edition (ISO 11798:2023), which has been technically
revised.
The main changes are as follows.
— The abrasion resistance requirements have been developed and improved.
— The status of Annex C has been changed from normative to informative.
— The temperature and humidity tolerances for sample preparation and testing have been clarified in
several clauses.
2 2
— The UV-light dose value in 6.4 has been corrected from 0,108 J/m to 10,8 MJ/m .
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
For specific archival documents, it is of great importance that writing, printing and copying (recording) on
paper which, during long-term storage in libraries, archives, and other protected environments, undergo
little or no change in properties that affects their use. The documents must preserve their information
content and, thus, enable information storage and information supply for the future. Accordingly, it is
important to study the permanence and durability of recording on paper.
Writing materials and printing equipment meeting the requirements given in this document can be used
in the preparation of paper documents intended for long-term storage and recurrent use. Such documents
contain permanent and durable images, i.e., images likely to be stable and thus undergo little or no change
in properties that influence legibility and the possibility of copying or converting the paper documents to
other information carriers.
This document specifies requirements and testing methods for evaluation of the permanence and durability
of recording on paper. It is primarily intended for images on writing, printing and photo-copying papers
[1] [2]
according to ISO 9706 (permanent paper) or ISO 11108 (archival paper).
Permanent paper and archival paper, used in the preparation of documents, may differ widely in properties
of importance for the quality and permanence of the image. Some properties of an image, such as abrasion
resistance, depend on the combination of the image and the paper. The testing conditions of this document
are chosen so that results representative of most papers on the market to be used for a particular imaging
process, shall be obtained.
In this document, the requirements are given in the following attributes:
— visual image colour strength and appearance;
— lightfastness;
— water resistance;
— transfer of recording;
— abrasion resistance;
— resistance to heat;
— effect of recording, or the recording process, on the mechanical strength of the paper.
Experience has shown that images written with carbon black ink as well as printed images using commercial
printing inks have proved to be consistently reliable. There are, however, many documents where acidic
inks have affected the paper to such an extent that the paper has degraded. Images produced from dry or
liquid toner are also susceptible to ageing problems.
Images printed with modern material and machinery are often completely different from old images with
respect to composition and properties. The rapid development of new printing techniques makes this testing
very important. One printing technology may be replaced by a newer technology within a few years on the
market. Therefore, conclusions based on studies of old documents in libraries and archives are of limited use
when discussing the permanence of modern documents.
Strictly speaking, the only way to test the permanence and durability of recording on paper is to handle
documents and store them under the relevant conditions for long periods of time. In practice, one can only
rely on the observations made on documents kept for a few decades and evaluate the effect of factors known
to influence the permanence and durability of the image. Therefore, the testing according to this document
does not correlate to lifetime of documents, but rather the documents that satisfy the requirements can be
stored for a long time in the future in archives and protected environments, probably for several hundred
years.
v
International Standard ISO 11798:2026(en)
Information and documentation — Permanence and
durability of writing, printing and copying on paper —
Requirements and test methods
1 Scope
This document specifies requirements and test methods for evaluation of the permanence and durability of
writing, printing and copying on paper stored in libraries, archives, and other protected environments for
long periods of time, in which the information recorded on paper must be retained but not necessarily the
full artistic quality.
It is applicable to:
[1] [2]
— images on white permanent paper according to ISO 9706 or ISO 11108 ;
— recording obtained from pens, stamps, copying machines and printers (that can produce monocoloured
and/or multicoloured images).
It does not apply to:
— documents stored under harmful conditions, such as high humidity that promotes microbiological
attack, excessive heat, radiation (e.g. light), high levels of pollutants, or the risk of water damage (or
water contact). Since documents might be kept in non-protected environments before being transferred
to protected environments, resistance to water and light is, however, of importance;
— legal documents, e.g. banking documents, where the authenticity is of primary interest;
— documents where the information contents are influenced by small colour shifts;
— documents within the scope of ISO/TC 42, Photography;
— permanence and durability of books, but if permanent or archival paper is used in combination with
recording that meets the requirements of this document, the book content will most likely become
permanent; however, book bindings and covers are not included.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 536, Paper and board — Determination of grammage
ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation
method (20 mm/min)
ISO 2470-1, Paper, board and pulps — Measurement of diffuse blue reflectance factor — Part 1: Indoor daylight
conditions (ISO brightness)
ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 5626, Paper — Determination of folding endurance
ISO 9352, Plastics — Determination of resistance to wear by abrasive wheels
ISO 9706, Information and documentation — Paper for documents — Requirements for permanence
ISO 11108, Information and documentation — Archival paper — Requirements for permanence and durability
ISO 12757-1, Ball point pens and refills — Part 1: General use
ISO 13655, Graphic technology — Spectral measurement and colorimetric computation for graphic arts images
ISO 14145-1, Roller ball pens and refills — Part 1: General use
ISO 27668-1, Gel ink ball pens and refills — Part 1: General use
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
abrasion resistance
rub resistance
characteristic of a document with recording (3.14) against losses of image (3.7) or text from the action of
abrasion (i.e., the ability of materials and structures to withstand mechanical wear or rubbing by means of
friction)
Note 1 to entry: Abrasion resistance is measured in this document as the degree of abrasion resistance (3.4).
3.2
archival paper
paper of high permanence (3.11) and high durability (3.6) in accordance with ISO 11108
3.3
CIELAB lightness and colour shift
lightness difference ( ) and colour differences ( and ) measured between two coordinates in the
CIELAB colour space
Note 1 to entry: CIELAB colour space is a three-dimensional, approximately uniform colour space, produced by
plotting, in rectangular coordinates L*, a*, b*. It was defined by the International Commission on Illumination (CIE) in
1976 (Synonymously referred to as CIE 1976 L*a*b*, CIELAB colour space or CIELAB values.).
Note 2 to entry: The quantity L* is a measure of the lightness, where L* = 0 corresponds to black and L* = 100
corresponds to the perfect reflecting diffuser. Visually, the quantities a* and b* represent, respectively, the red-green
and yellow-blue axes in colour space, such that:
— +a* is a measure of the degree of redness;
— −a* is a measure of the degree of greenness;
— +b* is a measure of the degree of yellowness;
— −b* is a measure of the degree of blueness.
If both a* and b* are equal to zero, the test piece is white, grey or black depending on L*.
[3]
Note 3 to entry: Adapted from ISO 5631-2:2022 , 3.6.
3.4
degree of abrasion resistance
R
a
measure of the magnitude of retain of images (3.7), or text, on paper because of abrasion (or wear, or rubbing)
Note 1 to entry: Degree of abrasion resistance is evaluated by measuring the % of changes in L* of a printed image or
[4]
text prior to and after the abrasion test, measured in accordance with ISO 13655 , and is calculated in accordance
with Formula (6) in 6.7.2.
3.5
document
information on paper obtained from a recording (3.14) process which can be treated as a unit in a
documentation process
[5]
[SOURCE: ISO 5127:2017 , 3.1.1.38, modified — "material object" and Notes to entry have been deleted
from the definition.]
3.6
durability
ability to resist the effect of physical stress, such as wear and tear, pressure, or damage during recurrent use
3.7
image
visual representation with colourants (such as dyes or pigments) distributed on paper as text characters,
lines, colour patches or other visually identifiable patterns
3.8
monochromatic image
image (3.7) created with a recording (3.14) process uniformly in one colour
Note 1 to entry: Images produced in one colour from a black and white printer, or any colour from a printer that can
produce other colours, such as black, cyan, magenta and yellow.
3.9
multicoloured image
image (3.7) created with a recording (3.14) process in more than one colour, where the colours constitute
part of the information contents
Note 1 to entry: It can be separated into different primary colours (e.g., black, cyan, magenta and yellow).
Note 2 to entry: Not to be confused with a coloured image. In this document, a coloured image is referred to as an
image in any colour as a monochromatic image (3.8).
3.10
performance testing paper
permanent paper (3.13) or archival paper (3.2) used for sample preparation
Note 1 to entry: The performance testing paper shall be handled in accordance with 4.1 and meet the requirements of
Annex A.
3.11
permanence
ability to remain chemically and physically stable over long periods of time
3.12
permanent image
image (3.7) that, when stored over long periods in libraries, archives, or other controlled environments,
exhibits minimal or no alteration in characteristics that influence its usability
3.13
permanent paper
[1]
paper of high permanence (3.11) in accordance with ISO 9706
3.14
recording
image (3.7) created by the process of writing, printing and copying on paper
Note 1 to entry: Recording can be obtained from pens, stamps, copying machines and printers.
3.15
spot colour image
image (3.7) created with a recording (3.14) process using specialized ink mixes to create a specific
predetermined uniform colour in commercial printing
3.16
sample
aggregate of all the specimen (3.17) taken to be representative of a lot
[6]
[SOURCE: ISO 4046-5:2016 , 5.100]
3.17
specimen
portion of a paper or board sample (in this context performance testing paper with recording from the
tested writing, printing, or copying equipment) sufficient in size so that test pieces (3.18) can be obtained
from it
[6]
[SOURCE: ISO 4046-5:2016 , 5.106, modified — text in brackets has been added.]
3.18
test piece
piece or pieces of paper specimen (3.17) on which the measurement is carried out in accordance with the
stipulations of the method of test
[6]
[SOURCE: ISO 4046-5:2016 , 5.118, modified — Note to entry has been omitted.]
4 Preparation of specimens
4.1 Performance testing paper
The paper used for production of specimens shall meet the requirements of Annex A.
When using archival paper (in accordance with ISO 11108) as performance testing paper, watermarks can
be present on various spots throughout the specimens. Such imprints are basically attenuations of the paper
and indicate authenticity. To avoid misleading test results, test pieces shall be prepared from areas of the
paper specimens that are free of watermarks when testing is performed in accordance with 6.2, 6.4, 6.5, 6.7,
6.8 and 6.9.
4.2 Sample conditioning prior to preparation
Material (including paper) should be conditioned for at least 15 h at (23 ± 2) °C and (50 ± 5) % RH before
the recording process. The recording process should be performed in the same atmosphere. If this is not
possible, instructions from the manufacturer of the recording equipment to be tested shall be followed.
4.3 Guidance for sample preparation
Specimens for testing purposes shall be prepared in accordance with the instructions of the manufacturer
of the recording equipment.
The test patterns shall conform to Clause 6 using the same writing, printing, and copying methods, using
identical combinations of ink, toner, and paper as those intended for the final application or use case.
Characters, spacing, etc. shall represent normal use of the recording equipment intended for testing.
Specimen preparation shall also meet the requirements of Annex B.
Three example printout templates and the number of specimens that can be used for sample preparation of
printers are given in Table C.1 of Annex C.
Print adjustments and settings are very important parameters to acknowledge, since different settings
on a printer can have significant impact on the quality of printed images. Thus, adjusting the settings can
drastically change the the printing and impact its permanence. Accordingly, for printers and other recording
equipment, in addition to their manufacturer/brand, model number and serial number, note and report the
print adjustment and settings (such as paper setting, driver setting, colour mode and printing speed used), if
specific print adjustments are to be made.
4.4 Conditioning of specimens
Printed specimens shall be dried or cured and conditioned to the level of the intended use prior to testing.
The specimens shall be kept at (23 ± 2) °C and (50 ± 5) % RH for at least 24 h (depending on the type of
printing method) prior to further test piece preparation and testing. Inks that must evaporate or cure, such
as water-based inkjet-printed specimens, shall be conditioned at least 7 days prior to the testing.
An environment of (23 ± 2) °C and (50 ± 5) % RH is also valid for all testing except when testing the
mechanical properties. When testing the mechanical strength of the paper in accordance with ISO 1924-2
and ISO 5626 (see 6.9), the testing atmosphere shall be (23 ± 1) °C and (50 ± 3) % RH (i.e., not in accordance
[7]
with ISO 187 as described in those International Standards).
The specimens shall not be touched with bare hands.
NOTE Testing of mechanical properties in accordance with this document is comparative in nature, involving
papers with recording evaluated against papers without recording, all handled in the same manner in accordance
with this document. As all samples and reference materials are conditioned and tested within the same environment,
they are exposed to identical climate conditions and share the same conditioning history.
Consequently, requirements for mechanical properties are not expressed as absolute values; instead, the mechanical
assessment is based on the difference in strength between the samples and the reference papers. Under these
[7]
conditions, less stringent climate tolerances than those specified in ISO 187 can be applied without adversely
affecting the quality of the results.
4.5 Reference material used for testing of mechanical properties
Tensile energy absorption (see 6.9.2) and folding endurance (see 6.9.3) are both comparative tests between
test specimens (performance testing paper with recording) and reference specimens (performance testing
paper without recording). Accordingly, to ensure reliable comparison, all performance testing paper (used
for both test and reference specimens) shall originate from the same batch and also from the same section
of the paper roll (i.e., sorted paper). In addition, paper is a sensitive material and is strongly affected by the
surrounding environment, so the reference specimens shall be handled and stored in a similar manner as
the test specimens prior to testing. Due to such unique handling, the reference specimens are restricted to
the corresponding test specimens and cannot be used for other comparative tests.
If test specimens are prepared using recording equipment located outside the laboratory, such as a printer,
the reference specimens shall be brought to all environments where the test specimens are produced. Prior
to the preparation of test pieces in the laboratory, both test and reference specimens should be stored
together, preferably in the same box.
5 Required characteristics
5.1 General
Paper documents conforming to this document shall meet the following requirements. Specimens for testing
shall be prepared as described in Clause 4 and tested in accordance with Clause 6.
5.2 Colour fastness
The colour fastness is evaluated as CIELAB colour shift measured before and after each test when tested in
accordance with 6.4, 6.5 and 6.8, and measured in accordance with 6.2.
Monochromatic images obtained from printing devices shall not exceed the maximum CIELAB lightness
and colour shifts specified in Table 1. For printing devices that can produce multicoloured images (from
e.g. toners or inks), all the primary colours such as cyan, magenta, yellow and black (CMYK), shall be tested
individually to cover all sets of chemical compositions of the multicolour. For spot colour images, each spot
colour shall individually be tested.
The colour tone of the image may change visually but it shall still be recognizable as being of the same colour
as before the treatment.
Table 1 — Maximum CIELAB lightness and colour shifts for printers and other machines
Test property
a b c
5.4 , 5.5 and 5.8 ±8 ±8 ±8 ≤10
All colours except yellow
a b c
5.4 , 5.5 and 5.8 ±8 ±8 ±15 ≤15
Yellow
a
Lightfastness.
b
Water resistance.
c
Resistance to heat.
NOTE 1 is lightness shift and and are colour shifts. is calculated based on both lightness shift and colour
shifts.
NOTE 2 The presented maximum changes are valid for uniform colours, such as cyan, magenta, yellow and black (CMYK).
Images obtained from pens and stamps shall not exceed the maximum CIELAB lightness shifts specified in
Table 2.
For pen writing with blue ink, the colour may shift from blue to green when testing lightfastness and
resistance to heat. This is acceptable if the requirement in Table 2 is met.
Table 2 — Maximum CIELAB lightness shifts for pens and stamps
Test property
a
5.4 ±15
b c
5.5 and 5.8 ±10
a
Lightfastness.
b
Water resistance.
c
Resistance to heat.
Multicoloured images (where colours constitute parts of the information content)
are not possible to produce from pens and stamps, and thus, only lightness shift
is required to measure.
5.3 Visual appearance
5.3.1 Each element of the specimen images shall be clearly defined and easily legible when inspected as
described in 6.3. The colour strength shall be visually even, i.e. no mottling shall be visible. The print density
and colour intensity shall be satisfactory by eye for each colour that is tested. Text characters shall be easily
legible. Feathering or strike-through shall not be visible without magnification.
5.3.2 For printing or copying on paper, if traces of characters are detected outside the intended area on the
paper specimens, anywhere on the white sections of the paper, and the assessment is that this appearance
can interfere with the information content of the document, those specimens shall be regarded as failed.
Such an incident is referred to as ghosting.
5.3.3 For printing devices that can produce multicolours, this visual appearance requirement shall be met
for each primary colour (and spot colour if any).
5.4 Lightfastness
After illumination in accordance with 6.4, images shall meet the requirements of colour fastness in 5.2.
5.5 Water resistance
After treatment with water in accordance with 6.5, images shall meet the requirements of colour fastness in
5.2.
NOTE Resistance to forgery by chemicals can be important for some types of documents, such as banking
[8] [9]
documents. ISO 12757-2 and ISO 14145-2 contain requirements for resistance to chemicals other than water.
The image shall also meet the requirements of 5.3.1 when inspected visually as described in 6.3. However,
noticeable traces of characters can occur on the white adjacent paper loaded against the test piece. This
is acceptable if the image on the test piece meets the requirements stated in the first sentence of this
paragraph.
Only a slight discolouration of the paper is accepted, < 5, when determined in accordance with
6.5.
5.6 Transfer of recording
Test pieces kept in a stack under pressure as described in 6.6 shall show no evidence of blocking (sticking) or
damage to the images after separation. No characters, or parts of characters, shall be visible on the adjacent
paper, but traces of transfer in the form of small dots are acceptable if the image on the test piece meets the
requirements stated in the first sentence of this paragraph.
For printing devices that can produce multicolours, this requirement shall be met for each primary colour
(and spot colour if any).
5.7 Abrasion resistance
When testing abrasion resistance of the image as specified in 6.7, the degree of abrasion resistance, as
specified in 6.7.2, shall be ≥ 60 % for all colours in images produced by printers, and ≥ 50 % for images
produced by pens and stamps.
The abraded surface will be affected by the abrasion procedure, and when inspected visually, smaller fibres
of uniform size can be found, but larger fibres shall not be found.
Flaking of part of the image, causing partial deletions or voids, shall not occur on the test pieces containing
alphabetical characters when abraded as specified in 6.7.3, steps a and b.
5.8 Resistance to heat
Images that have been exposed to heat in accordance with 6.8 shall meet the requirements of colour fastness
in 5.2. The image shall also meet the requirements of 5.3.1 when inspected visually as described in 6.3.
5.9 Effects of recording on the mechanical strength of the paper
5.9.1 General
The mechanical strength of the paper may be negatively affected by the recording process, including heat,
radiation and chemical agents, which can cause its degradation.
For paper documents prepared by recording equipment that involves processes which can cause degradation
of the paper, the requirements of 5.9.2 and 5.9.3 shall be met in both machine- and cross-directions of the
paper. For paper documents prepared by recording equipment where no such processing occurs, only the
requirements of 5.9.2 shall be met in both machine- and cross-direction of the paper. Where specimens
are normally obtainable only in one direction, for example by pens, testing in one direction of the paper is
accepted.
5.9.2 Tensile energy absorption
The tensile energy absorption of the test pieces with recording shall not be lowered by more than 10 % as
compared to the reference pieces (blank paper), when tested as described in 6.9.2. This requirement applies
to both the unaged test pieces as well as to the aged test pieces in accordance with the accelerated ageing
conditions described in 6.8.
5.9.3 Folding endurance
The folding endurance of the test pieces with recording shall not be lowered by more than 0,1 as compared
to the reference pieces (blank paper), when tested as described in 6.9.3. This requirement applies to both
the unaged test pieces as well as to the aged test pieces in accordance with the accelerated ageing conditions
described in 6.8.
6 Test method and procedure
6.1 General
To conform with this document, nine test methods are required. These test methods evaluate how well
recordings on paper withstand various types of stress, including environmental conditions during storage
or display, as well as everyday wear and tear from regular use.
For the testing, prepare specimens as described in each test method and in accordance with Clause 4 and
Annex B.
6.2 Colour fastness
This test examines the colour fastness of recording and is a measure which is used to evaluate the tests of
lightfastness (see 6.4), water resistance (see 6.5) and resistance to heat (see 6.8).
To produce specimens for colour fastness from printing devices, use the printout template with colour
patches attached in Clause C.3 and use the printout template 2, Figure C.4 and Figure C.5. Specimens from
pens and stamps shall be prepared in accordance with Clause B.4 and Clause B.5.
From the specimens, prepare test pieces with colour patches of uniform colour that are appropriate in size
for the intended spectrophotometer. Perform measurements on the colour patches and determine the
CIELAB lightness and colour coordinates L*, a*, b* in accordance with ISO 13655prior to exposure (coordinate
) and after exposure (coordinate ) of each test as described in 6.4, 6.5 and 6.8. Measurement
condition M1 (D50/2°) shall be used with the same paper (without recording) used as background. For
reliable measurement results, multiple test pieces shall be measured in accordance with 6.4, 6.5 and 6.8.
Measurement instruments shall be calibrated in accordance with the manufacturer’s instructions.
For printing devices that can produce multicoloured images, identify each primary colour and perform
measurements on each colour individually, such as cyan, magenta, yellow and black (CMYK). If spot colours
are used, measurements shall be performed on each spot colour with the same procedure. Process colours
shall not be used for the measurements. However, if there are difficulties in producing specimens with
completely pure colours for each primary colour, exceptions can be made.
For pens and stamps, only the lightness shift shall be calculated using Formula (1). For printing devices
and other machines, make calculations of CIELAB lightness and colour shifts , , and as
follows:
— Calculate the lightness shift as shown in Formula (1);
(1)
where
is the lightness coordinate after exposure;
is the lightness coordinate prior to exposure.
— Calculate the colour shifts and as shown in Formula (2) and Formula (3):
(2)
(3)
where
, are the coordinates after exposure;
, are the coordinates prior to exposure.
— Calculate (Euclidean distance between two points) as shown in Formula (4):
(4)
NOTE There are 4 conditions relating illumination spectra specifications in ISO 13655. M0 corresponds to the CIE
[10]
illuminant A, as specified in ISO 5-3 for density measurements, in which UV spectra are not specified. M1 matches
the CIE Illuminant D50, which includes UV spectra equivalent to D50. M2 matches the CIE D50 spectra in the visual
range but excludes UV spectra to remove the effect of fluorescence caused by UV illumination. M3 is the illumination
condition through a polarizer to suppress the influence of surface reflection on the colour coordinates. M1 is used in
this document to measure colour coordinates and their changes which correlate well with colour appearance under
the D50 illuminant determined by colourants and paper properties, and their changes, i.e. degradation of optical
brightener in papers in addition to colourant caused by light exposure.
6.3 Visual appearance
This test examines the appearance of recording, i.e. the readability of images and information on a document
obtained by a recording process.
Prepare at least 5 specimens with lines, alphabetical characters and patches of uniform colour included (for
printing devices, use the printout templates in Clause C.3 and Clause C.4, and for pens and stamps, prepare
specimens in accordance with Clause B.4 and Clause B.5).
Inspect each specimen visually for defects, such as voids or broken characters, bad edge definition,
uneven colour, and others like traces of image characters outside the intended area. In addition, inspect
the specimens with a magnifying glass or an equivalent device at 8X magnification. Evaluate the density,
legibility and colour intensity of the recording. Inspect for feathering or strike-through. Specimens from
each colour shall be inspected individually.
6.4 Lightfastness
This test examines if daylight through a window or strong indoor light has negative impact on a recording.
Lightfastness is a measure of the ability of images to withstand strong light exposure with minimal change
in colour tone. The colour shift is calculated based on CIELAB measurements performed before and after
exposure to light.
For each colour to be tested, prepare test pieces as strips, so that measurements can be made on three colour
patches, in accordance with 6.2.
Illuminate the test pieces with a xenon arc lamp through window glass filters in accordance with method B
of ISO 4892-2. Expose the test pieces for 60 h to achieve the UV-light dose of 10,8 MJ/m using an irradiance
50 W/m at broadband 300 nm to 400 nm. The black panel temperature shall be controlled within (60 ± 3) °C
and the humidity shall be controlled
...



